User's Manual

ManualsBrandsBuddi ManualsElectronicsSmart Tag 4

User Manual

Smart Tag

Installation Manual

Version:

1.2

Date:

07-04-141

Page: 1 of 11

Talbot House, 17 Church Street, Rickmansworth, Hertfordshire WD3 1DE.

Smart Tag 4 Installation Manual

Date: 08-04-21

Version: 1.2

Owned by: Brad Buike Head of Product Engineering

Prepared by: Brad Buike Head of Product Engineering

Checked by: Carlos Grangeia Business Development Director

Approved by: Charles Lewinton Production Test Engineer

The material contained in this document may not be copied, published, transmitted, reproduced or

disclosed, in whole or in part without the prior written permission of buddi Ltd.

Summary of content (11 pages)

PAGE 1
User Manual-Smart Tag 4 Installation Manual Version: 1.2 Date: Page: 07-04-141 1 of 11 Smart Tag 4 Installation Manual Date: 08-04-21 Version: 1.
PAGE 2
User Manual-Smart Tag 4 Installation Manual Version: 1.2 Date: Page: 07-04-141 2 of 11 DOCUMENT HISTORY Version Date Author Description 1.0 07-04-20 B Buike First Release 1.1 22-03-21 B Buike Up-date SAR value in Section 8. 1.2 08-04-21 B Buike Up-date SAR value in Section 8. REFERENCED DOCUMENTS Ref. Document Name Version © buddi Ltd 2021 Talbot House, 17 Church Street, Rickmansworth, Hertfordshire WD3 1DE.
PAGE 3
User Manual-Smart Tag 4 Installation Manual Version: 1.2 Date: Page: 07-04-141 3 of 11 CONTENTS 1. 2. 3. 4. 5. 6. 7. Introduction........................................................................................................... 4 Equipment Description.......................................................................................... 4 Smart Tag Fitting ................................................................................................... 5 Smart Tag Operation .............
PAGE 4
User Manual-Smart Tag 4 Installation Manual Version: 1.2 Date: Page: 07-04-141 4 of 11 1. Introduction This document is intended to be the source reference material for using the Smart Tag V4 product, with the exception of electronic configuration (including set-up and interaction with the on-line monitoring portal). The emphasis here is upon describing the physical features, charging, correct fitting and removal etc. 2. Equipment Description A.
PAGE 5
User Manual-Smart Tag 4 Installation Manual Version: 1.2 Date: Page: 07-04-141 5 of 11 3. Smart Tag Fitting The Smart Tag should be prepared for fitting to the subject by clipping two new Locking Plates in position as shown below in red for clarity. The Locking Pates will be secured in position when the Strap is inserted into the Smart Tag, they protect the strap from being released without physical damage being created for evidence gathering purposes.
PAGE 6
User Manual-Smart Tag 4 Installation Manual Version: 1.2 Date: Page: 07-04-141 6 of 11 4. Smart Tag Operation The Smart Tag communicates to a server-based monitoring platform, which interprets the data provided to populate a web portal user interface. The data sets include the following:           Event Time. GPS Location (Intervals can be defined, or a real-time request made). Geofence Data (Virtual zones for inclusion or exclusion set by map data). Position Type (GPS, RF Beacon).
PAGE 7
User Manual-Smart Tag 4 Installation Manual Version: 1.2 Date: Page: 07-04-141 7 of 11 6. On Body Charger (OBC) The OBC battery will require recharging at intervals consistent with the operating mode being used. It is intended that the OBC is connected to an OBC Dock when not in use, to charge up the device in preparation for connection to the Smart Tag, to fully charge the OBC it should be connected for at least 4 hours. The OBC is attached to the Smart Tag by clicking it over the unit.
PAGE 8
User Manual-Smart Tag 4 Installation Manual Version: 1.2 Date: Page: 07-04-141 8 of 11 7. Sanitization and Re-Use 7.1. Smart Tag 7.1.1. Collection The Smart Tag will be removed as per the removal process above.  Place the Smart Tag and strap into a clean plastic bag and return them to the vehicle for inspection and cleaning. 7.1.2. Inspection The Smart Tag should be inspected for signs of damage, units with damage should be dealt with in accordance with local protocols.
PAGE 9
User Manual-Smart Tag 4 Installation Manual Version: 1.2 Date: Page: 07-04-141 9 of 11 7.2. Smart Tag Strap 7.2.1. Collection When handling the Strap protective gloves should be worn. The strap will be freed from the Smart Tag as part of the Smart Tag Removal process above. 7.2.2. Inspection The Strap should be inspected for signs of damage, straps with damage should be dealt with in accordance with local protocols.
PAGE 10
User Manual-Smart Tag 4 Installation Manual Version: 1.2 Date: Page: 07-04-141 10 of 11 7.3. OBC 7.3.1. Collection When collecting an OBC from a subject protective glove should be worn.  Note any obvious sign of damage.  Return the OBC to the vehicle for inspection and cleaning. 7.3.2. Inspection The OBC should be inspected for signs of damage, units with damage should be dealt with in accordance with local protocols.
PAGE 11
User Manual-Smart Tag 4 Installation Manual Version: 1.2 Date: Page: 07-04-141 11 of 11 8. FCC warning statement    This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.