Installation Guide
cadetheat.com Tel: 855.CADET.US PO Box 1675 Vancouver, WA 98668-1675
SAVE THESE INSTRUCTIONS
Apex72 Decorative Cover
Instructions
WARNING! Before removing or installing outlet grill, turn the electrical power off at the
main disconnect panel (circuit breaker or fuse box). Lock or tag the main disconnect panel
door to prevent someone from accidentally turning the power on while you are working on
the heater. Failure to do so could result in serious electrical shock, burns, or possible death.
Important Information
Installation
STEP 1
Install Metal Outlet Grill
Install outlet grill onto heater assembly. Slide the two tabs on the left side of the outlet grill into the two slots on the left side of the heater
assembly (Figure 1). Then insert the small tabs at the top and bottom of the outlet grill into place (Figure 2). Attach with ⅜" #6 black
outlet grill screw provided.
STEP 2
Install Decorative Cover
The decorative cover is held in place with permanent magnets. If desired, the cover can be further
secured with the two ½" #8 retention screws provided (Figure 3). Attach retention screws at top and
bottom of decorative cover only after the outlet grill has been installed on the heater assembly and
attached with the screw provided (Figure 2).
Turn power on at the main disconnect panel.
Please see your specic product Owner’s Guide for additional installation, operation and mainte-
nance instructions for both decorative cover and heater. (Owner’s Guides may be downloaded at
cadetheat.com).
Warranty
The Apex72 decorative cover includes four neodymium magnets. Neodymium magnets have extremely
strong magnetic elds. Should magnets detach from the plastic cover, handling them with care is
necessary to prevent personal injuries.
CADET
Model: HW 108
Volts: 208 60Hz
Watts: 1000
447 Mfg Date: 19-Jan-15
3108579
Conforms to
UL STD 2021
WARNING!
High temperatures may
be generated under cer-
tain abnormal conditions.
Do not partially or fully
cover or obstruct the front
of this heater.
Use only with Cadet wall
can Model CC
UP!
070352C
CADET
Model: HW 108
Volts: 208 60Hz
Watts: 1000
447 Mfg Date: 19-Jan-15
3108579
Conforms to
UL STD 2021
WA RNING!
High temperatures may
be generated under cer-
tain abnormal conditions.
Do not partially or fully
cover or obstruct the front
of this heater.
Use only with Cadet wall
can Model CC
UP!
070352C
TOOL REQUIRED: • Phillips Screwdriver
INCLUDED IN THIS BOX:
• Decorative Cover
• (1) ⅜" #6 Black Outlet Grill
Screw
• Hexagonal or Louvered
Outlet Grill
• (2) ½" #8 Retention
Screws
http://www.cadetheat.com/products/wall-heaters/apex72
Information is also available on our website:
For more effective and safer operation and to prolong the life of the heater, read the
Owner’s Guide and follow the maintenance instructions. Failure to properly maintain
the heater will void any warranty and may cause the heater to function improperly.
Warranties are non transferable and apply to original consumer only. Warranty
terms are set out below.
LIMITED FIVE-YEAR WARRANTY: Cadet will repair or replace any Apex72 (ACL
or ACH) decorative cover found to be defective within ve years after the date of
purchase.
These warranties do not apply:
1. Damage occurs to the product through improper installation or incorrect supply
voltage;
2. Damage occurs to the product through improper maintenance, misuse, abuse,
accident, or alteration;
3. The product is serviced by anyone other than Cadet;
4. If the date of manufacture of the product cannot be determined;
5. If the product is damaged during shipping through no fault of Cadet.
6. The use of unauthorized accessories or unauthorized components constitutes an
alteration and voids all warranties. Refer to Cadet website or call customer service
at 855.CADET.US for list of authorized accessories and components.
7. CADET’S WARRANTY IS LIMITED TO REPAIR OR REPLACEMENT AS SET
OUT HEREIN. CADET SHALL NOT BE LIABLE FOR DAMAGES SUCH AS PROP-
ERTY DAMAGE OR FOR CONSEQUENTIAL DAMAGES AND/OR INCIDENTAL
EXPENSES RESULTING FROM BREACH OF THESE WRITTEN WARRANTIES
OR ANY EXPRESS OR IMPLIED WARRANTY.
8. IN THE EVENT CADET ELECTS TO REPLACE ANY PART OF YOUR CADET
PRODUCT, THE REPLACEMENT PARTS ARE SUBJECT TO THE SAME WAR-
RANTIES AS THE PRODUCT. THE INSTALLATION OF REPLACEMENT PARTS
DOES NOT MODIFY OR EXTEND THE UNDERLYING WARRANTIES. REPLACE-
MENT OR REPAIR OF ANY CADET PRODUCT OR PART DOES NOT CREATE
ANY NEW WARRANTIES.
9. These warranties give you specic legal rights, and you may also have other
rights which vary from state to state. Cadet neither assumes, nor authorizes anyone
to assume for it, any other obligation or liability in connection with its products other
than as set out herein.
If you believe your Cadet product is defective, please contact Cadet Manufacturing
Co. at 855.CADET.US, during the warranty period, for instructions on how to have
the repair or replacement processed. Warranty claims made after the warranty
period has expired will be denied. Products returned without authorization will be
refused.
Parts and Service
Visit cadetheat.com/parts-service for information on where to obtain parts and
service.
Reduce-Reuse-Recycle
This product is made primarily of recyclable materials. You can reduce
your carbon footprint by recycling this product at the end of its useful
life. Contact your local recycling support center for further recycling
instructions.
Retention
Screw
©2015 Cadet Printed in USA Rev 06/15 #720123
Figure 3
Figure 1 Outlet grill attaches to heater assembly
Louvered outlet grill installed
Figure 2
½" #8
Retention
Screw
Secure outlet
grill here with
⅜" black outlet
grill screw
½" #8
Decorative
Cover
Outlet
Grill