BURR KING MFG. CO., INC MODEL 960-250 INSTRUCTION MANUAL 1220 Tamara Lane Warsaw, MO 65355 www.burrking.
BURR KING MFG. CO., INC. 1220 TAMARA LANE WARSAW MO 65355 WWW.BURRKING.COM (660) 438-8998 (800) 621-2748 FAX (660) 438-8991 June, 2007 Burr King Manufacturing Company. Inc. warrants the below product to be free in material and workmanship. The period of warranty is 1 year (90 days for vibratory bowls of 20 quart and lesser volume) from the date of purchase.
BURR KING MFG. CO., INC. 1220 TAMARA LANE WARSAW MO 65355 WWW.BURRKING.COM (660) 438-8998 s (800) 621-2748 FAX (660) 438-8991 June 21, 2007 LETTER OF AUTHENTICITY This letter is to certify that all Burr King Belt grinders, Disc grinders, Polishing machines Vibra King Chambers and Bowls are manufactured and assembled in the United States of America. (Tariff number 847990 criterion A) Don Mac Carthy President See our catalog at www.burrking.com contact us at info@burrking.
BURR KING MFG. CO., INC. 1220 TAMARA LANE WARSAW MO 65355 WWW.BURRKING.CO M (660) 438-8998 s (800) 621-2748 FAX (660) 438-8991 February 2005 OPERATOR, and OPERATING AREA SAFETY Subject equipment includes Grinders, buffers, polishers, and other rotating equipment. Serious injury or death may occur if minimum safety precautions are not understood, and obeyed by operators and those other persons who may be in the immediate vicinity of the subject equipment.
Continued from page 1 of the work rest (or table) will permit passage of the work piece through the gap (nip point). Note, however, that certain alloys such as titanium may create conditions where grinding debris can accumulate in a tight gap creating a potential fire hazard. When in doubt consult with your safety officer. Failure to observe this warning may result in the work piece or other item being caught in this gap, and/or being forcibly ejected.
Continued from page 2 Occupational Noise Exposure Burr King products produce levels of noise consistent with their intended purposes. The level and spectral content of noise produced is dependent on the product type, the degree that the product is maintained in proper operating condition, the abrasive/media and accessories used, the specific application, and the surrounding environment.
BURR KING MFG. CO., INC. 1220 TAMARA LANE WARSAW, MO 65355 WWW.BURRKING.COM (660) 438-8998 s (800) 621-2748 FAX (660) 438-8991 Technical tip May 16, 2006 As you may know we improved many of our 120 and 220-volt single-phase variable speed grinders and buffers to use a three-phase AC motor with an inverter controller rather than the DC motors and a rectifier controller previously used. This change is transparent to the end user since the machine is “plugged in” to single-phase outlets.
motors. To force these inadequate services to deliver power that is greater than their designed 15-ampere capability leads to early equipment failure and potential fire danger. This must always be considered when choosing the electrical supply. • • • • • • Burr King provides 1-½ horsepower, 120-volt machines with a 20-ampere power cables and connectors.
BURR KING MFG. CO., INC. 1220 TAMARA LANE WARSAW MO 65355 WWW.BURRKING.COM (660) 438-8998 s (800) 621-2748 FAX (660) 438-8991 April 2002 Operating instructions for the Model 960-250 or 960-400 belt grinders The model 960-250 or 960-400 belt grinders are two wheel path belt grinders that use a 2.5 or 4.0 x 60-inch continuous loop abrasive belt. For maximum effectiveness, and operator safety use abrasive belts manufactured by well respected abrasive manufacturers.
. Burr King recommends that all three phase installations include a magnetic starter. Magnetic starters protect motors from “single phasing”, overheating, etc. thereby reducing the risk of damage to the equipment and/or fire hazard to your facility. 11. Insure that the model 960-250 or 960-400 AC power source is properly sized, and properly fused. You should consult a competent electrician, or you may call Burr King Manufacturing for guidance.
Do not operate the model 960-250 or 960-400 with the safety guard open or the contact wheel guard/platen assembly (or internal grinding attachment) removed. Do not reach inside the safety guards while the machine is running. To do so is hazardous. Do not use fluids in your grinding process unless your model 960-250 or 960-400 is designed for liquid operation (NEMA 4, 4X). To do so may create an electrical safety hazard.
67 MODEL 960-250 9 70 7 BURR KING PARTS LIST 945 1220 TAMARA LANE WARSAW, MO.
BURR KING MODEL 960-250 1220 TAMARA LANE WARSAW, MO. 65355 PARTS LIST ITEM # PART # DESCRIPTION ITEM # PART # DESCRIPTION ITEM 53 LIST - 945 ITEM # PART # DESCRIPTION BELT, V DRIVE BEARING, CONTACT WHEEL ASSY 67 68 940 935 725 PULLEY, 2 1/2 69 937G 726 WASHER, SPRING FLANGE 70 736 RACHET 727 NUT, 5/8-18 RH, JAM, BRT PLT 71 939 GUIDE, SPRING 41 42 730 802 PULLEY, 3 CONTACT WHEEL, 7x2.
MAG STARTER BURR KING PARTS LIST 1220 TAMARA LANE WARSAW, MO.
BURR KING 1220 TAMARA LANE WARSAW, MO. 65355 ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 MAG STARTER PART NUMBER DESCRIPTION MB-4C BRACKET, MOUNTING, STARTER MOTOR CALL FACTORY FOR PART NUMBER 4 WASHER, 5/16 SAE ZINC PLTD 37 BOLT, 5/16-18x3/4 HEX HEAD 5 WASHER, 1/4 AN 209 SCREW, 1/4-20 X 3/4 ALLEN HEAD 4-0013 NUT, KEP, 1/4-20 MS2A3 3/4HP-1HP, 220V MS4A3 3/4HP-1HP, 440V MS2B3 1.5HP-3HP, 220V MS4B3 1.5HP-3HP, 440V 775 CONNECTOR, 3/8", STR, LIQ. TIGHT 776 CONNECTOR, 3/8", 90 DEG, LIQ.
VARI SPEED BURR KING SINGLE PHASE 1220 TAMARA LANE WARSAW, MO. 65355 3/4-1 HP 1.
ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 VARI SPEED PART NUMBER MB-4C 941-3 5-0032 4 209 5 4-0013 100B-1725C 150B-1725C 37 015-1 017 020 864-1 775 776 643 862-3 DESCRIPTION BRACKET, MOUNTING, STARTER BRACE, MB4 SUPPORT WASHER, 1/4, LOCK, SPLIT, PLTD WASHER, 5/16 SAE ZINC PLTD SCREW, 1/4-20 X 3/4 ALLEN HEAD WASHER, 1/4 AN NUT, KEP, 1/4-20 1 HP MOTOR 1.5 HP MOTOR BOLT, 5/16-18x3/4 HEX HEAD 120V CORD 220V CORD CONDUIT 3/8" LIQUIDTIGHT CONT. 115/220V 0.75-1HP CONNECTOR, 3/8" STR, LIQ.
BURR KING 8.3 7.25 1220 TAMARA LANE WARSAW, MO. 65355 .312 (4) PLCS 8.8 M960-250 BASIC DIMENSIONS 7.
