User's Manual

ManualsBrandsC-Compact ManualsElectronicsC-Compact

Table Of Contents

User Manual C-Compact

FCC Part 15 complient notice for product variant 62 (North America)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

 (1) this device may not cause harmful interference, and

 (2) this device must accept any interference received, including interference that may cause

undesired operation.

Changes or modifications not expressly approved by Convadis AG could void the user's authority

to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

To comply with FCC RF exposure compliance requirements for an uncontrolled environment, «C-

Compact» main unit must be installed to provide a separation distance of at least 20 cm from all

persons.

This Transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter.

INDUSTRY CANADA (IC) complient notice for product variant 62 (North America)

Convadis AG, Stroppelstrasse 20, CH-5417 Untersiggenthal, Tel + 41 56 290 35 45, info@convadis.ch, www.convadis.ch 1/10

Summary of content (10 pages)

PAGE 1
User Manual C-Compact FCC Part 15 complient notice for product variant 62 (North America) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:  (1) this device may not cause harmful interference, and  (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by Convadis AG could void the user's authority to operate the equipment.
PAGE 2
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:  This device may not cause interference.  This device must accept any interference, including interference that may cause undesired operation of the device.
PAGE 3
 LTE-M: 1(2100 MHz), 2(1900 MHz), 3(1800 MHz), 4 (1700 MHz), 5(850 MHz), 8(900 MHz), 12(700 MHz), 13(750 MHz), 18(850 MHz), 19(850 MHz), 20(800 MHz), 25(1900 MHz), 26(850 MHz), 28(700 MHz)  FCC US: Band 2,4,5,12,13,25, 26  ISED CANADA: Band 2,4,5,12,13,25               HW ready to assemble alternate cell phone modules o 2G/3G, 4G NB-IoT, 5G module from the same supplier. Integrated cell phone antenna GNSS module (GPS/GLONASS,GALILEO, BAIDU). A-GPS with integrated antenna.
PAGE 4
Installation: The unit includes a 10 pin conector with multiple hw configurable signal routing options and an additional connector for connectiong remote keys of the car (for lock/ unlock and for immobilizer function on cars with keyless start system). For easy connecting to the vehicle harness (12V power and data) a connector to the On Board diagnostic connector or the vehicle (OBD) is avaialble.
PAGE 5
C-Port includes an immobilizer option for for vehicle types with keyless go systems (start button instead of ignition lock switch), as well as for transponder immobilizer systems. Inserting the SIM card, place and install the main unit and connect the cables: The SIM card (Nano-SIM) is inserted under the main print. Before inserting, the device must be disconnected from the power supply by unplugging the main plug. Press briefly at the little notch to remove the SIM.
PAGE 6
Main cable three: Pin 1 2 Color Standard signal green Immobilizer 2 output pink Alternate signals    Analog fuel input LIN bus +3V out   Immobilizer 1 output +3V out Analog fuel input 3 grey CAN1 Lo  CAN FD Lo 4 yellow *CAN1 Hi  CAN FD Hi 5 blue Odometer pulse input  CAN2 Lo 6 black Ignition on detect  CAN2 hi  7 white 8 orange    Unlock (Separate lock/unlock, no feedback line) Permanent feedback (common lock/unlock on Pin 8) Lock (Separate lock/unlock, no feed
PAGE 7
lock/unlock on Pin 7) 9 red Power Supply + 10 brown Ground Immobilizer: Direct connection to «Immobilizer 2» wire of main OBS cable tree: The immobilizer output «Immobilizer 2» (main cable tree Pin 1, green wire) contains a self protective FET to connect a wire to ground, e. g. the wire from the start button of a the car can be connected to ground via this wire. The OBS will switch the ground connection off in «logged out» state to immobilize the car then.
PAGE 8
Pin Color Signal 1 red Unlock 2 orange Lock 3 yellow Reference voltage in 4 green 3V power for Remote control battery 5 blue Remote Control battery ground Mounting the parts It is critical that the mounting position of the unit is in accordance with the local government standards in the operational region of the vehicle. Mounting of the components on the windshield is only allowed at specific locations, mainly the corners (Europe: EU standard 77/649/EWG).
PAGE 9
Please make sure, that the unit is fixed securely to not become loose, even during a crash. Please clean the mounting place with alcohol before taping it onto the glass. I The device is including a high frequency cell phone antenna and other RF antennas and therefore it must be placed at least 20 cm away from the passenger body in its usual position. Please also locate it 20 cm away from sensitive electronic parts and wires of the vehicle and from any other RF antenna.
PAGE 10
- Now tap the job in the vehicle list in the smartphone. It will now be sent to the vehicle. The LED now lights up green. - The device now establishes a connection to the CCom server and obtains the previously defined vehicle-specific device configuration from there. If necessary, the firmware on the device is also updated (duration approx. 10 minutes). Status messages appear in the app. - At the end the LED goes out. "Synchronization complete" is displayed in the app.