Installation and Operation Instructions ELECTRIC FIREPLACE XFINS2518-1C REV19-01
Important Safety Instructions Listing Approvals 2-3 4 Operating Instructions 5 Control Buttons/FunctionS 6 Remote Control 7 Troubleshooting 8 Installation 9 Inserting firebox 10 1
CONSUMER SAFETY INFORMATION Read this manual before installing and operating this appliance. Failure to follow these instructions may result in electric shock, fire property damage, personal injury and will void the warranty. Requires the use of Fireplace Mantel. Do not store or use gasoline or other flammable liquids or vapors in the vicinity of this appliance.
12. All electrical heaters have hot and arcing or sparking parts inside. Do not use in areas where gasoline, paint, or flammable liquids are used or stored or where the appliance will be exposed to flammable vapors. 13. Avoid using the appliance with an extension cord. Extension cords may overheat and cause a risk of fire. If an extension cord MUST be used, the cord must be No.16 AWG minimum size and rated not less than 1875 Watts.
LISTING APPROVALS This heater has been tested in accordance with the CSA Standards. Model Number: XFINS2518-1C Description: Electric Fireplace Voltage: 120V AC, 60Hz Watts: MAX 1400W Length: Height: 26.8 18.5 Depth: 10.
OPERATING INSTRUCTIONS Read all instructions and warnings prior to operating the appliance. Ensure that all control are in the "OFF" position before plugging the appliance into a properly grounded electrical outlet.
CONTROL BUTTONS/FUNCTIONS 1 Power ON\OFF:(The master power switch must be "on")Power to the unit. flame brightness and to decrease flame brghtness.You must press the button several times to see the full flame effect 3 Low heat 750 watts 4 High heat 1400 watts 5 Heater Timer: Allows you to leave your heater on with an automatic timer for shut off. You can set your heater to be on for 1/2 hour increments starting at a 1/2 hour up to a maximum of 7-1/2 hours - press once for each 1/2 hour increment.
REPLACING THE LIGHTBULBS The electric fireplace insert uses two (2) clear 120-volt, 40-watt, E-12 socket base lightbulbs (small base, chandelier candle-type bulbs). The lightbulbs are located at the bottom of the unit. You can change the lightbulbs from the back of the electric fireplace. For your convenience, if one of the lightbulbs burns out, it may be easier to replace all of the lightbulbs at the same time. 1. Turn the electric fireplace master power to the “off” position. 2.
Care and maintenance: Turn heater OFF and unplug from electrical outlet before any cleaning or maintenance is performed. Keep combustible materials such as furniture, pillows, bedding, papers, clothing, and curtains at least 3feet (0.9meter) away from fireplace. Use a vacuum or duster to keep heat and vent area clean from dust and dirt. The exterior of the fireplace should be cleaned with a damp cloth or duster. Do not use abrasive cleaners or liquid sprays.
INSTALLATION PLANNING INSTALLATION To avoid scratching the finish, assemble the product on a soft,non-abrasive surface,such as carpet or cardboard. Assembly of this product may require more than one person. TOOLS REQUIRED Safety GogglesPhillips screwdriver HARWARE INCLUDED Note: Hardware not shown to actual size.
Assembly (continued) I Attach the metal brackets(S) to all three sides of the firebox and two sides of the mantel to ensure that your firebox does not move around as you use it. Insert and tighten the 2 (PP) screws. Attach the left and right side trim by inserting and tightening 2 (PP) screws. 1 spare (PP) screw included. x3 PP S Insert the firebox insert(P) into the mantel from the rear. Be careful not to scratch the base(B). Viewing from the front check that the insert is centered.