Manual NÜO FLUX 41762 | 42039
NÜO Flux Manual Information Features GENERAL FEATURES NÜO FLUX (ref. no.: 42039 and 41762) -- Maximum security proximity reader for 13.56 MHz contactless MIFARE® Plus, MIFARE® DESFire EV1, MIFARE® Classic and MIFARE Ultralight® cards. -- Reader status indicated via acoustic-light display. -- Communication encrypted with AES AND 3DES encryption algorithms. -- IP65 protection. -- Operating temperature from -20 °C to 50 °C for indoor and outdoor installations.
NÜO Flux Manual Information Features TECHNICAL SPECIFICATIONS NÜO FLUX: INPUT VOLTAGE 24VDC (11 - 28 VDC) POWER 1.8 W CPU 32-bit ARM Microprocessor READING DISTANCE 5 - 8 cm MAXIMUM POWER 250 mA COMMUNICATIONS 2 twisted pairs.
NÜO Flux Manual Information Features TECHNICAL SPECIFICATIONS READER DIMENSIONS 92 x 92 x 30 mm (height x width x depth) READER DIMENSIONS WITH EMBEDDED 92 x 92 x 57 mm (height x width x depth) CASE EMBEDDED CASE DIMENSIONS 82 x 82 x 52 mm (height x width x depth) -- Embedded case -- Suction cup to remove front glass panel -- Bag with accessories: ACCESSORIES -- Screws to fasten reader to the embedded case. -- Screws, washers and nuts for surface mounting.
NÜO Flux Manual Installation NÜO FLUX TYPE OF WIRING AND WIRING DISTANCE: The NÜO FLUX readers incorporates a 4-pin male overhead connector and the corresponding female connector which joins 3 metres of piped cable with 4 wires (2 twisted pairs). This means that the installation and wiring to then connect the reader to a single door controller or to the corresponding Wili are both very simple.
NÜO Flux Manual Installation NÜO FLUX Installation on built walls The NÜO FLUX reader can be flush mounted in various environments. The various installation methods are described below, covering built walls, plasterboard walls, and integration into other equipment such as turnstiles or gates: 1. Installation on working surfaces: 1) Using a level, make a hole in the wall for the rear case measuring 82 x 82 mm and 52 mm deep. Do not forget to pass the reader cable through.
NÜO Flux Manual Installation 2. NÜO FLUX Installation on plasterboard walls Installation on plasterboard walls 10 to 22 mm thick: 1) Using a level, make a hole in the wall for the rear case measuring 82 x 82 mm. Do not forget to pass the power and communication cables through. 2) Place the case in the hole and screw the pressure tabs to fix the case to the wall. These tabs apply pressure against the wall as the screws are turned. 82 Place the magnet at the top. This magnet will work as a tamper.
NÜO Flux Manual Installation 3. NÜO FLUX Installation in other environments Installation in other environments: 1) Using a level, create a niche on the surface where the reader is to be placed measuring 78 x 78 x 30 mm. Create 4 holes forming a square measuring 80 x 80 mm for M3 screws. You can use tapped holes in order to avoid having to use nuts. 2) Remove the NÜO FLUX reader front glass panel using the suction cup supplied. Place the suction cup in a corner for ease of operation.
NÜO Flux Manual Installation Wiring NÜO FLUX readers can be directly connected to two types of devices depending on facility architecture: -- Connection to a Wili. -- Connection to a single door controller. The connection to be made for both types of devices is exactly the same. The colour code must be followed. For more detailed information, consult the equipment manuals referenced earlier. Respect the specified input voltage.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipmentÿ Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.