AirStation WZR-900DHP User Manual www.buffalotech.com 3501xxxx ver.
Contents Chapter 1 - Product Overview...........................................2 Package Contents..................................................................................2 Diagrams and Layout............................................................................2 Front Panel.......................................................................................................2 Back Panel........................................................................................................
Chapter 1 - Product Overview Package Contents The following items are included in your AirStation package. If any of the items are missing, please contact your vender. AirStation.................................................1 AirStation Setup Card..........................1 AC adapter...............................................1 Stands........................................................1 Ethernet Cable........................................1 USB 3.0 Cable..........................................
1 2 AOSS button To initiate AOSS, hold down this button until the wireless LED flashes (about 1 second). Then, push or click the AOSS button on your wireless client device to complete the connection. Both devices must be powered on for this to work. Power / Diag LED (Green or Red) On (Green): Power is on. Blinking (Green): Booting. Off: Power is off. 2 blinks (Red)**: Flash ROM error. 3 blinks (Red)**: Wired Ethernet LAN error. 4 blinks (Red)**: Wireless LAN error.
Back Panel 1 2 3 4 Mode button This button switches between router mode and bridge mode. Setup card slot This is the slot where the AirStation setup card is stored. The initial settings for the username, password, SSID, and encryption type are provided on the card for logging into Settings. USB Eject button To dismount a USB hard drive, hold down this button about 3 seconds. The USB drive can then be unplugged safely. USB LED (Green) On: A USB drive is connected.
Notes: • WZR-900DHP has an USB 3.0 port and WZR-600DHP2 has an USB 2.0 port. • USB 3.0 hubs are not supported. Use USB 2.0 hubs only. 6 7 8 9 LAN LED (Green) On: An Ethernet device is connected. Blinking: An Ethernet device is communicating. LAN Port Connect your computer, hub, or other Ethernet devices to these ports. This switching hub supports 10 Mbps, 100 Mbps, and 1000 Mbps connections. Internet LED (Green) On: The Internet port is connected. Blinking: The Internet port is transmitting data.
Installation Vertical Placement Attach the stand as shown in the figure below.
Chapter 2 - Installation Initial Setup To configure your AirStation, follow the procedure below. 1 Verify that you can connect to the internet without the AirStation, then turn off your modem and computer. 2 Unplug the LAN cable which connects your computer and modem. 3 Plug one end of the LAN cable into your modem and the other end to the AirStation’s Internet (WAN) port. Turn on the modem.
4 Turn on the AirStation, then wait one minute. Note: If the power does not turn on even when the AC adapter is connected, press the power button on the rear of the AirStation. 5 6 If using a wired LAN, connect the AirStation LAN port and computer using a LAN cable. If using a wireless LAN, connect the computer to the wireless LAN by referring to Chapter 4. Once your computer has booted, the AirStation’s LEDs should be lit as described below: Power/Diag: Green LED on. Wireless: Green LED on.
Note: If the router LED is not lit, hold down the router button for about 3 seconds to switch to router mode. 7 Launch a web browser. If the home screen is displayed, setup is complete. If username and password fields are displayed, enter “admin” for the username and “password” for the password, then click [OK]. Step through the wizard to complete setup. You’ve completed the initial setup of your AirStation. Refer to Chapter 3 for advanced settings.
Appendix A - Supplemental Information Technical Specifications Wireless LAN Interface Standard Compliance Transmission Method Frequency Range Transmission Rate Access Mode Security Wired LAN Interface Standard Compliance Transmission Rate Transmission Encoding Access Method Speed and Flow Control Number of LAN Ports USB Interface Interface Connector Type IEEE 802.11n / IEEE 802.11a / IEEE 802.11g / IEEE 802.
Other Power Supply Power Consumption Dimensions Weight Operating Environment 802.11a Frequency Range USA Canada Mexico Brazil EU Russia Middle East India Australia Hong Kong Philippines Thailand Vietnam Singapore Malaysia South Korea China Taiwan 802.11g Frequency Range USA Canada Mexico Brazil EU Russia Middle East India Australia Hong Kong Philippines Thailand Vietnam Singapore Malaysia South Korea China Taiwan External AC 100-240 V Universal, 50/60 Hz About 23 W (Max) 196 x 185 x 28 mm (7.72 x 7.28 x 1.
Environmental Information • The equipment that you have purchased has required the extraction and use of natural resources for its production. • The equipment may contain hazardous substances that could impact health and the environment. • In order to avoid the dissemination of those substances in our environment and to diminish the pressure on the natural resources, we encourage you to use the appropriate take-back systems.
