Operating Instructions LEVEL SWITCH 8111 with NAMUR output
Contents Contents 1 About this document 1.1 1.2 1.3 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. .. .. .. .. .. .. .. 5 5 5 5 6 6 6 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. .. .. .. 7 8 8 9 General instructions . . . . . . . . . . . . . . . . . . . . . . . . . Instructions for installation . . . . . . . . . . . . . .
Contents Supplementary documentation Information: Supplementary documents appropriate to the ordered version come with the delivery. You can find them listed in chapter "Product description". Instructions manuals for accessories and replacement parts 32048-EN-120418 Tip: To ensure reliable setup and operation of your LEVEL SWITCH 8111, we offer accessories and replacement parts.
1 About this document 1 About this document 1.1 Function This operating instructions manual provides all the information you need for mounting, connection and setup as well as important instructions for maintenance and fault rectification. Please read this information before putting the instrument into operation and keep this manual accessible in the immediate vicinity of the device. 1.2 Target group This operating instructions manual is directed to trained qualified personnel.
2 For your safety 2 For your safety 2.1 Authorised personnel All operations described in this operating instructions manual must be carried out only by trained specialist personnel authorised by the plant operator. During work on and with the device the required personal protective equipment must always be worn. 2.2 Appropriate use The LEVEL SWITCH 8111 is a sensor for level detection. You can find detailed information on the application range in chapter "Product description".
2 For your safety 2.5 Safety label on the instrument The safety approval markings and safety tips on the device must be observed. 2.6 CE conformity This device fulfills the legal requirements of the applicable EC guidelines. By attaching the CE mark, we provide confirmation of successful testing. 2.7 SIL conformity LEVEL SWITCH 8111 fulfills the requirements to functional safety according to IEC 61508 resp. IEC 61511. You find further information in the Safety Manual "LEVEL SWITCH". 2.
3 Product description 3 Product description 3.1 Structure Scope of delivery The scope of delivery encompasses: l l Constituent parts LEVEL SWITCH 8111 point level switch Documentation - this operating instructions manual - Safety Manual "Functional safety according to IEC 61508 resp.
3 Product description 3.2 Principle of operation Application area LEVEL SWITCH 8111 is a point level sensor with tuning fork for level detection. It is designed for industrial use in all areas of process technology and can be used in liquids. Typical applications are overfill and dry run protection. With a tuning fork of only 40 mm length, LEVEL SWITCH 8111 can be also mounted e.g. in pipelines from DN 32. The small tuning fork allows use in vessels, tanks and pipes.
3 Product description l l l Signal lamp for indication of the switching condition (green/red) DIL switch for sensitivity adjustment Mode adjustment for selection of the switching condition (A/B) 3.4 Storage and transport Packaging Your instrument was protected by packaging during transport. Its capacity to handle normal loads during transport is assured by a test according to DIN EN 24180. The packaging of standard instruments consists of environmentfriendly, recyclable cardboard.
4 Mounting 4 Mounting 4.1 General instructions Suitability for the process conditions Make sure that all parts of the instrument exposed to the process, in particular the sensor element, process seal and process fitting, are suitable for the existing process conditions. These include above all the process pressure, process temperature as well as the chemical properties of the medium. You can find the specifications in chapter "Technical data" and on the type label.
4 Mounting 2 1 4 3 Fig. 2: Installation vertical 1 2 3 4 Switching point Switching point Switching point Switching point approx. 13 mm (0.51 in) with lower density with higher density approx. 27 mm (1.06 in) 1 Fig.
4 Mounting 2 1 Fig. 4: Horizontal installation (recommended mounting position, particularly for adhesive products) 1 2 Switching point Marking with screwed version on top, with flange versions directed to the flange holes With flange versions, the fork is directed as follows to the flange holes. Fig. 5: Fork position with flange versions Moisture Use the recommended cables (see chapter "Connecting to power supply") and tighten the cable gland.
4 Mounting Fig. 6: Measures against moisture penetration Transport Caution: Do not hold LEVEL SWITCH 8111 on the tuning fork. Particularly with flange or tube versions, the tuning fork can be damaged just by the weight of the instrument. Transport coated instruments very carefully and avoid touching the tuning fork. Remove the packaging or the protective cover just before installation. Pressure/Vacuum The process fitting must be sealed if there is gauge or low pressure in the vessel.
4 Mounting Keep in mind that this welded socket is not suitable for coated instrument versions. Screw LEVEL SWITCH 8111 completely into the welded socket. The later position can be determined already before welding. Mark the appropriate position of the welded socket. Before welding, unscrew LEVEL SWITCH 8111 and remove the rubber ring from the welded socket. The welded socket has a marking (notch).
4 Mounting Instruments with enamel coating should be treated very carefully and shocks should be avoided. Unpack LEVEL SWITCH 8111 directly before installation. Insert LEVEL SWITCH 8111 carefully into the vessel opening and avoid touching any sharp vessel parts.
5 Connecting to power supply 5 Connecting to power supply 5.1 Preparing the connection Note safety instructions Always keep in mind the following safety instructions: l Take note of the safety instructions for Ex applications Voltage supply Connect only in the complete absence of line voltage In hazardous areas you must take note of the respective regulations, conformity and type approval certificates of the sensors and power supply units.
5 Connecting to power supply 5 Open the terminals with a screwdriver 6 Insert the wire ends into the open terminals according to the wiring plan 7 Tighten the terminals with a screwdriver 8 Check the hold of the wires in the terminals by lightly pulling on them 9 Tighten the compression nut of the cable entry. The seal ring must completely encircle the cable 10 Screw the housing cover back on The electrical connection is finished. 5.
5 Connecting to power supply - + 1 2 - + Fig.
6 Set up 6 Set up 6.1 General information The figures in brackets refer to the following illustrations. Function/Configuration The switching condition of the electronics can be checked with closed housing cover (control lamp). In the basic setting, products with a density > 0.7 g/cm³ (0.025 lbs/in³) can be detected. For products with lower density, the switch must be set to > 0.5 g/cm³ (0.018 lbs/in³).
6 Set up Signal lamp (1) Single-coloured control lamp for indication of the switching condition. l l l Characteristics reversal (2) red = High current ≥ 2.6 mA dark = Low current ≤ 0.6 mA red (flashing) = Failure ≤ 0.6 mA The characteristics reversal can be carried out with the DIL switch. You can choose between falling characteristic curve (switch position max.) and rising characteristic curve (switch position min.). This allows you to output the desired current. Modes l l min.
6 Set up Note: The mode setting on the NAMUR amplifier must be selected in such a way that the switching output takes on safe condition in case of failure (I ≤ 0.6 mA). Level Signal current Sensor Falling characteristics max. ≥ 2.6 mA Falling characteristics max. ≤ 0.6 mA Rising characteristics min. ≥ 2.6 mA Rising characteristics min. ≤ 0.6 mA Malfunction any Control lamp ≤ 0.
7 Maintenance and fault rectification 7 Maintenance and fault rectification 7.1 Maintenance If the instrument is used properly, no special maintenance is required in normal operation. 7.2 Remove interferences Reaction when malfunctions occur The operator of the system is responsible for taking suitable measures to rectify faults. Failure reasons LEVEL SWITCH 8111 offers maximum reliability. Nevertheless, faults can occur during operation. These may be caused by the following, e. g.
7 Maintenance and fault rectification Error Signal lamp flashes red Reaction after fault rectification Cause Rectification Wrong characteristic selected Set the correct characteristics on the characteristics reversal switch (overflow protection, dry run protection). Wiring should be carried out according to the quiescent current principle. Error on the vibrating element Check if the vibrating element is damage or extremely corroded.
8 Dismounting 8 Dismounting 8.1 Dismounting steps Warning: Before dismounting, be aware of dangerous process conditions such as e.g. pressure in the vessel, high temperatures, corrosive or toxic products etc. Take note of chapters "Mounting" and "Connecting to power supply" and carry out the listed steps in reverse order. With Ex instruments, the housing cover may only be opened if there is no explosive atmosphere present. 8.
9 Supplement 9 Supplement 9.1 Technical data General data Material 316L corresponds to 1.4404 or 1.4435 Materials, wetted parts - Process fitting - thread - Process fitting - flange 316L, 316L with Hastelloy C22 coating, steel enamelled, 316L with ECTFE coating, 316L with PFA coating - Process seal Klingersil C-4400 - Tuning fork 316L, Hastelloy C22 (2.
9 Supplement - Thread G¾ A, ¾ NPT 75 Nm (55 lbf ft) - Thread G1 A, 1 NPT 100 Nm (73 lbf ft) High voltage test (enamel) max. 5 KV Gas-tight leadthrough (optional) - Leakage rate < 10-6 mbar l/s - Pressure resistance PN 64 Output variable Output Two-wire NAMUR output Current consumption - Falling characteristics ≥ 2.6 mA uncovered/≤ 0.6 mA covered - rising characteristics ≤ 0.6 mA uncovered/≥ 2.6 mA covered - Fault message ≤ 0.
9 Supplement Influence of the process temperature on the switching point 1 4 10 ( 25/64") 8 ( 5/16") 6 ( 15/64") 4 ( 5/32") 2 ( 5/64") 3 0 2 -2 (-5/64") -4 (-5/32") -6 (-15/64") -8 (-5/16") -10 (-25/64") 50 °C (122 °F) 0 °C (32 °F) 100 °C (212 °F) 150 °C (302 °F) 200 °C (392 °F) 250 °C (482 °F) Fig.
9 Supplement Influence of the process pressure to the switching point 1 4 10 ( 25/64") 8 ( 5/16") 6 ( 15/64") 4 ( 5/32") 3 2 ( 5/64") 0 2 -2 (-5/64") -4 (-5/32") -6 (-15/64") -8 (-5/16") -10 (-25/64") 12 (174,1) 25 (362,6) 38 (551,1) 51 (739,7) 64 (928,2) Fig. 22: Influence of the process pressure to the switching point 1 2 3 4 Shifting of the switching point in mm (in) Process pressure in bar (psig) Switching point at reference conditions (notch) Tuning fork Repeatability 0.1 mm (0.
9 Supplement - LEVEL SWITCH 8111 enamelled -50 … +200 °C (-58 … +392 °F) - LEVEL SWITCH 8111 with ECTFE coating -50 … +150 °C (-58 … +302 °F) - LEVEL SWITCH 8111 with PFA coating -50 … +150 °C (-58 … +302 °F) 2 3 70 °C (158 °F) 40 °C (104 °F) 0 °C (32 °F) -50 °C (-58 °F) 1 50 °C (122 °F) 100 °C (212 °F) 150 °C (302 °F) 200 °C (392 °F) 250 °C (482 °F) -40 °C (-40 °F) Fig.
9 Supplement 1 64 (928) 40 (580) 20 (290) -1 (-14,5) -50 °C (-58 °F) 0 °C (32 °F) 50 °C (122 °F) 100 °C (212 °F) 150 °C (302 °F) 200 °C (392 °F) 250 °C (482 °F) 2 Fig. 25: Process temperature - Process pressure with switch position 0.5 g/cm³ (sensitivity switch) 1 2 Process pressure in bar (psig) Process temperature in °C (°F) Viscosity - dynamic 0.1 … 10,000 mPa s (requirement: with density 1) Flow velocity max. 6 m/s (with a viscosity of 1 mPa s) Density 0.7 … 2.5 g/cm³ (0.025 … 0.
9 Supplement Electrical protective measures 32048-EN-120418 Protection rating - Plastic housing IP 66/IP 67 - Aluminium and stainless steel standard IP 66/IP 68 (0.2 bar)1) - Aluminium and stainless housing (optionally available) IP 66/IP 68 (1 bar) Overvoltage category III Protection class II 1) A suitable cable is the prerequisite for maintaining the protection rating.
9 Supplement 9.2 Dimensions LEVEL SWITCH 8111 M20x1,5/ ½ NPT ø 91 mm (3 37/64") 127 mm (5") ~ 76 mm (2 63/64") Fig.
9 Supplement 1 2 55 mm (2.17") 57 mm (2.24") 36 mm (1.42") 53 mm (2.09") 32 (G¾A, ¾"NPT) 41 (G1A, 1"NPT) G¾A, ¾"NPT G1A, 1"NPT 6 3 5 49 mm (1.93") 53 mm (2.09") 4 50 mm (1.97") ø 33,7 mm (1.33") 53 mm (2.09") 50 mm (1.97") 19 mm (0.75") G¾=66 mm (2.6") G1=69 mm (2.72") 18,5 mm (0.73") LEVEL SWITCH 8111 6 Fig.
9 Supplement 34 mm (1.34") 178 mm (7.01") LEVEL SWITCH 8111, options 1 2 Fig.
32048-EN-120418 9 Supplement LEVEL SWITCH 8111 • with NAMUR output 35
The smart choice of Fluid Control Systems www.burkert.
Bedienungsanleitung LEVEL SWITCH 8111 mit NAMUR-Ausgang
Inhaltsverzeichnis Inhaltsverzeichnis 1 Zu diesem Dokument 1.1 1.2 1.3 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. .. .. .. .. .. .. .. 5 5 5 5 6 6 6 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. .. .. .. 7 8 8 9 Allgemeine Hinweise . . . . . . . . . . . . . . . . . . . . . . . . Montagehinweise . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 14 Aufbau. . . . . . . . . . . . .
Inhaltsverzeichnis Ergänzende Dokumentation Information: Je nach bestellter Ausführung gehört ergänzende Dokumentation zum Lieferumfang. Diese finden Sie im Kapitel "Produktbeschreibung". Anleitungen für Zubehör und Ersatzteile 32048-DE-120412 Tipp: Für den sicheren Einsatz und Betrieb Ihres LEVEL SWITCH 8111 bieten wir Zubehör und Ersatzteile an.
1 Zu diesem Dokument 1 Zu diesem Dokument 1.1 Funktion Die vorliegende Betriebsanleitung liefert Ihnen die erforderlichen Informationen für Montage, Anschluss und Inbetriebnahme sowie wichtige Hinweise für Wartung und Störungsbeseitigung. Lesen Sie diese deshalb vor der Inbetriebnahme und bewahren Sie sie als Produktbestandteil in unmittelbarer Nähe des Gerätes jederzeit zugänglich auf. 1.2 Zielgruppe Diese Betriebsanleitung richtet sich an ausgebildetes Fachpersonal.
2 Zu Ihrer Sicherheit 2 Zu Ihrer Sicherheit 2.1 Autorisiertes Personal Sämtliche in dieser Betriebsanleitung beschriebenen Handhabungen dürfen nur durch ausgebildetes und vom Anlagenbetreiber autorisiertes Fachpersonal durchgeführt werden. Bei Arbeiten am und mit dem Gerät ist immer die erforderliche persönliche Schutzausrüstung zu tragen. 2.2 Bestimmungsgemäße Verwendung Der LEVEL SWITCH 8111 ist ein Sensor zur Grenzstanderfassung.
2 Zu Ihrer Sicherheit 2.5 Sicherheitskennzeichen am Gerät Die auf dem Gerät angebrachten Sicherheitskennzeichen und hinweise sind zu beachten. 2.6 CE-Konformität Dieses Gerät erfüllt die gesetzlichen Anforderungen der zutreffenden EG-Richtlinien. Mit der Anbringung des CE-Zeichens bestätigen wir die erfolgreiche Prüfung. 2.7 SIL-Konformität Der LEVEL SWITCH 8111 erfüllt die Anforderungen an die funktionale Sicherheit nach IEC 61508 bzw. IEC 61511.
3 Produktbeschreibung 3 Produktbeschreibung 3.1 Aufbau Lieferumfang Der Lieferumfang besteht aus: l l Komponenten Grenzstandsensor LEVEL SWITCH 8111 Dokumentation - Dieser Betriebsanleitung - Safety Manual "Funktionale Sicherheit nach IEC 61508 bzw. IEC 61511 (SIL)" - Ex-spezifischen "Sicherheitshinweisen" (bei Ex-Ausführungen) - Ggf. weiteren Bescheinigungen Der LEVEL SWITCH 8111 besteht aus den Komponenten: l l l Gehäusedeckel Gehäuse mit Elektronik Prozessanschluss mit Schwinggabel 1 2 3 Abb.
3 Produktbeschreibung 3.2 Arbeitsweise Anwendungsbereich Der LEVEL SWITCH 8111 ist ein Grenzstandsensor mit Schwinggabel zur Grenzstanderfassung. Er ist konzipiert für industrielle Einsätze in allen Bereichen der Verfahrenstechnik und kann in Flüssigkeiten eingesetzt werden. Typische Anwendungen sind Überlauf- und Trockenlaufschutz. Mit der nur 40 mm langen Schwinggabel kann der LEVEL SWITCH 8111 z. B. auch in Rohrleitungen ab DN 32 montiert werden.
3 Produktbeschreibung Auf dem Elektronikeinsatz finden Sie folgende Anzeige- und Bedienelemente: l l l Kontrollleuchte zur Anzeige des Schaltzustandes (grün/rot) DIL-Schalter zur Empfindlichkeitsumschaltung Betriebsartenumschaltung zur Wahl des Schaltverhaltens (A/B) 3.4 Lagerung und Transport Verpackung Ihr Gerät wurde auf dem Weg zum Einsatzort durch eine Verpackung geschützt. Dabei sind die üblichen Transportbeanspruchungen durch eine Prüfung nach DIN EN 24180 abgesichert.
4 Montieren 4 Montieren 4.1 Allgemeine Hinweise Eignung für die Prozessbedingungen Stellen Sie sicher, dass sämtliche, im Prozess befindlichen Teile des Gerätes, insbesondere Sensorelement, Prozessdichtung und Prozessanschluss für die auftretenden Prozessbedingungen geeignet sind. Dazu zählen insbesondere Prozessdruck, Prozesstemperatur sowie die chemischen Eigenschaften der Medien. Die Angaben dazu finden Sie im Kapitel "Technische Daten" und auf dem Typschild.
4 Montieren 2 1 4 3 Abb. 2: Einbau senkrecht 1 2 3 4 Schaltpunkt ca. Schaltpunkt bei Schaltpunkt bei Schaltpunkt ca. 13 mm (0.51 in) geringerer Dichte höherer Dichte 27 mm (1.06 in) 1 Abb.
4 Montieren 2 1 Abb. 4: Waagerechter Einbau (empfohlene Einbaulage, vor allem für anhaftende Füllgüter) 1 2 Schaltpunkt Markierung bei Gewindeausführung oben, bei Flanschausführungen auf die Flanschbohrungen ausgerichtet Bei Flanschausführungen ist die Gabel folgendermaßen auf die Flanschbohrungen ausgerichtet. Abb.
4 Montieren Abb. 6: Maßnahmen gegen das Eindringen von Feuchtigkeit Transport Vorsicht: Halten Sie den LEVEL SWITCH 8111 nicht an der Schwinggabel. Insbesondere bei Flansch- oder Rohrversionen kann die Schwinggabel durch das Gerätegewicht beschädigt werden. Transportieren Sie beschichtete Geräte mit äußerster Vorsicht und vermeiden Sie Berührungen mit der Schwinggabel. Entfernen Sie die Verpackung bzw. die Schutzkappe erst unmittelbar vor dem Einbau.
4 Montieren 4.2 Montagehinweise Einschweißstutzen Der LEVEL SWITCH 8111 hat einen definierten Gewindeanfang. Das bedeutet, dass sich jeder LEVEL SWITCH 8111 nach dem Einschrauben immer in derselben Gabelstellung befindet. Entfernen Sie deshalb die mitgelieferte Dichtung vom Gewinde des LEVEL SWITCH 8111. Diese Dichtung wird bei Verwendung des Einschweißstutzens mit vorne liegendem O-Ring nicht benötigt. Beachten Sie, dass dieser Einschweißstutzen nicht für beschichtete Gerätevarianten geeignet ist.
4 Montieren Wenn der LEVEL SWITCH 8111 im Befüllstrom eingebaut ist, kann dies zu unerwünschten Fehlmessungen führen. Montieren Sie den LEVEL SWITCH 8111 deshalb an einer Stelle im Behälter, wo keine störenden Einflüsse, wie z. B. von Befüllöffnungen, Rührwerken etc. auftreten können. Strömungen Damit die Schwinggabel des LEVEL SWITCH 8111 bei Füllgutbewegungen möglichst wenig Widerstand bietet, sollten die Flächen der Schwinggabel parallel zur Füllgutbewegung stehen.
5 An die Spannungsversorgung anschließen 5 An die Spannungsversorgung anschließen 5.1 Anschluss vorbereiten Sicherheitshinweise beachten Beachten Sie grundsätzlich folgende Sicherheitshinweise: l Sicherheitshinweise für ExAnwendungen beachten Spannungsversorgung Nur in spannungslosem Zustand anschließen In explosionsgefährdeten Bereichen müssen die entsprechenden Vorschriften, Konformitäts- und Baumusterprüfbescheinigungen der Sensoren und der Versorgungsgeräte beachtet werden.
5 An die Spannungsversorgung anschließen 2 Überwurfmutter der Kabelverschraubung lösen 3 Anschlusskabel ca. 10 cm (4 in) abmanteln, Aderenden ca. 1 cm (0.
5 An die Spannungsversorgung anschließen - + 1 2 - + Abb.
6 In Betrieb nehmen 6 In Betrieb nehmen 6.1 Allgemein Die Zahlenangaben in Klammern beziehen sich auf die nachfolgenden Abbildungen. Funktion/Aufbau Der Schaltzustand der Elektronik kann bei geschlossenem Gehäusedeckel kontrolliert werden (Kontrollleuchte). In der Grundeinstellung können Füllgüter mit Dichte > 0,7 g/cm³ (0.025 lbs/in³) detektiert werden. Bei Füllgütern mit niedrigerer Dichte müssen Sie den Schalter auf > 0,5 g/cm³ (0.018 lbs/in³) stellen.
6 In Betrieb nehmen Kontrollleuchte (1) Einfarbige Kontrollleuchte zur Anzeige des Schaltzustandes. l l l Kennlinienumkehr (2) Rot = High current ≥ 2,6 mA Dunkel = Low current ≤ 0,6 mA Rot (blinkt) = Störung ≤ 0,6 mA Mit dem DIL-Schalter können Sie die Kennlinie umkehren. Sie können zwischen fallender Kennlinie (Schalterstellung max.) und steigender Kennlinie (Schalterstellung min.) wählen. Sie können damit den gewünschten Strom ausgeben lassen. Betriebsarten l l Min.
6 In Betrieb nehmen 6.3 Funktionstabelle Die folgende Tabelle gibt eine Übersicht über die Schaltzustände in Abhängigkeit von der eingestellten Betriebsart und dem Füllstand. Hinweis: Die Betriebsarteinstellung am NAMUR-Trennschaltverstärker ist so zu wählen, dass der Schaltausgang bei Störmeldung (I ≤ 0,6 mA) in die sichere Lage geht. Füllstand Signalstrom - Sen- Kontrollleuchte sor Fallende Kennlinie max. ≥ 2,6 mA Fallende Kennlinie max. ≤ 0,6 mA Steigende Kennlinie min.
7 Instandhalten und Störungen beseitigen 7 Instandhalten und Störungen beseitigen 7.1 Wartung Bei bestimmungsgemäßer Verwendung ist im Normalbetrieb keine besondere Wartung erforderlich. 7.2 Störungen beseitigen Verhalten bei Störungen Es liegt in der Verantwortung des Anlagenbetreibers, geeignete Maßnahmen zur Beseitigung aufgetretener Störungen zu ergreifen. Störungsursachen Der LEVEL SWITCH 8111 bietet Ihnen ein Höchstmaß an Funktionssicherheit.
7 Instandhalten und Störungen beseitigen Fehler Ursache Beseitigung Falsche Kennlinie Korrekte Kennlinie am Kennlinienumgewählt kehrschalter einstellen (Überlaufschutz, Trockenlaufschutz). Die Verkabelung sollte nach dem Ruhestromprinzip ausgeführt werden. Kontrollleuchte blinkt rot Verhalten nach Störungsbeseitigung Fehler am Schwingelement Kontrollieren Sie, ob das Schwingelement beschädigt oder stark korrodiert ist.
8 Ausbauen 8 Ausbauen 8.1 Ausbauschritte Warnung: Achten Sie vor dem Ausbauen auf gefährliche Prozessbedingungen wie z. B. Druck im Behälter, hohe Temperaturen, aggressive oder toxische Füllgüter etc. Beachten Sie die Kapitel "Montage" und "An die Spannungsversorgung anschließen" und führen Sie die dort angegebenen Schritte sinngemäß umgekehrt durch. Bei Ex-Geräten darf der Gehäusedeckel nur dann geöffnet werden, wenn keine explosionsfähige Atmosphäre vorhanden ist. 8.
9 Anhang 9 Anhang 9.1 Technische Daten Allgemeine Daten Werkstoff 316L entspricht 1.4404 oder 1.4435 Werkstoffe, medienberührt - Prozessanschluss - Gewinde - Prozessanschluss - Flansch - Prozessdichtung Klingersil C-4400 - Schwinggabel 316L, Hastelloy C22 (2.
9 Anhang - Gewinde G¾ A, ¾ NPT 75 Nm (55 lbf ft) - Gewinde G1 A, 1 NPT 100 Nm (73 lbf ft) Hochspannungsprüfung (Email) max.
9 Anhang Einfluss der Prozesstemperatur auf den Schaltpunkt 1 4 10 ( 25/64") 8 ( 5/16") 6 ( 15/64") 4 ( 5/32") 2 ( 5/64") 3 0 2 -2 (-5/64") -4 (-5/32") -6 (-15/64") -8 (-5/16") -10 (-25/64") 50 °C (122 °F) 0 °C (32 °F) 100 °C (212 °F) 150 °C (302 °F) 200 °C (392 °F) 250 °C (482 °F) Abb.
9 Anhang Einfluss des Prozessdrucks auf den Schaltpunkt 1 4 10 ( 25/64") 8 ( 5/16") 6 ( 15/64") 4 ( 5/32") 3 2 ( 5/64") 0 2 -2 (-5/64") -4 (-5/32") -6 (-15/64") -8 (-5/16") -10 (-25/64") 12 (174,1) 25 (362,6) 38 (551,1) 51 (739,7) 64 (928,2) Abb. 22: Einfluss des Prozessdrucks auf den Schaltpunkt 1 2 3 4 Verschiebung des Schaltpunktes in mm (in) Prozessdruck in bar (psig) Schaltpunkt bei Referenzbedingungen (Einkerbung) Schwinggabel Wiederholbarkeit 0,1 mm (0.004 in) Hysterese ca. 2 mm (0.
9 Anhang - LEVEL SWITCH 8111 aus 316L/Hastelloy C22 (2.4602) -50 … +250 °C (-58 … +482 °F) - LEVEL SWITCH 8111 emailliert -50 … +200 °C (-58 … +392 °F) - LEVEL SWITCH 8111 mit ECTFE beschichtet -50 … +150 °C (-58 … +302 °F) - LEVEL SWITCH 8111 mit PFA beschichtet -50 … +150 °C (-58 … +302 °F) 2 3 70 °C (158 °F) 40 °C (104 °F) 0 °C (32 °F) -50 °C (-58 °F) 1 50 °C (122 °F) 100 °C (212 °F) 150 °C (302 °F) 200 °C (392 °F) 250 °C (482 °F) -40 °C (-40 °F) Abb.
9 Anhang 1 64 (928) 40 (580) 20 (290) -1 (-14,5) -50 °C (-58 °F) 0 °C (32 °F) 50 °C (122 °F) 100 °C (212 °F) 150 °C (302 °F) 200 °C (392 °F) 250 °C (482 °F) 2 Abb. 25: Prozesstemperatur - Prozessdruck bei Schalterstellung 0,5 g/cm³ (Empfindlichkeitsumschalter) 1 2 Prozessdruck in bar (psig) Prozesstemperatur in °C (°F) Viskosität - dynamisch 0,1 … 10.000 mPa s (Voraussetzung: bei Dichte 1) Fließgeschwindigkeit max. 6 m/s (bei einer Viskosität von 1 mPa s Dichte 0,7 … 2,5 g/cm³ (0.025 … 0.
9 Anhang Elektrische Schutzmaßnahmen 32048-DE-120412 Schutzart - Kunststoffgehäuse IP 66/IP 67 - Aluminium- und Edelstahlgehäuse Standard IP 66/IP 68 (0,2 bar)1) - Aluminium- und Edelstahlgehäuse (optional) IP 66/IP 68 (1 bar) Überspannungskategorie III Schutzklasse II 1) Voraussetzung für die Einhaltung der Schutzart ist das passende Kabel.
9 Anhang 9.2 Maße LEVEL SWITCH 8111 M20x1,5/ ½ NPT ø 91 mm (3 37/64") 127 mm (5") ~ 76 mm (2 63/64") Abb.
9 Anhang 1 2 55 mm (2.17") 57 mm (2.24") 36 mm (1.42") 53 mm (2.09") 32 (G¾A, ¾"NPT) 41 (G1A, 1"NPT) G¾A, ¾"NPT G1A, 1"NPT 6 3 5 49 mm (1.93") 4 50 mm (1.97") ø 33,7 mm (1.33") 53 mm (2.09") 53 mm (2.09") 50 mm (1.97") 19 mm (0.75") G¾=66 mm (2.6") G1=69 mm (2.72") 18,5 mm (0.73") LEVEL SWITCH 8111 6 Abb.
9 Anhang 34 mm (1.34") 178 mm (7.01") LEVEL SWITCH 8111 - Optionen 1 2 Abb.
32048-DE-120412 9 Anhang LEVEL SWITCH 8111 • mit NAMUR-Ausgang 35
The smart choice of Fluid Control Systems www.buerkert.
Mise en service LEVEL SWITCH 8111 avec sortie NAMUR
Table des matières Table des matières 1 À propos de ce document 1.1 1.2 1.3 2 . . . . . . . . . . . . . . . . .. .. .. .. 7 8 9 9 Remarques générales. . . . . . . . . . . . . . . . . . . . . . . . Consignes de montage . . . . . . . . . . . . . . . . . . . . . . . 11 15 Structure . . . . . . . . . . . . . . Procédé de fonctionnement. Réglage . . . . . . . . . . . . . . . Stockage et transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table des matières Documentation complémentaire Information: Suivant la version commandée, une documentation complémentaire fera partie de la livraison. Elle vous sera indiquée au chapitre "Description du produit".
1 À propos de ce document 1 À propos de ce document 1.1 Fonction La présente notice technique contient les informations nécessaires vous permettant un montage, un raccordement et une mise en service de l'appareil ainsi que des remarques importantes concernant l'entretien et l'élimination des défauts. Il est donc important de la lire avant d'effectuer la mise en service et de la conserver près de l'appareil, accessible à tout moment comme partie intégrante du produit. 1.
2 Pour votre sécurité 2 Pour votre sécurité 2.1 Personnel autorisé Toutes les manipulations sur l'appareil indiquées dans cette notice ne doivent être effectuées que par du personnel qualifié, spécialisé et autorisé par l'exploitant de l'installation. Porter toujours l'équipement de protection personnel nécessaire en travaillant avec l'appareil. 2.2 Utilisation appropriée Le LEVEL SWITCH 8111 est un appareil destiné à la détection de niveau.
2 Pour votre sécurité 2.5 Caractéristiques de sécurité sur l'appareil Les caractéristiques et remarques de sécurité se trouvant sur l'appareil sont à respecter. 2.6 Conformité CE Cet appareil satisfait aux exigences légales des directives respectives de la CE. Avec le marquage CE, nous confirmons que le contrôle a été effectué avec succès. 2.7 Conformité SIL Le LEVEL SWITCH 8111 satisfait aux exigences relatives à la sécurité fonctionnelle selon IEC 61508 et IEC 61511.
3 Description du produit 3 Description du produit 3.
3 Description du produit 3.2 Procédé de fonctionnement Domaine d'application Le LEVEL SWITCH 8111 est un détecteur de niveau à lames vibrantes destiné à la détection de niveau. Il est conçu pour les applications industrielles dans tous les secteurs de la technique des procédés et peut être utilisé dans les liquides. Des applications classiques sont la protection antidébordement et contre la marche à vide.
3 Description du produit 3.3 Réglage Vous pouvez contrôler l'état de commutation du détecteur LEVEL SWITCH 8111 le boîtier étant fermé (témoin de contrôle). En réglage de base, vous pouvez détecter des produits dont la densité est > 0,7 g/ cm³ (0.025 lbs/in³) . Vous pouvez adapter l'appareil si votre produit a une densité plus basse.
3 Description du produit l Humidité relative de l'air 20 … 85 % 32048-FR-120524 10 LEVEL SWITCH 8111 • avec sortie NAMUR
4 Montage 4 Montage 4.1 Remarques générales Aptitude aux conditions process Assurez-vous que tous les éléments de l'appareil se trouvant dans le process, en particulier l'élément capteur, le joint et le raccord process, soient appropriés aux conditions du process. Cela concerne en particulier la pression process, la température process ainsi que les propriétés chimiques du ou des produit(s).
4 Montage 2 1 4 3 Fig. 2: Montage vertical 1 2 3 4 Point Point Point Point de de de de commutation env. 13 mm (0.51 in) commutation avec plus faible densité commutation avec plus haute densité commutation env. 27 mm (1.06 in) 1 Fig.
4 Montage 2 1 Fig. 4: Montage horizontal (position de montage recommandée, en particulier pour les produits colmatants) 1 2 Point de commutation Repère pour version filetée en haut - pour les versions à bride, il est orienté vers les perçages de la bride Dans les versions à brides, les lames sont orientées vers les perçages de la bride de la façon suivante. Fig.
4 Montage Fig. 6: Mesures prises contre l'infiltration d'humidité Transport Avertissement ! Ne tenez pas le détecteur LEVEL SWITCH 8111 par les lames vibrantes. En particulier pour les versions à bride ou à tube, vous pourriez endommager les lames par le poids de l'appareil. Transportez les appareils plaqués avec grande précaution et évitez tout contact avec les lames. Enlevez l'emballage ou le capot de protection que juste avant le montage.
4 Montage 4.2 Consignes de montage Raccord à souder Le détecteur LEVEL SWITCH 8111 possède un filet initial défini. Cela signifie qu'après avoir vissé un LEVEL SWITCH 8111, ses lames se retrouvent toujours dans la même position. Pour cela, il est nécessaire d'enlever le joint se trouvant sur le filetage du LEVEL SWITCH 8111. Ce joint n'est pas nécessaire si vous utilisez le raccord à souder avec joint torique placé à l'avant.
4 Montage Flot de produit Si vous installez le LEVEL SWITCH 8111 dans le flot de remplissage, cela peut entraîner des mesures erronées. Pour l'éviter, nous vous recommandons d'installer le LEVEL SWITCH 8111 à un endroit de la cuve où il ne sera pas perturbé par des influences négatives telles que flots de remplissage ou agitateurs par exemple.
5 Raccordement à l'alimentation de tension 5 Raccordement à l'alimentation de tension 5.
5 Raccordement à l'alimentation de tension 3 Enlever la gaine du câble sur 10 cm (4 in) env. et dénuder l'extrémité des conducteurs sur 1 cm (0.4 in) env. 4 Introduire le câble dans le capteur en le passant par le presseétoupe.
5 Raccordement à l'alimentation de tension - + 1 2 - + 32048-FR-120524 Fig.
6 Mise en service 6 Mise en service 6.1 Généralités Les chiffres entre parenthèses se rapportent aux illustrations suivantes. Fonctionnement/présentation Vous pouvez contrôler l'état de commutation de l'électronique, le couvercle du boîtier étant fermé (témoin de contrôle). En réglage de base, vous pouvez détecter des produits dont la densité est > 0,7 g/ cm³ (0.025 lbs/in³. En présence de produits dont la densité est plus basse, vous devez mettre le commutateur sur > 0,5 g/cm³ (0.018 lbs/ in³).
6 Mise en service 6.2 Éléments de réglage 1 2 3 4 5 Fig.
6 Mise en service > 0,5 g/cm³ (0.018 lbs/in³). Les valeurs indiquées pour la position du point de commutation se rapportent à l'eau - densité 1 g/cm³ (0.036 lbs/ in³). Pour les produits ayant une densité différente de celle de l'eau, ce point de commutation se décalera vers le boîtier ou vers l'extrémité des lames en fonction de la densité et du type de montage. Remarque: Tenez compte que la mousse dont la densité est > 0,45 g/cm³ (0.016 lbs/in³) sera détectée par l'appareil.
6 Mise en service Niveau Courant signal capteur Courbe caractéristique croissante min. ≥ 2,6 mA Courbe caractéristique croissante min.
7 Maintenance et élimination des défauts 7 Maintenance et élimination des défauts 7.1 Maintenance À condition d'un maniement approprié, aucun entretien particulier ne sera nécessaire en fonctionnement normal. 7.2 Éliminer des défauts Comportement en cas de défauts C'est à l'exploitant de l'installation qu'il incombe la responsabilité de prendre les mesures appropriées pour éliminer les défauts survenus. Causes du défaut Le LEVEL SWITCH 8111 vous offre une très haute sécurité de fonctionnement.
7 Maintenance et élimination des défauts Erreur Témoin de contrôle clignote rouge Cause Élimination Colmatages sur l'élément vibrant Assurez-vous qu'il n'y a aucun colmatage sur l'élément vibrant et le manchon. Si c'est le cas, éliminez-les. Choix de la mauvaise courbe caractéristique Régler la courbe caractéristique correcte à l'inverseur de courbe (protection antidébordement, protection contre la marche à vide). Le câblage doit être réalisé suivant le principe du courant repos.
8 Démonter 8 Démonter 8.1 Étapes de démontage Attention ! Avant de démonter l'appareil, prenez garde aux conditions de process dangereuses comme par exemple pression dans la cuve, hautes températures, produits agressifs ou toxiques etc. Suivez les indications des chapitres "Montage" et "Raccordement à l'alimentation" et procédez de la même manière mais en sens inverse. Pour les appareils Ex, vous n'êtes autorisé à ouvrir le couvercle du boîtier qu'en absence complète d'atmosphère explosive. 8.
9 Annexe 9 Annexe 9.1 Caractéristiques techniques Caractéristiques générales Matériau 316L correspond à 1.4404 ou à 1.4435 Matériaux, en contact avec le produit - Raccord process - filetage - Raccord process - bride 316L, 316L plaqué Hastelloy C22, acier émaillé, 316L revêtu ECTFE, 316L revêtu PFA - Joint de process Klingersil C-4400 - Lames vibrantes 316L, Hastelloy C22 (2.
9 Annexe - Filetage G1 A, 1 NPT 100 Nm (73 lbf ft) Test à haute tension (émail) max.
9 Annexe Influence de la température process sur le point de commutation 1 4 10 ( 25/64") 8 ( 5/16") 6 ( 15/64") 4 ( 5/32") 2 ( 5/64") 3 0 2 -2 (-5/64") -4 (-5/32") -6 (-15/64") -8 (-5/16") -10 (-25/64") 50 °C (122 °F) 0 °C (32 °F) 100 °C (212 °F) 150 °C (302 °F) 200 °C (392 °F) 250 °C (482 °F) Fig.
9 Annexe Influence de la pression process sur le point de commutation 1 4 10 ( 25/64") 8 ( 5/16") 6 ( 15/64") 4 ( 5/32") 2 ( 5/64") 3 0 2 -2 (-5/64") -4 (-5/32") -6 (-15/64") -8 (-5/16") -10 (-25/64") 12 (174,1) 25 (362,6) 38 (551,1) 51 (739,7) 64 (928,2) Fig.
9 Annexe - LEVEL SWITCH 8111 en 316L/Hastelloy C22 (2.4602) -50 … +250 °C (-58 … +482 °F) - LEVEL SWITCH 8111 émaillé -50 … +200 °C (-58 … +392 °F) - LEVEL SWITCH 8111 revêtu ECTFE -50 … +150 °C (-58 … +302 °F) - LEVEL SWITCH 8111 revêtu PFA -50 … +150 °C (-58 … +302 °F) 2 3 70 °C (158 °F) 40 °C (104 °F) 0 °C (32 °F) -50 °C (-58 °F) 1 50 °C (122 °F) 100 °C (212 °F) 150 °C (302 °F) 200 °C (392 °F) 250 °C (482 °F) -40 °C (-40 °F) Fig.
9 Annexe 1 64 (928) 40 (580) 20 (290) -1 (-14,5) -50 °C (-58 °F) 0 °C (32 °F) 50 °C (122 °F) 100 °C (212 °F) 150 °C (302 °F) 200 °C (392 °F) 250 °C (482 °F) 2 Fig. 23: Température process - pression process avec position du commutateur 0,5 g/cm³ (commutateur d'inversion de la sensibilité) 1 2 Pression process en bar (psig) Température process en °C (°F) Viscosité - dynamique 0,1 … 10.000 mPa s (condition : avec une densité de 1) Vitesse d'écoulement max.
9 Annexe IU env.
9 Annexe 9.2 Encombrement LEVEL SWITCH 8111 M20x1,5/ ½ NPT ø 91 mm (3 37/64") 127 mm (5") ~ 76 mm (2 63/64") Fig.
9 Annexe 1 2 55 mm (2.17") 57 mm (2.24") 36 mm (1.42") 53 mm (2.09") 32 (G¾A, ¾"NPT) 41 (G1A, 1"NPT) G¾A, ¾"NPT G1A, 1"NPT 6 3 5 49 mm (1.93") 4 50 mm (1.97") ø 33,7 mm (1.33") 53 mm (2.09") 53 mm (2.09") 50 mm (1.97") 19 mm (0.75") G¾=66 mm (2.6") G1=69 mm (2.72") 18,5 mm (0.73") LEVEL SWITCH 8111 6 Fig.
9 Annexe 34 mm (1.34") 178 mm (7.01") LEVEL SWITCH 8111 - Options 1 2 Fig.
32048-FR-120524 9 Annexe LEVEL SWITCH 8111 • avec sortie NAMUR 37
9 Annexe 32048-FR-120524 38 LEVEL SWITCH 8111 • avec sortie NAMUR
32048-FR-120524 9 Annexe LEVEL SWITCH 8111 • avec sortie NAMUR 39
The smart choice of Fluid Control Systems www.burkert.