Edition 01/2001 G0301GB0089V01 UCA/3 -1 - 3-DOOR CONTROL UNIT WITH BUILT-IN RF RECEIVER WIRING DIAGRAM AND INSTRUCTIONS Wave λ/4 17,3 cm receive antenna or antenna at 50 Ω Wiring diagrams at the end of the user manual This device comes with a varistor. The varistor must be connected to the strike terminal (electromagnet…) operated by the device. If this product works with many strikes, each of them should have a varistor. The varistor controls the overload produced by the strike coil – back emf.
Edition 09/2000 Technical specifications Input voltage Outputs Users Master badge Memory RF receiver Inputs Présentation Distance between the readers and the control unit 12 V AC or DC 3 relay outputs, N/O & N/C contact 8A/250V~ 800 badges (proximity and RF Transmitter) 1 programmable proximity badge Capability to transfer copy all data on a other control unit Built-in RF receiver on the control unit 2 Request-to-exit inputs 3-digit 7 segments display 4 programming keys minimum 60 cm, maximum 50 m (recomm
Edition 09/2000 Programming mode --- Main menu Present a proximity badge in front of the control unit proximity reader. ----- If the master badge is not programmed in the control unit, present any proximity badge wait for the display to switch off and then press on the PROG button to enter in the programming mode. ----- If the master badge is programmed Main menu Present the master badge in front of the control unit reader, wait for the display to switch off and press on the PROG button (red button).
Edition 09/2000 3. Keep the jumper on to delete all the badges. 4. The display indicates during the reset. 5. The display switches off at the end of the reset. 6. Remove to jumper from the ST1. Setting and deleting badges (Menu 1) Proximity Badges: Proximity badges can be programmed on door 1 and 2. DOOR 1: controlled by reader 1 DOOR 2: controlled by reader 2 Once the door is selected (door 1 and/or door 2) in Menu 1 all the badges entered in the control unit will have the same door configuration.
Edition 09/2000 2nd choice: To program the RF Transmitter press on Nxt to move to the next choice The display indicates door 1 and 3 can be programmed with RF Transmitter. To get back to the previous display press PRV button.
Edition 09/2000 Available user number Present the badge in front the control unit proximity reader to program the badge on door 1 and /or door 2. To program the RF Transmitter, press on one of the remote button. if the badge is already programmed; this message is displayed during 2 seconds. Present another badge. Once the badge is saved, the user number s stays displayed during 2 seconds.
Edition 09/2000 Press Ent button to change the open time for relay 2 and enter a time from 01 second to 99 seconds. Enter 00 for a latched output time. Then press Ent button to save the new time. Press Nxt or Prv to select another door time relay and press Ent button to modify the time. The third time relay indicates a default value of 1 second for relay 3. Press Ent button to change the open time for relay 3 and enter a time from 01 second to 99 seconds. Enter 00 for a latched output time.
Edition 09/2000 The following message is displayed on the Control Unit which transmit the data On the other Control unit the message is displayed. Press Ent button start the transmission. Once the transfer is completed this message seconds. appears on the two Control Units during 5 Connection ERROR between control units If the two Control Unit are not connected properly an error message is displayed Verify the wiring and try again.
Edition 09/2000 Badge and RF Transmitter Identification (Menu 5) ? The display is off. The 5th LED is on. Present the badge in front of the Control Unit proximity reader or press on one the button of the RF Transmitter. The display indicates Door 1 the badge is identified as 271 as the user number.
Edition 09/2000 Template 75 mm Proximity reader 60 mm 96 mm Channe1 Channel 2 RF code number 010030BC8D 000002F5C7 Proximity Code Number 10
Edition 09/2000 Block terminal 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 V1 V2 V3 Input voltage Input voltage Input voltage Input voltage Reader 2 green LED Reader 2 common PB2 Reader 2 data N/C contact relay 1 Common relay 1 N/O contact relay 1 N/C contact relay 2 Common relay 2 N/O contact relay 2 Reader 1 green LED Reader 1 common PB 1 Reader 2 data N/C contact relay 3 Common relay 3 N/O contact relay 3 GND Data transmission Data receiving Receive Antenna 433 MHz(optional) Re
Edition 09/2000 Wiring Diagram 17.
Edition 09/2000 Wiring diagram with proximity readers L1 25 26 L2 L3 L4 L5 PROG N P E ST1 RL1 1 2 230 V 3 4 5 6 7 RL2 RL3 Proximity Reader 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Input voltage12V 12 V 1 4 5 3 2 Proximity reader 2 12 V 1 4 5 3 2 Proximity reader 1 13
Edition 09/2000 Wiring diagram with a keypad L1 25 26 L2 L3 L4 L5 PROG AV AR V ST1 RL1 1 2 3 4 5 RL2 Proximty Reader RL3 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Wiring between KCP – UCA3 230 V Input voltage 12V ~ or = KCP Reader1 White Brozn Yellow Grey 14 3 4 18 16 UCA3 Reader2 3 4 8 6 1 2 3 4 5 6 7 8 9 Ý 0 #
Edition 09/2000 Wiring diagram with a magnetic stripe reader L1 25 26 L2 L3 L4 L5 PROG AV AR V ST1 RL1 1 2 3 4 5 6 7 RL2 RL3 Proximty Reader 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Wiring between D534 – UCA3 Module 230 V 1 2 3 4 5 6 Input voltage 12V ~ or = UCA3 Reader1 Reader2 NC 15 18 16 3 4 NC 5 8 6 3 4 6 5 4 3 2 1 Interface Module D534 7 8 9 10 111213 Brown Grey Yellow w Orange Green White 15
Edition 09/2000 FCC statement: NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
