FD702XW HGU Products 1GE+1FE+WIFI+CATV User Manual Version：V1.1 Company Address: Room 601, Floor 6, Building F, Songbai Road 1008, Sunshine Community，Xili Street, Nanshan District, Shenzhen(518108) Factory Address: Fl1, Bldg B, Wentao Industrial zone, Yingrenshiyongxin Village, Shiyan Street, Baoan district, Shenzhen, Guangdong, China (518055) Tel: +86-755-26014509/4710/4711 Fax:+86-755-26014506 Website: www.cdatatec.
FCC compliance statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Content 1 Note ................................................................................................................................................ 1 1.1 Installation Precautions ....................................................................................................... 1 1.2 Precautions for Use ............................................................................................................. 1 2 Brief .......................................................................
11 TR069 Remote Management ..................................................................................................... 25 11.1 Configure Channel for TR069 Remote Management...................................................... 25 11.2 TR069 Client Configuration ............................................................................................ 25 12 Device Management .................................................................................................................. 26 12.
1 Note 1.1 Installation Precautions Do not place the equipment near flammable or conductive items, high temperatures (such as direct sunlight) or in wet conditions, or on a PC chassis, and check that the surrounding appliances are stable. Check the cable for aging. Check and verify that the AC or DC input voltage is within the permissible range of the device and that the polarity of the DC is correct.
To ensure safety, do not open the enclosure of the device, especially when the device is powered up. Unplug the power supply before cleaning the equipment. Use a soft dry cloth to clean the equipment to avoid the use of liquids or sprays. Do not connect this product to any electronic product unless it is instructed by our customer engineer or your broadband supplier, as any incorrect connection may cause power or fire hazard.
2 Brief Realtek series XPON ONU is satisfying with Telecom, Radio and Television, and Fiber To The Home (FTTH) multi service access. It’s based on the mature, stable, high cost performance EPON/GPON technology and has Gigabit and Fast Ethernet switching HFC technology, WLAN technology and powerful routing forwarding technology.
⚫ 2.2 Light reflection loss: >45dB Product Operation Introduction The dual-mode ONU is a "combination" of GPON and EPON ONU. Compared with the single- mode EPON/GPON ONU, the main difference lies in the registration process. The dual-mode ONU adds a pre-judgment to the current application system (EPON/GPON). That is, the dual-mode ONU first switches mode, and then starts and completes registration process in the corresponding mode.
2.
2.7 Applications 3 Login Web Management Locally 3.1 Physical Connection of ONU and PC a) Local NIC of PC connects to LAN port or ETH port of ONU via wires. b) Set the IP address of PC’s local NIC as 192.168.101.X (X：2-254). c) Open cmd windows and make sure that PC can ping the management IP (192.168.101.1) of ONU.
3.2 PC Access the WEB of ONU Make sure you can ping the ONU like #3.1. Open the IE Web broswer (IE, Firefo x, Google), copy and paste URL: http: //192.168.101.1, the following pop-up Prompt landi n-g page: Input UserName：adminisp PassWord： adminisp Click “Login” button.
You can start further configuration. 4 ONU Register Information Config(When adaptive to GPON mode) 4.1 View ONU Register Status 1. Login ONU WEB, select Status -> Internet Info -> GPON Info, view the ONU register status： 4.2 View ONU Optical Power Information 1.
4.3 LOID Authentication Config LOID of ONU is mainly applicable of the authentication mode of LOID and LOID + Password for ONU. By default, ONU registers for the OLT by SN and rarely uses LOID for register. Normally, we needn’t to configure LOID. But the configuration as follows: 1. Login ONU WEB, select Internet -> Remote Mgmt -> LOID, view or configure LOID and password of ONU： 5 ONU Register Information Config(When adaptive to EPON mode) 5.1 View ONU Register Status 1.
5.2 View ONU Optical Power Information 1. Login ONU WEB, select Status -> Internet Info -> GPON Info, view Rx power and Tx power of ONU： 5.3 LOID Authentication Config LOID of ONU is mainly applicable of the authentication mode of LOID and LOID + Password for ONU. By default,EPON ONU registers for the OLT by MAC and rarely uses LOID for register. Normally, we needn’t to configure LOID. But the configuration as follows: 1.
Home Gateway Unit (HGU) ONU supports route function, so that there are route mode and bridge mode for internet. The difference between route mode and bridge mode as follows : Route mode：ONT as a home gateway equipment, ONT IP address can be obtained in three ways, which includes DHCP, Static IP Address and PPPoE.
【Bind port】Bundel the physical ports (Lan port 1-4 and wireless) with PPPoE WAN connection. Note: By default, all LAN ports and WIFI data are not bound by this WAN connection (a LAN and WIFI SSID can only be bound to a WAN conection at the same time). 2.
6.1.2 Configure DHCP WAN Connection for Internet in Route Mode 1．Login ONU WEB, select Internet -> Internet Config -> Internet Config, and then there are some parameters for us to configure as follows: 【WAN Connection name】Select ‘Add WAN Connection’ 【Mode】Select ‘ Route ’ 【 Connection Mode 】 Select ‘Ipv4’; If there is Ipv6 in the network, we can select ‘ Ipv4/Ipv6 ’.
LAN and WIFI SSID can only be bound to a WAN conection at the same time). 2.After configuring the parameters of DHCP WAN connection as belows, click ‘Apply’ to finish the setting： 6.1.
【WAN Connection name】Select ‘Add WAN Connection’ 【Mode】Select ‘ Route ’ 【 Connection Mode 】 Select ‘Ipv4’; If there is Ipv6 in the network, we can select ‘ Ipv4/Ipv6 ’. 【Internet way】Select ‘Static’ 【NAT】Check ‘ NAT ’ feature；NAT is mainly used for address translation function of local network and external network. The default is checked enable status. If you do not check this option, maybe you can’t surf the internet. 【Enable Vlan】We can set this option according to your network plan.
2. After configuring the parameters of Static IP WAN connection as belows, click ‘Apply’ to finish the setting： 6.
【WAN Connection name】Select ‘Add WAN Connection’ 【Mode】Select ‘Bridge’ 【Connection Mode】Select ‘Ipv4’; If there is Ipv6 in the network, we can select ‘Ipv4/Ipv6’. 【NAT】 Don’t check ‘NAT’ feature；NAT is mainly used for address translation function of local network and external network. HGU ONU doesn’t deal with the packets from the teminal, so we needn’t enable the NAT function. 【Enable Vlan】We can set this option according to your network plan.
2. After configuring the parameter of Bridge WAN connection as above, click ‘Apply’ to finish the setting： 6.3 View the WAN Connection Status 1．Login ONU WEB, select Status -> Internet Info -> IPv4 Status. In here, we can view WAN connection status, check the route WAN connection if it gets an IP address and Bridge WAN connection if it is UP. As follows: 6.4 Delete the WAN Connection 1．Login ONU WEB, select Internet -> Internet Config -> Internet Config.
7 ONU LAN Configuration 7.1 LAN IP Address Configuration 1．Login ONU WEB, select Internet -> DHCP Server -> IPv4 DHCP Server, and then there are some parameters for us to configure as follows: 【 IP address 】 Set local management IP address of ONU. The default IP address is 192.168.101.1 【Subnet mask】Set the mask of local management IP address of ONU 【Disable DHCP Server/Enable DHCP Server】Enable or disable ONU DHCP Server function.
7.2 View LAN Client 1．Login ONU WEB, select Status -> LAN & WLAN -> WLAN Status. View client that access via wireless (WIFI). As follows: 2．Login ONU WEB, select Status -> LAN & WLAN -> LAN Status. View client that access via LAN ports . As follows: 8 Multicast/IPTV Configuration 8.1 Multicast/IPTV Service Setting Firstly, configure a bridge WAN connection to carry IGMP/IPTV service according to #6.2 and select ‘Other’ in service mode.
8.2 IGMP Snooping Setting 1．Login ONU WEB, select Application -> IGMP Config -> IGMP Snooping. Enable or disable IGMP Snooping function and click ‘Save/Apply’ button to finish the setting as follows: 8.3 IGMP Proxy 1．Login ONU WEB, select Application -> IGMP Config -> IGMP Proxy.
9 WLAN Configuration 9.1 WLAN Basic Configuration 1. Login ONU WEB, select Internet->WLAN Config->WLAN Config, and then there are some parameters for us to configure as follows: 【Enable wireless】Enable or disable the wireless function； 【Virtual SSID】Click ‘Virtual SSID’ button to enter the virtual SSID config page； 【Band】The default is 2.4GHz（B+G+N）； 【SSID】Set wireless SSID name. Nowadays, it doesn’t support to set as Chinese SSID name.
2. After setting wireless configuration, click ‘Save/Apply’ button to finish setting. 9.2 WLAN Password Configuration 1．According to #8.1, click ‘Advanced’ button to enter ‘Wireless settings-Security’ page, we can set ‘Network authentication mode’ , ‘encryption’ and WIFI password. 2．After setting wireless password configuration, click ‘Save/Apply’ button to finish setting. 9.
2．After setting wireless password configuration, click ‘Save/Apply’ button to finish setting. Note: we can refer to #8.2 about setting the password of virtual SSID. 10 CATV Configuration CATV management is mainly applied to ONU with light machine, we need to configure the ONU optical machine parameters through the ONU’s WEB. 10.1 Configure CATV Port Parameter Select Management→CATV conifg→CATV config.
11 TR069 Remote Management ONU TR069 remote management is mainly used for some network that support TR069 server centralized remote management, the current management is mainly used in many large networks, ONU as TR069 remote management of the client need to do the following settings. 11.1 Configure Channel for TR069 Remote Management Firstly, refered to #5.1, set a Route WAN connection with ‘Service mode’ as TR069, which is used to act as a channel for TR069 server. 11.
12 Device Management 12.1 ONU Remote Access Configuration Login the ONU WEB, select Management -> Wan Access Control -> Wan Access Control. In this page, we can enable or disable the ping remote access and WEB remote access of ONU. 12.2 Restore Default Setting Login the ONU WEB. Select Management -> Device -> Restore ONU. Click ‘Restore Default Setting’ button. The device will restore the factory defaults after the application.
Note:Restore Setting on the ONU WEB is take effect to WIFI information of ONU and LAN port configuration only. It doesn’t take any effect to WAN connection. 12.3 Firmware Upgrade Login the ONU WEB. Select Management -> Firmware Upgrade -> Firmware Update. Click ‘选择文件’ to select firmware file, click ‘upgrade’ button to upgrade the ONU. After the application, the device is upgraded to the latest software version. Note: We needn’t extract Realtek project production’s firmware, just upgrade the .tar file.
Concluding Remarks Thanks for using products of Shenzhen C-Data Technology Co. Ltd. Contact Information: Company Address:Room 601, Floor 6, Building F, Songbai Road 1008, Sunshine Community，Xili Street, Nanshan District, Shenzhen(518108) Factory Address: 1st floor, Building B, Wentao Industrial Park, Yingrenshi Community, Shiyan Avenue, Baoan District, Shenzhen, China Telephone: 0755-26014509/26014710/26014711 Fax: 0755-26014506 Email: Marketing@cdatatec.com Website: www.cdatatec.com www.cdatatec.com.
