User Manual AirStation WHR-600D AirStation WHR-300HP2 www.buffalotech.
Contents Chapter 1 - Product Overview.......................................... 5 Package Contents.................................................................... 5 Hardware Overview.................................................................. 6 Front Panel LEDs............................................................................ 6 Back Panel...................................................................................... 8 Bottom.........................................................
-2-
-3-
-4-
Chapter 1 - Product Overview Package Contents The following items are included in your AirStation package. If any of the items are missing, please contact your vender. • • • • • • AirStation........................................................................................................................................ 1 AirStation Setup Card................................................................................................................. 1 AC adapter...................................
Chapter 1 Product Overview Hardware Overview Front Panel LEDs 1 2 3 4 5 1 AOSS button 2 Power/Diag LED (Green or Red) To initiate AOSS, hold down this button until the wireless LED flashes (about 1 second). Then, push or click the AOSS button on your wireless client device to complete the connection. Both devices must be powered on for this to work. On (Green): Power is on. Off : Power is off. On (Green)*1: Booting. 2 blinks (Red)*2: Flash ROM error.
Chapter 1 Product Overview Continuously blinking*1: Updating firmware, saving settings, or initializing settings. *1 Never unplug the AC adapter while the Buffalo LED is blinking continuously. *2 Turn off AirStation first, wait for a few seconds, then turn it back on. *3 Because the network addresses of both the Internet port (WAN port) and the LAN port are the same, it is not possible to establish communication. Change the LAN-side IP address of the AirStation.
Chapter 1 Product Overview Back Panel 6 7 8 9 10 6 Router Switch On: Router functionality is enabled (router mode). Off : Router functionality is disabled (bridge/AP mode). Auto: This switches between modes automatically based on whether or not another router is detected on the Internet port. The default setting for this switch is Auto. 7 LAN Port Connect your computer, hub, or other Ethernet devices to these ports. This switching hub supports 10 Mbps and 100 Mbps connections.
Chapter 1 Product Overview Bottom Label 11 11 Setup card slot This is the slot where the AirStation setup card is stored. The initial settings for the username, password, SSID, and encryption type are provided on the card for logging into Settings.
Chapter 2 - Installation Initial Setup To configure your AirStation, follow the procedure below. 1 Verify that you can connect to the internet without the AirStation, then turn off your modem and computer. 2 Unplug the LAN cable which connects your computer and modem. disconnect modem 3 computer Plug one end of the LAN cable into your modem and the other end to the AirStation’s Internet (WAN) port. Turn on the modem.
Chapter 2 Installation 4 Turn on the AirStation, then wait one minute. AirStation Connect the power supply power outlet 5 If using a wired LAN, connect the AirStation LAN port and computer using a LAN cable. If using a wireless LAN, connect the computer to the wireless LAN. AirStation 2) connect 1) connect LAN cable 6 computer Once your computer has booted, the AirStation’s LEDs should be lit as described below: Power Wireless Internet access Router On. On. On. On.
Chapter 2 Installation 7 Launch a web browser. If the home screen is displayed, setup is complete. If username and password fields are displayed, enter “admin” for the username and “password” for the password, then click [OK]. Step through the wizard to complete setup. You’ve completed the initial setup of your AirStation.
Appendix A - Specifications WHR-600D Wired LAN Interface Standard Compliance IEEE802.3u (100BASE-TX), IEEE802.3 (10BASE-T) Transmission Rate 10 / 100 Mbps Transmission Encoding 100BASE-TX 4B5B/MLT-3, 10BASE-T Manchester Coding Access Method CSMA/CD Speed and Flow Control 10 / 100 Mbps, Auto Sensing, Auto MDIX Number of LAN Ports 4 LAN Port Connector RJ-45 Wireless LAN Interface Standard Compliance IEEE802.
Appendix A Specifications Other Power Supply External AC 100-240 V Universal, 50/60 Hz Power Consumption About 20 W (Max) Dimensions TBD Weight TBD Operating Environment 0 - 40° C (32 - 104° F), 10 - 85% (non-condensing) 802.11a Frequency Range USA Canada Mexico 5180-5240 MHz (Channels 36, 40, 44, 48) 5745-5825 MHz (Channels 149, 153, 157, 161, 165) EU Russia 5180-5240 MHz (Channels 36, 40, 44, 48) 802.
Appendix A Specifications WHR-300HP2 Wired LAN Interface Standard Compliance IEEE802.3u (100BASE-TX), IEEE802.3 (10BASE-T) Transmission Rate 10 / 100 Mbps Transmission Encoding 100BASE-TX 4B5B/MLT-3, 10BASE-T Manchester Coding Access Method CSMA/CD Speed and Flow Control 10 / 100 Mbps, Auto Sensing, Auto MDIX Number of LAN Ports 4 LAN Port Connector RJ-45 Wireless LAN Interface Standard Compliance IEEE802.
Appendix A Specifications Other Power Supply External AC 100-240 V Universal, 50/60 Hz Power Consumption About 20 W (Max) Dimensions TBD Weight TBD Operating Environment 0 - 40° C (32 - 104° F), 10 - 85% (non-condensing) 802.
Appendix B - Environmental Information • The equipment that you have purchased has required the extraction and use of natural resources for its production. • The equipment may contain hazardous substances that could impact health and the environment. • In order to avoid the dissemination of those substances in our environment and to diminish the pressure on the natural resources, we encourage you to use the appropriate take-back systems.
Appendix C - GPL Information The source code for Buffalo products that use GPL code is available at http://opensource.buffalo.jp/ .
