User's Manual

ManualsBrandsBudderfly ManualsElectronicsDual Band Switch



PartNoS0711011

Description:

InstallingaBudderflyadaptertransformsyourbuilding’sexistingwiringintothe“BudderflyOpenNetwork”andallowstheadapterto

monitorenergyconsumptionandcommunicatethedatatoafacilitycontroller.

Budderflyadaptorswillusetheexistingpowerlineforcommunicationandthusrequirenore‐wiring.

UsingourBudderflysoftware,you

canvisualizeconsumptiondataandmanageeachindividualadapter.

TheBudderflylightingswitchisacomponentoftheBudderflysysteman ddesigned toworkwithallotherBudderflydevices.Itisa

plug‐and‐playreplacementforyourexistinglightingswitch.Onceinstalled,theBudderflyswitchesalsoactasrepeaters

toextendthe

rangeofthenetworkandincreaseefficiency.



Thisdeviceisdesignedforuseonlywithpermanentlyinstalledfixtures.



Installation:

TheBudderflyswitchmaybeusedinnewinstallationsortoreplaceanexistingwallswitch.Itisintendedtobeusedonlyasa2‐wayswitch.Thewiring schematicwillbeasperbelow:



1. Atthe circuit breakerorfuse panel, disconnect the powerfor all of the circuits in

theswitchjunctionbox..

2. DoubleCheckthatthepowerisOFFtotheswitchboxbeforecontinuingbytrying

toturnonthecontrolledload.

3. Removethewallplatefromtheswitchyou

arereplacing.Then,unscrewtheswitch

itselfandpullitoutfromthejunctionbox.

4. Disconnectthewiresfromtheswitchyouarereplacing.

5. FollowtheWiringinformationprovidedbelowtoconnectthewiresasfollows:

o ConnecttheGROUNDwire(usuallyBareCopperorGreen)tothe

Groundwireof

BudderflySwitch(Yellow&Green).

o ConnecttheLOADwire(usuallyBlack)thatgoestothelighttotheLOADwireof

BudderflySwitch(Red).

o ConnecttheLINEwire(usuallyBlack)thatcomesfromtheelectricalservicepanel

totheHOTwireofBudderflySwitch(Black).

ConnecttheNEUTRALwire(usuallyWhite)totheNeutralwireofBudderfly

Switch(White).

6. After you have connected all of the wires, ensure that all of the wire connectors

are firmly attached and that there is no exposed copper except for the GROUND

wire.

7. GentlyplaceBudderflyswitchinto

thejunctionbox,orientingtheunitwiththeLED

barontheleft.Then,screwtheswitchintoplace.

8. Reinstallthewallplate

9. Enablepowertotheswitchfromthecircuitbreakerorfusepanel

10. AfterthePowerLEDcomeson,testthat theswitchisworking properly

by turning

thelightonandoff

11. AddthedeviceaddresstotheBudderflywebapplication.

WARNING–ELECTRICALSHOCKHAZARD

• TheBudderflyDualBandLightSwitchisintendedforinstallationinaccordancewiththeNationalElectric

CodeandlocalregulationsintheUnitedStates.

• Ifyouarenotknowledgeableorcomforta blewithelectricalcircuitry,youshouldhaveaqualifiedelectrician

installtheBudderflyDualBandLightSwitchforyou.



Warning

RISKOFFIRE/ELECTRICALSHOCK/BURNS

ExerciseextremecautionwhenusingBudderflyswitchingdevicestocontrolappliances.

ToavoidtheriskofFire,ElectricalShock,Burnsorotherhazardswerecommendthefollowing:

• InstalltheBudderflyswitchesindooronly.

• NeverusetheBudderlyswitchestocontrolmedical

and/orlifesupportequipment.

• DonotusetheBudderflyswitchestocontrolelectricheatersoranyotherapplianceswhichmaypresenta

hazardousconditionduetounattendedorunintentionalpoweroncontrol.

Never use the Budderfly switches with loads that exceed the maximum rating specified.

WARNING–ELECTRICALSHOCKHAZARD

• TurnOFFthepowertothebranchcircuitfortheswitchandlightingfixtureat

theservicepanel.

• AllwiringconnectionsmustbemadewiththePOWEROFFtoavoidpersonal

injuryand/ordamagetotheswitch.

WiringInformation

• Important:BudderflySwitchisratedforandintendedtoonlybeusedwith

copperwire.

• Use12AWGorlargerwiressuitablefor80



• Remove3/4"(1.9cm)ofinsulationfromeachwire.

• Connectasfollows:Twiststrandsofeachendtightlytogether.Holdbare

endsofwirestogetherandpushfirmlyintowireNut.ScrewNutclockwise

makingsurethatnobareconductorshowsbelowtheconnector.



WARNING: If you are not sure

about any part of the above

instructions, consult a qualified

electrician.

Summary of content (3 pages)

PAGE 1
Description: Installing a Budderfly adapter transforms your building’s existing wiring into the “Budderfly Open Network” and allows the adapter to monitor energy consumption and communicate the data to a facility controller. Budderfly adaptors will use the existing power line for communication and thus require no re‐wiring. Using our Budderfly software, you can visualize consumption data and manage each individual adapter.
PAGE 2
Features: “Power Cut‐Off” mode: ‐ Remote On/Off control ‐ Manual On/Off control ‐ Ability to create a group of devices ‐ Ability to monitor power consumption ‐ LED indicators to show the state of the switch On/Off Control: ‐ Remote Control: o The Budderfly switches can be controlled remotely thru the Budderfly software. o The Budderfly software will inform you that the action was successful.
PAGE 3
WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment FCC Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation.