Product Manual

ManualsBrandsBuilding 36 Technologies ManualsElectronicsDisplay

Product Manual

• Smart Thermostat HD Overview

o Smart Thermostat HD Hardware

 Display

 Thermostat

• Button

• Status LED

• Installation Precautions

o Before installing the Smart Thermostat HD or servicing the HVAC equipment, turn off power

to the system.

o Leave power off until you have finished installing or servicing the HVAC equipment.

o Shorting the electric terminals at the control on the heating or cooling system is not

recommended. Do not test the system this way.

o When testing the existing system or the new Smart Thermostat HD do not run the cooling

system when it is cold outside as this may harm the compressor. Please wait for mild

temperature to test the cooling system.

o You must follow all local codes and ordinances for wiring the system.

o This Smart Thermostat HD should only be powered by a listed Class 2 power supply at 24

VAC (C-Wire or wall transformer).

o An amperage higher than 1 amp to each thermostat terminal may cause damage to the

thermostat.

o Verify that the system is 24 VAC. If the old system is labeled as 120 or 240 volts or has wire

nuts, the system is high voltage. Do NOT install this thermostat on a high voltage system.

Contact a local HVAC professional for help.

o Questions?

 Visit: www.alarm.com/supportcenter or contact your service provider.

• Smart Thermostat HD Installation - Considerations

o This Smart Thermostat HD requires 24 VAC power, it does not have the option to be battery

powered. This is supplied via a common wire, typically identified as C.

o The Smart Thermostat HD can adapt for situations where there are not enough wires in the

bundle at the install location. For example, if you do not have C-Wire but do have 24 VAC

available at the HVAC unit, or if you have upgraded your HVAC equipment and now require

more control wires. For these scenarios, the Smart Thermostat HD may be installed in a way

that requires only 2 wires at the wall. For instructions on this install configuration and

further information, please find the Installation Guide in the separate Power Plate box.

• In the Box / Recommended Tools

o Smart Thermostat HD - Thermostat

o Smart Thermostat HD - Display

o Trim Plate

o Wall Screws x2

o Drywall Anchors x2

o Phillips Screwdriver

o Camera

o Pencil

o Needle nose pliers

Summary of content (9 pages)

PAGE 1
Product Manual • • • • Smart Thermostat HD Overview o Smart Thermostat HD Hardware  Display  Thermostat • Button • Status LED Installation Precautions o Before installing the Smart Thermostat HD or servicing the HVAC equipment, turn off power to the system. o Leave power off until you have finished installing or servicing the HVAC equipment. o Shorting the electric terminals at the control on the heating or cooling system is not recommended. Do not test the system this way.
PAGE 2
• • o Power drill – 3/16th inch (#13) drill bit Smart Thermostat HD Installation – Location o If replacing an old thermostat, the new Smart Thermostat HD can be mounted in its place. If a new location is desired it will be necessary to move the wiring. o New installation and relocation should follow the accompanying guidelines to ensure the most accurate temperature reading and ease of use.  Mount on an inside wall, approximately 5 ft (1.5m) above the floor in a frequently used room.
PAGE 3
Once all wires are identified and a picture is taken, disconnect all of the wires and remove the existing thermostat. Remember to secure the wires so they do not fall into the wall. o Prep wires if needed  Follow these guidelines for safe and secure wire connections: • Ensure the wires are a proper gauge between 16-24 AWG (1.5 – 0.5 mm2) • Make sure wires have exposed straight ends of the appropriate length.  !CAUTION: Verify that the system is 24 VAC.
PAGE 4
• • • • • Smart Thermostat HD Installation – Display Install o Connect the Display to the Thermostat o Once attached the Display will turn on  If the Display does not power on after 30 seconds, verify 24 VAC power is appropriately supplied to the Thermostat from the HVAC system. Smart Thermostat HD Installation - Setup o Follow the onscreen setup wizard to setup the Smart Thermostat HD and connect it to a zwave network.
PAGE 5
• How do I include the Smart Thermostat HD in a Z-Wave network or exclude it from a ZWave network? • • How do I reconfigure my Smart Thermostat HD? • • My wiring has changed and I need to reconfigure the thermostat. I made a mistake during the setup process and want to start again • • Can I setup local schedules? The thermostat is setup prior to installation on a smart home network and schedules are needed.
PAGE 6
• How do I reset my Smart Thermostat HD to the factory settings? I am moving or re-setting up my smart home network and need the Smart Thermostat HD reset to it’s factory settings. • • • necessary. The setup for these schedules can be found here: o INSERT STEPS We suggest making use of your smart home supplied schedules as local scheduling is only available when not connected to your smart home The Smart Thermostat HD can be reset back to its factory settings.
PAGE 7
• The Display is not working. • • The Display may not be configured to wake up when you approach. The Display may not be receiving power. • • • Note: The Hub or Panel may be unaware that this procedure was performed, so it is recommended that you remove the Smart Thermostat HD from the Z-Wave network before performing this reset.
PAGE 8
physically removed from the Thermostat your HVAC control will not behave as expected. Please contact your HVAC professional to remedy the situation as soon as possible. • Notices FCC This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause Harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device.
PAGE 9
brouillage, et (2) l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement. Radiofrequency radiation exposure information: This equipment complies with radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and the body of any persons, user or bystander in a normal operation mode.