EID-2 Optical Impression Device Operation Manual iTero Mobile Cart Publication SD08300-A Revision 1.10 April 18, 2007 Optical Impression System for Computer Assisted Design and Manufacturing (510K exempt under 21 CFR 872.
EID-2 Optical Impression Device Operation Manual COPYRIGHT Copyright © by Cadent. 1995-2007. All rights reserved. The hardware and software described in this document are supplied under a Sales and Services Agreement and may be used only in accordance with the terms of that agreement. The information contained in this document is subject to change without notice.
Operation Manual EID-2 Optical Impression Device SYMBOLS Caution! - Wherever this symbol appears on the device, it is recommended to refer to the instructions in this Operator’s Guide. Applied part type B. Any component on which this symbol appears is electric isolation type B. CLASS 1 LASER COMPLIANCE Class 1 Laser Product This product complies with “21 CFR 1040.10” and “EN 60825-1”.
EID-2 Optical Impression Device Operation Manual WARNINGS POWER An internal battery backup unit will supply AC power to the system in the event of a power shortage. Therefore, power is present in the internal hardware components even when the system is unplugged from the wall. To ensure that power is removed from all components, follow these instructions: Close all files and applications. Press the front POWER switch to shutdown the system.
Operation Manual EID-2 Optical Impression Device Table of Contents Chapter 1: Introduction .......................................................................................................... 7 Overview ................................................................................................................................ 7 The Digital Crown Production Process ................................................................................... 7 About the iTero Service .......................
EID-2 Optical Impression Device Operation Manual This page is intentionally blank. 6 Publication SD08300-A (Rev. 1.
Operation Manual EID-2 Optical Impression Device Chapter 1: Introduction Overview The EID-2 functions as a digital impression system for scanning preparation teeth in the doctor’s office and uploading the digital files to Cadent for further processing and CNC crown production. This Operator’s Guide explains how to operate the system, and also describes the system’s hardware components and features. Chapter 1: Introduction Overview of the iTero digital crown production process.
EID-2 Optical Impression Device Operation Manual About the iTero Service Cadent’s iTero service has introduced to the dental industry a breakthrough technology in the field of digital crown production. The iTero technology makes it possible to perform an intra-oral digital scan in the office and to produce a precise crown based on the digitally acquired data.
Operation Manual EID-2 Optical Impression Device Front Features Basic hardware features are shown below. See Chapter 2 for detailed operating instructions. Flat LCD monitor can be swiveled freely in any direction. Optical scanner for capturing teeth images. Note that the scanner may be placed in scanner cradle in either direction (right-to-left or left-to-right). POWER switch for boot and shutdown. Optical mouse Built-in keyboard Hook for holding scanner cable off the floor.
EID-2 Optical Impression Device Operation Manual Back Features Basic hardware features are shown below. See Chapter 2 for detailed operating instructions. Air Vent (do not block) Air Vent (do not block) Main AC Power Cable 10 Publication SD08300-A (Rev. 1.
Operation Manual EID-2 Optical Impression Device Chapter 2: Operating Instructions This chapter describes the essential operating instructions for booting or shutting down system. First Time Usage (1) (2) (3) Plug the power cord into the wall socket. Press the “MAIN POWER SHUT OFF” button on the rear of the cart. System will beep to indicate presence of power. Leave the system plugged in for at least 24 hours.
EID-2 Optical Impression Device Operation Manual Automatic Shutdown When the cart is unplugged or a power outage occurs, a warning beep will begin. If the system is left unplugged for several minutes, warning messages will appear on the screen and will also be heard through the speakers. As the minutes pass, the status of the battery backup unit will be displayed on the screen. When the battery backup unit is nearly empty (after about 10 minutes), the system will automatically shut down.
Operation Manual EID-2 Optical Impression Device Chapter 3: Cleaning and Maintenance This chapter describes how to clean and maintain the various hardware components. Foot Pedal Unit USING THE PEDALS The foot pedal unit contains two pedals for responding to screen questions during scanning. The colors of the two foot pedals match the Pedals dialog in the iTero OFFICE application (red on left, green on right). CHECKING BATTERY Pressing either foot pedal turns on the green LED.
EID-2 Optical Impression Device Operation Manual Disinfecting Scanner and Replacing Disposable Sleeve To avoid cross contamination, it is essential that after each patient you disinfect the scanner and replace the disposable plastic sleeve. First use disinfectant wipes to clean the scanner arm, scanner cradle, keyboard and mouse. Then proceed with the steps below to replace the sleeve. STEP 1 Press firmly on both sides of the disposable sleeve to release it.
Operation Manual EID-2 Optical Impression Device Cleaning Monitor (1) Shut down the system using the front POWER switch to ensure that no power is being supplied to the monitor. (2) Lightly dampen a clean white cotton cloth with water and wipe monitor clean. (3) Dry the monitor immediately using a clean white cotton cloth. (4) If further cleaning is necessary, use a clean cloth to wipe off the monitor with a small amount of alcohol.
EID-2 Optical Impression Device Operation Manual Appendix A: Hardware Specifications ITEM DESCRIPTION Monitor LCD 19” monitor meets FCC and safety approval (UL, CSA, TUV) and operates at 1280x1024 resolution. Handheld Scanner Scanner emits red laser light (660 nm Class 1) as well as a multi-colored LED light. Battery Backup Unit Wireless LAN APC® Back-UPS® ES 725 Broadband DWL-G122™ Wireless USB Adapter produced by D-LINK®. The DWL-G122 provides 2.4 GHz communications using the 802.
