RCD277DBT Bluetooth/CD/MP3/SD/MMC/USB Player with DAB+/FM/AM tuner Operation Instructions
Contents Safety Information Thank you for purchasing this product. Please read this manual carefully before operating and reserve it for future reference. ———————————————————— PRECAUTIONS • Use only in a 12-volt DC negative-ground electrical system. • W hen replacing the fuse, be sure to use one with an identical amperage rating. Using a fuse with a higher amperage rating may cause serious damage to the unit. • DO NOT attempt to disassemble the unit.
Panel Controls Power on : Press any button on the panel except 14 to turn on the unit. 13 12 11 TA 1 AF 2 PTY 10 9 3 1. - Power on - Mute - Press more than 2 seconds to power off. 2. - Radio tune - Track skip/seek 3. - Press to pop out/push back the knob. - Rotate the knob to adjust volume level. 4. - Radio - Disc play (when disc inserted) - Card (when SD/MMC card inserted) - USB (when USB inserted) - AUX-in - BT music(when BT connected) - DAB 5.
Other Instructions Press the button to open the panel and press 1 2 3 to eject the disc. 4 5 1. - Disc eject 2. - Reset hole Note: Pressing the RESET hole will erase the clock setting and stored stations. 3. - Panel status indicator Lights up when you flip the panel down; Twinkles when you remove the panel. 4. - Disc slot, insert the disc. 5.
Remote Control Operating range Point the remote control unit to the remote sensor when you operate with it. The remote control can operate within a distance of 3~5m. Remote Sensor MUTE SRC VOL SEL AMS MENU TA 1 / TOP SEARCH AF/REG PTY BAND 2 3 4 INT RPT RDM 5 6 DISP 1. 2. 3. 4. - Power on/off - Volume - Mute - Press to select VOL/BAS/TRE/BAL/FAD, use volume button to adjust level. - Press and hold it to enter Menu mode. 5. - Traffic announcements identification 6.
USB/SD/MMC MP3 Playback Anti-Theft 1. Loading SD/MMC Card button to flip down the panel, insert Press the SD/MMC card into the slot, with the front side at left. Close the panel, the unit will play the music automatically. 2. Take out SD/MMC Card Press SRC button and switch to non CARD mode, open the panel, slightly press the card, take out the card when it was popped out. 3.
General Operation Power On/Off Button Press the MUTE/ button to turn the unit on when the vehicle ignition switch is on. Long press to turn the unit off. ———————————————————— Adjust Volume level Rotate the VOL knob to adjust volume level. Rotate it clockwise to increase and anticlockwise to decrease the volume.
Radio Operation ress BAND button to select radio band as P follows: FM1, FM2, FM3, WM1, WM2 RDS service availability varies with areas. Please understand if RDS service is not available in you area, the following service is not available. TUNE RDS Basics Band Switch MANU SEEK: Press or to tune step by step. A UTO SEEK: Press or more than 2 seconds to seek automatically. Store Station Manually Press button 1 - 6 more than 2 seconds to store current station.
Radio Operation DAB Operation is updated by EON data. EON enables the radio to make fuller use of RDS information. It constantly updates the AF list of preset stations, including the one that currently tuned into. If you preset a station around the area at your home, you will later be able to receive the same station at an alternative frequency, or any other station serving the same program, EON also keeps track of locally available TP stations for quick reception.
MP3 Playback While playing MP3 disc/USB/SD/MMCMP3 MUSIC, the folder/file name and ID3 TAG (Song title, Album and Artist) can scroll entirely across the LCD. Press the button BAND to show ID3 information: Elapsed playing time & Track number -> Folder name & number -> File name & number -> Song title -> Album title -> Artist name ———————————————————— Direct Song/File Access 1. P ress the AMS button once and press MENU button to enable direct track searching. 2.
MP3 Overview • The unit support multi-session disc with MIXED & EXTRA format, but plays the MP3 tracks is priority. MIXED format: disc structure first is MP3 data, second is audio data. EXTRA format: disc structure first is audio data, second is MP3 data. • T h e u n i t s u p p o r t a l l M P E G b i t r a t e including free format for MPEG 1 audio layer 3, support all MPEG bit rate except 8kbps and free format for MPEG 2 audio layer 3. • T h e u n i t s u p p o r t 3 2 / 4 4 .
Bluetooth Operation Note: For your safety, avoid talking on the phone as much as possible while driving. Bluetooth is a wireless transmission way for short distance. The built-in Bluetooth can connect with the mobile phones having Bluetooth function. After connecting, you can control your mobile phone through the unit. Pairing Use this function to establish a connection between the unit and your mobile phone. 1. Turn on the unit. 2.
Menu Function Bluetooth Operation Music Mode A2DP A2DP is short for Advanced Audio Distribution Profile. The mobile phones supporting this function can transmit stereo audio, whereas the ones not supporting this function can transmit mono audaio only. AVRCP AVRCP is short for Audio/Video Remote Control Profile. The mobile phones supporting this function can control the playback of a Bluetooth audio player. General Notes for Bluetooth 1.
Menu Function TA VOL Rotate the knob to adjust TA volume. RETUNE mode RETUNE mode: Rotate the knob to choose RETUNE-S or RETUNE-L. RETUNE-S or RETUNE-L is time length selection of TA SEEK retune interval. RETUNE-S: short, TA SEEK retune interval is 45 seconds. RETUNE-L: long, TA SEEK retune interval is 180 seconds. Remark: RETUNE mode functions for TA during TA SEEK mode only.
Electrical Connections Wiring Diagram (Black) (Black) Antenna (Black) Rear line out (Gray) Location 1 2 3 4 5 6 7 8 Function Connector A Battery 12V(+) / Yellow ANT/AMP control / Blue with white stripe ACC+ / Red Ground / Black Microphone SWC (Steering Wheel Control) Connector B Rear Right (+) / Purple Rear Right (-) / Purple with Black Stripe Front Right (+) / Gray Front Right (-) / Gray with Black Stripe Front Left(+) / White Front Left(-) / White with Black Stripe Rear Left (+) / Green Rear Left
Installation Guide Installation Procedures First complete the electrical connections, and check for correctness. ———————————————————— Reset Install the unit Important: Remove the two screws on the top of the unit before installation. Otherwise, the player will not work. Installing the panel • • Press button to flip down the panel. Then press the RESET button with a pointed object to reset the unit to the original status.
Troubleshooting If you suspect something is wrong, immediately switch power off. Do not use the unit in abnormal condition, for example without sound, or with smoke or foul smell, can cause fire or electric shock. Immediately stop using it and call the store where you purchased it. Never try to repair the unit yourself because it is dangerous to do so. General No power or no sound. Radio Much noise in broadcast. Preset station lost. Car’s engine switch is not on. Cable is not correctly connected.
Specifications General AM(MW) Radio Power supply Frequency range 522 – 1710KHz Usable sensitivity(S/N=20dB) 30dBμ ——————————————————————————————— 2V DC(11V-16V) Test voltage 14.4V, 1 negative ground Max.current consumption 12A Maximum power output 50Wx4 channels Continuous power output 20Wx4 Suitable speaker impedance 4-8ohm Pre-Amp output voltage 2.0V (CD play mode: 1KHz, 0dB, 10KΩ load) Fuse 15A Dimensions(WxHxD) 178x50x166mm Weight 1.
PN: 127075003363