Installation & Assembly

ManualsBrandsCadet ManualsElectric Space HeatersCom-Pak Series Energy Plus Multi-Watt 120/240-Volt Electric Fan Wall Heater

cadetheat.com

855.CADET.US

Vancouver, Washington

tested to UL standards

MORE COMFORT, LESS ENERGY

OWNER’S GUIDE

COM-PAK

http://cadetheat.com/install/energyplus

For how-to videos or more information, please visit:

ESPAÑOL ver la guía del propietario en cadetheat.com/espanol/energyplus

Thank you for your purchase! Question or problem? Let us solve it with

a single phone call, email or online chat! We’ll save you a trip back to

the store!

Phone: 855.CADET.US (855.223.3887)

email: customerservice@cadetheat.com

Live chat: cadetheat.com (contact us)

Cadet Customer Service

Summary of content (8 pages)

PAGE 1
OWNER’S GUIDE COM-PAK MORE COMFORT, LESS ENERGY Thank you for your purchase! Question or problem? Let us solve it with a single phone call, email or online chat! We’ll save you a trip back to the store! Cadet Customer Service Phone: 855.CADET.US (855.223.3887) email: customerservice@cadetheat.com Live chat: cadetheat.com (contact us) For how-to videos or more information, please visit: http://cadetheat.com/install/energyplus ESPAÑOL ver la guía del propietario en cadetheat.
PAGE 2
IMPORTANT INSTRUCTIONS When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1. Read all instructions before install- 6. To disconnect heater, turn control(s) to off, and turn off power to heater ing or using this heater. circuit at main disconnect panel. 2. This heater is hot when in use. To avoid burns, do not let bare skin 7. Do not insert or allow foreign touch hot surfaces.
PAGE 3
INSTALLATION INSTRUCTIONS ® 1. All electrical work and materials must comply with the National Electric Code (NEC), the Occupational Safety and Health Act (OSHA), and all state and local codes. 2. Use copper conductors only. 3. DO NOT install the heater directly above bathtub or sink. DO NOT install in shower stall area. Cadet recommends installing your heater at least 2 feet (61 cm) away to prevent contact with water. 4.
PAGE 4
¾" (1.9 cm) Min. 4 PARED ADYACENTE INSTALLATION INSTRUCTIONS TIPS BEFORE YOU BEGIN • Verify power has been turned off before starting any work! • The Energy Plus can only be mounted with the element up. It cannot be mounted in the ceiling or in the ﬂoor. For multiple heater wiring, see page 6. • For cleaner performance and longer heater life, install your heater 12 inches from the ﬂoor. • All models can be installed to be Americans with Disabilities Act (ADA) compliant.
PAGE 5
INSTALLATION INSTRUCTIONS INSERT THE HEATER ASSEMBLY IN THE WALL CAN STEP 4 Wire connections 1. Your heater has two connection wires on the side. Your supply wire has two connection wires and a supply ground wire. wall can A. Connect supply ground wire to grounding screw in wall can (See Figures 3 and 4). B B. Connect one supply wire to one heater wire with a wire connector (not included). For 240 or 208 volts, it doesn’t matter which heater wire. Both supply wires (black and white) are hot.
PAGE 6
INSTALLATION INSTRUCTIONS MULTIPLE HEATERS ON ONE CIRCUIT BREAKER (240 or 208 volts only) More than one heater can be wired in parallel on the same circuit breaker (be sure to check national and local codes for safety requirements). Additional electrical supply wire and cable clamp connectors are required. The heaters must be in the same room. Maximum amperage you can put on one circuit breaker is limited to 80% of the circuit breaker capacity. 1.
PAGE 7
OPERATING INSTRUCTIONS 1. Make sure all wires are properly connected and installation is complete before you turn on the heater. 2. Do not operate without grill. 3. Do not tamper with the high-temperature safety shutoff. Complete installation After installation, turn your heater to the highest setting and let it run for 30 minutes. Some smoking may occur as the element initially burns off residue from manufacturing.
PAGE 8
MAINTAINING YOUR HEATER Clean heater at least every 6 months or as required. Do not lubricate motor. 1. Turn off power at the main disconnect panel. 2. Wait for the heater to cool. 3. Remove grill. 4. Wash grill with hot soapy water and dry. 6. Clean the fan with a vacuum cleaner. 7. Replace grill. 8. Turn power back on at the main disconnect panel. 5. Blow air through the heating element with a hair dryer or shop vacuum on blow cycle.