Quick Manual

Marking
SPEED
LED/FLIP
RESET
PAIR
▲ F
◀ L
POWER
▶ R
▼ B
Pressed Briefly
Change Speed
Change LED Color
Trim Pitch +
Trim Roll -
Trim Roll +
Trim Pitch -
Pressed Long
Take-Off/Landing
Rotate 360 (Roll or Pitch)
Reset sensor (Zero bias,Trim initialization)
Pairing
HEADLESS ON
MODE 1
Power ON/OFF
MODE 2
HEADLESS OFF
LED ON LED Dimming
Disconnected
LED Blinking Twice
Connected Headless - Normal Connected Headless - Headless
* If the drone does not have a battery,
the buzzer sounds on the controller
and the LED on the drone flashes.
1. It is recommended that you use the product for users over the age of 8.
It is recommended that first-time users be familiar with the manual and use it with sufficient practice.
2. The drone's propeller is so fast that it always requires attention and can cause physical and property damage.
For your safety, always maintain a certain distance from the drone.
3. Manufacturers and vendors are not responsible for accidents due to poor operation.
4. Fly in normal weather conditions with temperatures between 50 ℉ and 122 ℉.
5. For operational and repair inquiries, please contact your place of purchase.
● Make sure the battery is fully charged.
● Make sure the propeller is correctly installed.
● Make sure that the control and the drones are connected as normal.
● Make sure there are no obstructions in the area.
● Practice the drones first for take-off and landing and emergency stop functions.
● Use a distance of more than 2 meters from the drone.
1. Disconnect the battery out of the drone. The included charging via the charger usb.
2. charging, the charging is completed, and indicators illuminated indicator will extinguish.
1. Power On/Off / Reset Sensor
Press and hold the power button in the middle of the controller for more than 3 seconds to turn it on and off.
With the drone connected, press and hold the reset button to reset the sensor for the drone.
2. Throttle Lever & Directional Lever
Once the drone is connected to the controller, it can begin to operate the drone
For instructions on how to control each lever, see How to control a drone.
3. Trim Adjustment (F/B/L/R Button) & Mode 1/2 Change
To stabilize a drone during flight if it is tilted in either front/rear/left/right direction:
Press the F (front)/B (back)/L (left)/R (right) trim button to operate.
You can change the mode using the L (left) and R (right) buttons when you are not in the flight
4. Speed · Start/Stop (SPEED · START / STOP)
Press the button briefly to change the speed of the drone. (Step 1: Beep 1 / Step 2: Step 3)
Press and hold the button for more than 3 seconds to automatically take off and land the drone.
5. Headless mode · pairing (HEADLESS · PAIR)
When not in flight, press and hold the F button to activate the headless mode; press and hold B button to release.
You can perform pairing by pressing and holding the PAIR button for more than 3 seconds when it is not in flight.
6. LED · Flip (LED · FLIP)
Press the button briefly to change the LED on the drone to the desired color.
During flight, when the LED · Flip button is pressed and the directional lever is moved, the drone rotates 360 degrees.
7. Status Indication
When the drone is disconnected, the LEDs on the drone and the controller flash and beep.
If the drone's battery is low, only the LEDs on the drone will flash and the controller will beep.
*For more information, see
the detailed description
section of each function.
Activate the 'headless mode' for beginners.
The 'headless mode' is fixed in the direction of the drone's operation, regardless of the direction of the drone's front
or rear.
'Headless mode' On when the LED on the controller flashes by pressing and holding the F button while landing
'Headless mode' off when the controller's LED illuminates brightly by pressing and holding the B button while landing.
CAUTION: 'Headless mode' on/off can only be changed when landing; it cannot be changed during flight.
When the headless mode is turned on by pressing the button, the direction the drone is facing is fixed forward.
Settings allow you to change to mode1 or mode2.
Pressing and holding the Ltrim button for more than 3 seconds while landing mode1
Pressing and holding the RTRIM button for more than 3 seconds while landing mode2
Caution: the default state is set to mode2 and if you change the mode,
Be sure to familiarize yourself with the operation of that mode before flying.
You can start/stop the motor when it is not in flight.
Push both levers simultaneously as shown in the image and
hold for at least 2 seconds.
In the event of an emergency situation during flight, the emergency stop function can be used to stop the motor
of the drone.
Press and hold the speed start/stop button and press the throttle lever down to make an emergency stop.
CAUTION: If the emergency stop function is used, the motor will stop and fall in the air, so the drone may be damaged.
Only operate the function in an emergency.
Be sure to familiarize yourself with the following methods before operating the drone.
Poor steering requires a lot of practice because it can cause damage and injury.
1. Set the front and rear sides of the drone apart and place it on a flat.
2. Press the controller's automatic take-off/landing button for more than 3 seconds to initiate drone flight.
* Make sure you have enough free space before turning
360 degrees.
Press and hold the LED/FLIP button on the right side of
the detector to hear a beep.
Push the right-hand lever in the desired direction and the
drone rotates 360 degrees in that direction.
If the drone is tilted to one side after the trim setting, or the drone does not fly normally, proceed
to reset the sensor. With the drone and the controller connected, place the drone on a flat floor
and press and hold the controller reset button to proceed with sensor reset.
Drone during the sensor reset led starts blinking, reset is complete, the brightly lit again.
When the start button is
pressed and held, the controller
will continuously beep.
1. Place the drone on a flat surface and prepare for flight.
2. Press the automatic take-off/landing button of the controller for more than 3 seconds
to take off.
3. The drone hovers.
4. During flight, press and hold the automatic take-off/landing button on the controller for
more than 3 seconds to land.
Please also be familiar with the emergency stop function in case of emergency.
1. Use the right-hand lever to slowly push forward/backward to
practice front/backward control in the air.
2. Practice pushing the levers slowly to the left and right,
as shown above.
1. Slowly raise the left throttle lever to maintain altitude in the air.
2. Adjust the throttle lever to maintain constant altitude and slowly slide the throttle lever
to the left or right to rotate.
If not in headless mode, the drone rotates and changes direction, so be aware of your flight.
Once you are familiar with the preceding "practicing," practice your
flight with a combination of fine-tuning and fine-tuning the various
commandments in the air.
Before flying a drone, note
1.Before flying drones, always look around.
2. Fly within the user's vision.
3.The child should fly the drone from where the parents are looking.
4.When using multiple drones at the same time, be careful with the frequency.
* Be sure to check all items regularly before flying. Replace, repair and operate after damage.
* Recharge using the charger provided.
* Be sure to turn off and remove the power when removing dust from the product.
* Do not randomly change the structure of this product.
* Recyculate battery or battery packs or dispose of them correctly according to waste disposal methods.
* Be sure to turn off and store the power of the drones and the controls when storing.
* Do not throw or drop drones and controls.
* Read and familiarize yourself with the handling manual.
Precautions
Precautions to Know Before Flying a Drone
Do not fly drones in the following circumstances
Near signal towers and
high voltage power lines
Crowded Place
Thunder and Lightning Weather
Near Rail and Airport Unauthorized Public Places Forest and River Windy Weather
1xDrone
1xController
1xBattery
1xUSB Charger
1xMicro 5-pin Cable
1xPropeller
Guide
1xManual
Basic Component Guide
Name by Drone Part
CCW Propeller (B)
CW Propeller (A)
Housing
Frame
CCW Motor
CW Motor
Lithium Battery
Main Board
Rubber Damper
Pilot Guidance
: When Pressed Briefly : When Pressed Briefly
Insert Controller Battery
*Open the battery cover.
Insert battery for polarity (+/-) indication.
Close the battery cover.
Caution:
A. Make sure the battery is inserted to the polarity mark.
B. Remove discharged batteries and do not use batteries
of different types.
Connecting Drone
Plain Floor
A swing of more
than 10 times
faster
Pressing for more
than 3 seconds
1. Connecting the Controller to the Drone
When the drone's battery is connected, the drone's LED flashes.
Put the drone down on a flat floor and turn the controller on.
A beep will be heard and paired automatically.
* Important: The controller and the drone are basically paired.
The battery is automatically paired when connected and powered on.
You do not need to perform a pairing every time.
2. New Connecting the Controller to the Drone
If no drones and controls are connected, or if a new control
and connection is required, new drone pairing is carried out.
1. Within 20 seconds of connecting the drone's battery,
hold the drone in your hand and shake it quickly to enter
pairing mode.
(The LED flashes red/blue quickly when in pairing mode)
2. Put the drone in pairing mode on the floor and turn
on the controller.
3. Pair the drone by pressing the PAIR button on the controller
for more than 3 seconds.
4. When 4 drones are connected, a beep is heard and the LED
color is fixed.
Precautions
The pairing mode can only be entered within 20 seconds of the
battery connection and after 20 seconds the drone's battery
must be reconnected.
Pilot Main Function Guidance
How to operate a drone (Mode2)
Throttle
Rotation
Forward and backward movement
UP
Down
Left Right
UP
Down
Right and Left movements
Left Right
Rise
Fall
Left turn
Right Trun
Forward
Reverse
Move Left
Move Right
* The drone rises when the throttle
lever is raised and falls down when
the throttle lever is lowered.
* If the throttle lever is lowered and
landed on the ground during the
flight, the motor will stop.
* Turn the 'throttle lever' of the
controller to the left, and the
drone turns left.
And Turn the 'throttle lever' of the
controller to the right, and
the drone turns right.
* Push forward the directional lever
of the controller to move the drone
forward.
And push reverse the directional
lever of the controller to move the
drone reverse.
* Push the directional lever of the
controller to the left to move
the drone to the left
And Push the directional lever of
the controller to the Right to move
the drone to the Right
Motor Start/Stop
or
Emergency stop
Headless Mode
Change Mode
Mode 1
Mode 2
Rotate 360 degrees (Mode)
Rotate Forward: up the rudder.
Rotate Back: Turn the Directional
Levers Down
Left Rotation: The rudder is left.
Right Rotation
: The directional lever to the right
Left Rotation
Right Rotation
Rotate
Forward
Rotate
Back
Once familiar with the above three steps, practice a combination of precision control
flights by simultaneously manipulating the three phases in the air.
Propeller Repacement
Battery Charging
A = Clockwise Yellow Propeller
Direction
(rear)
B = Counterclockwise White Propeller
B = Counterclockwise Yellow Propeller
A = Clockwise White Propeller
To Charge
Precautions
A continuous beep sound from the controller during flight indicates that the drone's battery
is running low. Charge the battery after landing.
Battery Precautions
Connect to the adapter or PC to charge
Drone Battery: Please comply with the regulations for the use of lithium batteries.
Controller Battery: The controller requires two "AAA" batteries.
Please read the precautions below carefully.
● Do not use any other type of battery.
● Do not use with a discharged battery.
● Do not charge disposable batteries.
● Take care when charging the battery.
● View the polarity indicator (+/-) and insert correctly.
● Do not heat the battery or put the battery in the fire.
Precautions
LED Display information Charging specification
LED Off LED ON
Charge Complete Charging
Input Charging current
Maximum
Voltage
Battery Capacity and Charging Specifications
Battery Type Battery Capacity
Lithium Battery
Time of Use
Maximum flight time of 5 minutes
Charging time
40 Minutes
(approximately 0.5 Amps)
Guides and caveats for first-time users
Precautions
1. To practice take-off and landing
2. To practice throttle lever
1. Place the drone on a flat surface and prepare for flight.
2. Press the automatic take-off/landing button of the controller
for more than 3 seconds to take off.
3. The drone hovers.
4. During flight, press and hold the automatic take-off/landing button
on the controller for more than 3 seconds to land. Please also be
familiar with the emergency stop function in case of emergency.
3. To practice directional control (Mode2)
4. Practice of rotation (Mode 2)
5. Precision Control Exercise
6. Trim
Take off the drone in a windless environment to see if it is flowing in the air.
1. Forward/Reverse Moving Trim: When a drone flows forward
in the air without any operation
Press the B button on the controller to adjust the trim.
Conversely, if it flows backwards in midair without any control,
press the F button on the controller to open the trim. Adjust it.
2. Left/Right Trim: When a drone flows from the air to the left
without any operation Press the R button on the controller
to adjust the trim. Conversely, if you're moving in midair to
the right, press the L button on the controller. Adjust the trim.
NOTE: The controller will beep whenever the trim button is pressed.
Once the maximum value of the trim setting is reached, there will
be no more beeps. If normal flight is difficult even with trim setting, reset the drone sensor.
(Press the drone on a level surface and briefly press the controller's power button to reset the sensor.)
Forward
Reverse
Left
Right
7. Rotate 360 degrees (Mode2)
Stable and easy 360 degrees of rotation
8. Sensor Reset
Precautions to Know Before Flying a Drone
Basic Component Guide
Name by Drone Part
Pilot Guidance
Insert Controller Battery
Pilot Main Function Guidance
Connecting Drone
How to operate a drone (Mode2)
Motor Start/Stop
Emergency stop
Headless Mode
Change Mode
Rotate 360 degrees (Mode)
Periodically check the propeller status of the drones and replace them with new ones if damaged/damaged.
1. The drone has four propellers. Among them, yellow represents the front.
2. Refer to the image and make sure that the direction of rotation is the matching propeller.
3. IMPORTANT: Normal flight is not possible if the propeller is not in the correct direction.
Propeller Repacement
To Charge
Guides and caveats for first-time users
Troubleshooting
Initial Defect and Warranty
Troubleshooting
Initial Defect and Warranty
Supports the following initial defect and warranty exchange policies:
1. Within 7 days of receipt of the new product
2. If problem symptoms are found within 5 minutes of the cumulative flight time after opening the product;
If a problem occurs with a product that meets all of the above conditions, it will be judged to be an initial
defect and you will be able to exchange the product.
Any other user negligence and damage other than initial defect will result in paid repair, so please note.
Please contact your place of purchase for further product repair and support.
* Drone simulator, Rocket Brick for Cordonrobolinksw.com
* Check the website later for coding manual. (robolink.co.kr )
Problem
Cause
Solution method
I plugged in the drone's battery
and it just blinks and becomes
unresponsive
The drone and the controller
are out of pairing
There is no response when
connecting the drone's battery
The motor won't stop when I
lower the lever to land
Only the propeller turns and
the drone does not take off
The drone rotates in place even
after the trim is set
The drone doesn't fly after
the crash
The battery is running low
I didn't know if the drone was
on the floor
1. the direction of the propeller
is wrong
2. the battery is low
1. the direction of the propeller
is wrong
2. The propeller is damaged
3. Sensor reset is required
I plugged in the drone's battery
and it just blinks and becomes
unresponsive
Refer to the manual and cycle
power to both the drone and
the controller and try new pairing
Please charge the battery
of the drone
Please raise it up again and try to land
Lower and hold the throttle lever for at
least 2 seconds after the drone hits the floor
1. Fit the propeller in the correct
orientation
2. Charge the battery
1. Refit the propeller correctly
2. Replace the propeller
3. Refer to reset sensor in manual
1. Refit the propeller
2. Replace the propeller
Autonomous safety
check report number
Quick Manual for Control