User's Manual

ManualsBrandsBudderfly ManualsElectronicsPower Pack



POWERPACK

PartNoC0021031

ProvidesLowVoltagePowerAndLineVoltageControlForThirdPartyOccupancySensors



Description

InstallingaBudderflyadaptertransformsyourbuilding’sexistingwiringintothe“BudderflyOpenNetwork”andallowstheadapter

tomonitorenergyconsumptionandcommunicatethedatatoafacilitycontroller.

Budderflyadaptorswillusetheexistingpowerlineforcommunicationandthusrequirenore‐wiring.

UsingourBudderflysoftware,youcanvisualizeconsumptiondataandmanageeachindividualadapter.



TheBudderflyPowerPackisacomponentoftheBudderflysystemanddesignedtoworkwithallotherBudderflydevices.Itisa

plug‐and‐playreplacementforyourexistingPowerPack.Onceinstalled,theBudderflydevicesalsoactasrepeaterstoextendthe

rangeofthenetworkandincreaseefficiency.



TheBudderflyPowerPackisintendedtoprovidepowersupplyforthirdpartyoccupancysensorsthroughits isolated 12VDCand

24VDCoutputs.Itwillalsodetectinputsignalsfromtheoccupancysensorsintherangeof(10VDC~30VDC)andwilldriveloadsup

to20Aon277VAC.



Wheneveroccupancyisdetected,theoccupancysensorssignaltheBudderfly PowerPacktoturnON the lighting loads;after15

secondsofno‐occupancydetectedstatetheBudderflyPowerPackautomaticallyturnsOFFthelightingloads.



WARNING

–

ELECTRICALSHOCKHAZARD

• TheBudderflyPowerPackisintendedforinstallationinaccordancewith

theNationalElectricCodeandlocalregulationsintheUnitedStates.

• Ifyouarenotknowledgeableorcomfortablewithelectricalcircuitry,you

shouldhaveaqualifiedelectriciantoinstalltheBudderflyPowerPackfor

you.



Summary of content (6 pages)

PAGE 1
POWER PACK Part No C0021031 Provides Low Voltage Power And Line Voltage Control For Third Party Occupancy Sensors Description Installing a Budderfly adapter transforms your building’s existing wiring into the “Budderfly Open Network” and allows the adapter to monitor energy consumption and communicate the data to a facility controller. Budderfly adaptors will use the existing power line for communication and thus require no re‐wiring.
PAGE 2
Warning RISK OF FIRE RISK OF ELECTRICAL SHOCK RISK OF BURNS Exercise extreme caution when using Budderfly devices to control appliances. To avoid the risk of Fire, Electrical Shock, Burns or other hazards we recommend the following: • Install the Budderfly devices indoor only. • Never use the Budderfly devices to control medical and/or life support equipment.
PAGE 3
1. 2. At the circuit breaker or fuse panel, disconnect the power for all of the circuits in the device junction box. Double Check that the power is OFF to the device box before continuing by trying to turn on the controlled load using the wall switch. 3. Unscrew the cover of the junction box where the Budderfly Power Pack will be installed, and remove the existing power pack (in case you are replacing an existing Power Pack). 4.
PAGE 4
Features ‐ ‐ ‐ ‐ ‐ ‐ ‐ Isolated Internal voltage regulators – Regulated 12VDC and 24VDC sources;1.44W total output Fast installation – Mounts to a knockout hole with a twist‐on nut inside or outside a junction box or a ballast cavity Size (1/2 inch chase nipple not included): 1.7” X 2.29” X 3.
PAGE 5
Reset: If the device stops responding, it can be restarted by pushing the Reset Button. A non‐metallic pin should be used to push the reset button. None of the stored parameters are affected. WARNING –ELECTRICAL SHOCK HAZARD • • Use only the plastic (non‐metallic) pin provided with the device to press the reset button. Never use a metallic pin to press the reset button. Communication: The Budderfly devices use the power line to communicate with the “Facility Controller”.
PAGE 6
Specifications: Power: 120V ‐ 277V AC/ 60Hz Maximum Relay Load Ratings: • 120VAC: o 20A Standard Ballast o 16A Electronic Ballast o 20FLA, 120LRA Motor Load • 240VAC: o 17FLA, 102LRA Motor Load o 5000 W Tungsten • 277VAC: o 20A Standard Ballast o 16A Electronic Ballast o 14FLA, 84LRA Motor Load o o Operating Temperature: 0 C to +40 C Certification: UL certification is in progress For indoor use only Specifications subject to change without notice due to continuing product improvement.