User Manual

ManualsBrandsC. D. V. I. ManualsElectronicsProximity Reader

DGPROX

PIN Code and/or Badge

STAND-ALONE PROXIMITY SYSTEM

32 V1 E M B OCT5 12

RL1RL2

ST1 ST2

1 3

PB1

Input voltage

12V ~ or =

230V~

strike

12 V 1 4 5 3 2

Wiring diagram

PCB front view

This device comes with a varistor.

The varistor must be connected on the strike terminal

(electromagnet…) operated by the device.

If this product operates more than one strikes, each of them

should have a varistor.

The varistor controls the overload produced by the strike coil –

back emf.

B Request-to-exit PB1

E Alarm Input

M Common PB1, E and 4

O Relay 1 contact

C Common

T Relay 2 N/O contact

I1 Anti-tamper switch

V1 Varistor

ST1

ST2

Jumper for reset

Jumper for relay 1

RL1 Door relay

RL2 Alarm relay

12 Power

supply

V Po

wer supply

1 Data

2 Buzzer

3 Green LED

4 Common M

Auxiliary reader

(terminal connections)

Warning

Do not use a

switching

power supply

because of the

interference

radiation that

may disturb

the reading of

the badges

N/C contact RL1 (magnet)

N/O contact RL1 (strike)

See wiring diagram auxiliary reader

ST2

1 3

If you are using a « Shear Lock » electromagnetic lock, it is recommended to use a

separate power supply than the one connected to the DGPROX.

Summary of content (9 pages)

PAGE 1
DGPROX PIN Code and/or Badge STAND-ALONE PROXIMITY SYSTEM Wiring diagram PCB front view ST2 1 1 3 N/C contact RL1 (magnet) 3 N/O contact RL1 (strike) ST1 I1 3 2 1 Warning Do not use a switching power supply because of the interference radiation that may disturb the reading of the badges RL2 strike 2 1 V1 230V~ B E M O C T I1 V1 ST1 ST2 RL1 RL2 ST2 1 Request-to-exit PB1 Alarm Input Common PB1, E and 4 Relay 1 contact Common Relay 2 N/O contact Anti-tamper switch Varistor Jumper for reset Jum
PAGE 2
Technical features Input voltage Output Anti-triggering contact Badge entry Code entry Master code Input Keyboard Distance between the second reader and the DGPROX unit 12 VAC/DC 2 relays, N/O & N/C contact 3A /125V 500 mA 50 V ~ or = 500 programmable badges 500 programmable codes, 5-digit PIN code 5-digit programmable code 1 request-to-exit 12-digit keypad with built-in buzzer (audible signal) minimum 24 inches (60 cm) maximum 45 yards (50 meters) (cable minimum 7 x 0.
PAGE 3
Setting a new master code Enter the master code twice (for the first use, the master code default is 12345). 2 beeps will sound and the orange LED illuminates to confirm that you are in programming mode. Enter *3 then 5-digit for the new master code. The LED goes out for 1 second and an audible beep indicates that the new master code is accepted. Press # to exit from the programming mode. 2 beeps confirm that the reader is in standby mode. 4 beeps indicate a data computing error.
PAGE 4
Canceling or replacing programmed user codes and badges Enter the master code twice (for the first use the master code default value is 12345). 2 beeps and the orange LED light on to confirm that you have entered into the programming mode. Enter the user number (000 to 499). The LED lights off during 1 second and an audible beep is emitted. The red LED lights on indicating that the user number is unavailable. Press the * key twice (**). The LED lights off during 1second and an audible beep is emitted.
PAGE 5
User number Name User number Time delays Name User Number Name Function n° Values Keypad key-in delay Door relay *0 *1 « opened door » before alarm *2 Master code *3 10 = 10 sec, 99 = 99 sec 01 = 1 sec, 99 = 99 sec 00 = without alarm 01 = 10 sec, 99 = 990 sec 5-digit code Supervisor : Name Programmed values Date : Building : N° : User number Street : City : Other information : 5
PAGE 6
Wiring diagram auxiliary reader DGPROX ST1 I1 3 2 1 RL2 2 1 1 2 3 M 5 ST2 1 3 RL1 E M B 3 5 T C O 12 V Distance : minimum 60cm maximum 50 m 12 V 1 Reader 12 V 1 2 3 4 5 Power supply Power supply Data Buzzer Green LED Common Red LED It is recommended to use a separate power supply for the auxiliary reader.
PAGE 7
Template • DGPROX Wiring Access Area 137 mm 125 mm 110 mm 29 mm 26 mm 31 mm 30 x 40 mm 22 mm 45 mm 68 mm 86 mm 7
PAGE 8
PAGE 9
Template • DGLI and DGLP Auxiliary reader 75 mm 25 mm Block terminal 43x15 mm 6 mm ] 60 96 mm mm FCC statement: NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.