GigaSpire BLAST Installation Guide
Contents About this Guide....................................................................... 5 Chapter 1: GigaSpire BLAST u4 Overview ............................ 7 GigaSpire Mesh BLAST® u4m Overview ............................................................... 12 Agency Listing ......................................................................................................... 16 Site Preparation ....................................................................................................
Chapter 3: Final Set-up and Testing .................................... 31 BLAST u4/u4m Reset Behavior .............................................................................. 31 Powering the BLAST u4/u4m .................................................................................. 33 Connecting to the Internet ...................................................................................... 34 LED States - Power Off & Boot-up .............................................................
About this Guide This document provides general installation practices for the Calix GigaSpire BLAST U4 and the GigaSpire Mesh BLAST u4m. This document also provides a general description of the products, and guidance for planning, site preparation, power installation, splicing to the outside plant, and basic troubleshooting.
DANGER! CLASS 1 LASER PRODUCT. INVISIBLE LASER RADIATION MAY BE PRESENT. Fiber optic radiation can cause severe eye damage or blindness. Do not look into the open end of an optical fiber. IMPORTANT SAFETY INSTRUCTIONS When using your equipment, basic safety precautions must always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: Do not use this product near water.
Chapter 1 GigaSpire BLAST u4 Overview The Calix GigaSpire BLAST u4 is a new generation smart home system that extends the access network into the home and acts as a strategic location for control of the ultimate WiFi experience. In addition to supporting broadband connectivity of data and video services, this intelligent, high-performance system offers the latest 802.11ax ‘Wi-Fi 6’ technology.
With Wi-Fi being the de facto wireless data communication technology of choice for consumers, Calix engineered the GigaSpire BLAST u4 for optimal whole-home coverage with simultaneous dual-band 2.4 GHz and 5 GHz operation and dynamic beamforming. Leveraging the latest Wi-Fi 6 features, the BLAST u4 provides longer range, higher efficiency and less interference compared to earlier generations of Wi-Fi technology.
GigaSpire BLAST u4 Key Attributes - BLAST u4 Home Gateway Layer 2 bridge and Layer 3 routing for High Speed Internet (HSI) data and IPTV video services DHCP server options DHCP (IPoE) and PPPoE network connections Network Access Translation (NAT), public to private IP addressing Configurable IP address schemes, subnets, static-IP addresses DNS server Bridge port assignment and data traffic mappings Port forwarding Firewall and security Application and website filtering Sele
WI-FI 2.4 GHz and 5 GHz, simultaneous dual-band 2.4 GHz and 5 GHz 802.11ax (Wi-Fi 6) certified, 802.11a/n/ac compatible 4x4 streams (2x2 @ 2.
IGMP Fast Leaves Gateway Management: CSC (Calix Support Cloud) TR-069 Local Home Gateway GUI, access provisionable Remote WAN side GUI access Default username/password AC to 12 VDC power adapter Proprietary Information: Not for use or disclosure except by written agreement with Calix. .
GigaSpire Mesh BLAST u4m Overview The Calix GigaSpire Mesh BLAST u4m is the new generation Wi-Fi 6 mesh satellite that complements the Calix GigaSpire family of products. With the broad portfolio of GigaSpire smart home systems, BLAST® u4m extends Wi-Fi coverage and capacity within the subscriber’s home. The BLAST® u4m Wi-Fi 6 backhaul allows communications service providers (CSPs) to deploy satellites with either a wired or wireless connection to the GigaSpire. When connected wirelessly, the 5.
MULTI-GIGABIT SUBSCRIBER EXPERIENCE The GigaSpire Mesh BLAST® u4m is a high performance wireless satellite that delivers the latest 802.11ax Wi-Fi technology in a consumer friendly form factor. Subscribers want their Wi-Fi to work with any device in any location throughout their home. Over time, the numbers, types and locations of these devices has exploded.
Market research projects that tens of billions of residential IoT devices will be deployed in the coming years. The GigaSpire and GigaMesh provides powerful Wi-Fi to support the growing IoT deployment. Service providers can now deploy the BLAST u4m with plug-andplay Wi-Fi IoT devices such as security cameras, sensors, and smart plugs. EASY TO INSTALL, ACTIVATE AND MAINTAIN With the GigaMesh satellites, Calix has redefined how to install and activate residential services.
WPS push-button 2x2 DL/UL MU-MIMO with beamforming 1024 QAM; OFDMA; BSS Coloring Support for 802.11k/r/v/s o 11k Radio Resource Management 11r Fast Roaming 11v Wireless Network Management Support 4-address WDS mode Support 16 SSID Replication per band 1.
Agency Listing FCC WARNING: These devices comply with Part 15 of the FCC Rules and Regulations. Operation is subject to the following conditions. This device may not cause harmful interference, and, this device must withstand any interference received, including interference that may cause undesired operation. The ONT has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules and Regulations.
Proprietary Information: Not for use or disclosure except by written agreement with Calix. .
Site Preparation Before you install any GigaSpire BLAST device, you need to consider the routing of the power adapter cord and Ethernet cable(s) if used. Note: It is critical that you maintain the proper airflow in and around the unit. GigaSpire BLAST devices are designed for surface mounting only. Do not install cabinetry or other building material around the outside of the unit.
Introduction This document describes the installation of the following: GigaSpire BLAST u4 GigaSpire Mesh BLAST u4m The BLAST u4 and u4m are designed to be placed in a horizontal table-top configuration or can be wall mounted using the mounting holes molded into the back of the unit. Powering Options By attaching to any 110/220 VAC power outlet using the supplied 12 VDC wall transformer.
Tabletop or Wall Mount - u4 8295 Reset GE WAN 10/100/1000 USB 2.0 Power Adapter Type A Power On/Off G-Ethernet LAN x2 10/100/1000 Tabletop or Wall Mount - u4m 8294 Reset GE WAN/LAN 10/100/1000 Power Adapter Power On/Off LED Power Supply (2-Pin) Proprietary Information: Not for use or disclosure except by written agreement with Calix. .
Proprietary Information: Not for use or disclosure except by written agreement with Calix. .
Chapter 2 Installation Installation Tips CAUTION! Use of controls or adjustments or performance of procedures other than those specified here may result in hazardous radiation exposure. ! Follow these tips when installing a GigaSpire device: For subscribers using data services, all data wiring inside the home must be CAT5e cable or better. Make sure subscriber connections are tightened properly. Check the contents of each box carefully as you receive them.
Building Materials and Their Effect on Wi-Fi Signals Material Wi-Fi Attenuation Wood, Drywall, Particle Board, Tile Low Glass Low Water Medium Bricks, Cinder Block Medium Plaster, Stucco High Concrete High Tinted or Low-E Glass (metalized) Very High Metal Very High lower the attenuation, the better the performance. Installation Variables Before installing the GigaSpire BLAST u4 or Mesh BLAST u4m, consider what additional services may be implemented.
GigaSpire BLAST u4m 8294 Reset GE WAN/LAN 10/100/1000 Power Adapter Power On/Off LED Unpacking the GigaSpire u4/u4m Each GigaSpire BLAST u4 or u4m is shipped individually in its own carton and contains the following: (1) GigaSpire BLAST u4 or (1) GigaSpire Mesh BLAST u4m (1) Power Adapter interface cord (wall wart) (1) Safety and Regulatory Statements Guide (2) Product Identification Labels with Login Credentials After opening the carton, remove the protective packaging, ensure all componen
Tabletop Mounting Dimensions Dimensions are shown here for your reference. BLAST u4/u4m 5.0 “ 12.7 cm 8292 1.5 “4 cm Proprietary Information: Not for use or disclosure except by written agreement with Calix. .
Wall Mounting Dimensions Dimensions for wall mounting of a GigaSpire BLAST u4 or Mesh BLAST u4m are included here for reference. Note: There is no wall mount bracket necessary to mount these devices. The bottom chassis itself includes appropriate cut-outs and hanger posts to facilitate wall mounting. GigaSpire u4 or u4m Mounting Dimensions 5.0 “ 12.7 cm 2.5 “ 6.35 cm 8297 2.5 “ 6.35 cm Tabletop Mounting the u4/u4m Any Calix GigaSpire BLAST u4 or u4m can be mounted flat on a tabletop.
Wall Mounting the u4/u4m The Calix GigaSpire BLAST u4 and the GigaSpire Mesh BLAST u4m can be wall mounted using. Keep the following information in mind when considering wall mounting: Locate the BLAST on the wall in a location that is unlikely to be bumped or jostled. Make sure that the Ethernet cable(s) (if used) and power supply wiring attached to the GigaSpire are secured properly and out of harms way.
Additional Mounting Considerations The options for mounting a GigaSpire BLAST system are many. From a best practices standpoint, keep the following in mind: Calix recommends mounting the BLAST as high as possible for Wi-Fi performance reasons. However, this deployment scenario still mandates that an AC power outlet is located within the power cord distance of the Wi-Fi source.
Proprietary Information: Not for use or disclosure except by written agreement with Calix. .
Chapter 3 Final Set-up and Testing BLAST u4/u4m Reset Behavior Calix EDGE systems support a variety of system reset functions and provide multiple methods for invoking each of these functions, as described in this topic. Calix defines these functions and behaviors as follows: 1. Basic reset (reboot): Restarts the router. 2. Configuration reset: Resets the RG configuration settings (those visible to the subscriber/Admin user in the EWI, such as SSIDs, LAN IP scope, etc.
These reset functions can be used as troubleshooting and/or operations tools for reset/removal scenarios, whether the device is deployed as a Residential Gateway or as a subtended WAP or Satellite (GigaSpire BLAST or GigaMesh). Hardware-invoked resets behave differently depending on how long the reset button is pressed, as described below.
Powering the BLAST u4/u4m The information below describes the powering of any GigaSpire BLAST. To power up the BLAST u4 or u4m 1. Locate the 12 VDC Power Adapter. 2. Attach one end (2-pin barrel connector) to the rear of the BLAST u4/u4m. 3. Plug the other end into any available 110/220 VAC wall outlet. 4. The GigaSpire BLAST begins its start-up sequence (Flashing blue LED).
Connecting to the Internet The method by which the GigaSpire BLAST u4 or GigaSpire Mesh BLAST u4m is deployed will impact the internet connection. With power applied to the BLAST, perform the following steps based on the role the device plays in the network. Connecting to a residential gateway If the unit is configured as a Residential Gateway, connect an Ethernet Cable to its WAN port from the WAN modem (ONU, cable modem, or DSL modem).
LED States - Power Off & Boot-up Note: For all LED sequences, the BLAST u4 and the Mesh BLAST u4m incorporate a single LED located on the interface side of the unit. Power Off and Boot-up Description Colors Indication OFF Power is Off The unit has not been turned on or Off There is no power to the unit or Any auxillary battery has been discharged and can no longer power the unit.
LED States - Samsung Smart Things Samsung Smart Things Description ST Hub Ready for Setup Red & Green Flashing Colors Indication LED green and Red cycles at 500 msecs.
LED States - Mesh Mode Mesh BLAST u4m with BLAST u4 Description GS202xE Mesh Satellite (Backhaul pairing cycle can be started by WPS button press [3+ second press] or equivalent EWI or smartphone app activation) Colors Indication For backhaul pairing press WPS for at least 3 seconds N/A Booting Up or SW Upgrade in Process Unit is in the process of being boot up or service/software is being upgraded Flashing every 1 second on cyan color - assuming SW can control the LEDs.
After pairing, follow the Gateway Status After the pairing is complete (60 seconds after the signal strength has been displayed), the light bar indication shall follow the Gateway status as described on the Light Bar tab in this spreadsheet. If the mesh is connected via Ethernet connection, if boot up successfully, the light bar indication shall follow the Gateway status as described on the Light Bar tab in this spreadsheet.
Wall Mount Template Inside the giftbox of the BLAST u4 or u4m, a printed wall mount template is included. This template is scaled to size and should be used when marking the hole locations for the wall mount option. The figure below is a representative example of the template but should not be used as it is not scaled appropriately. For additional information, refer to Wall Mounting the u4/u4m (on page 28) located in the Installation chapter of this guide.
Proprietary Information: Not for use or disclosure except by written agreement with Calix. .
