User's Manual

ManualsBrandsBTI Wireless ManualsElectronicsMulti-Carrier Power Amplifier

LPA2100-160-SW01

BRAVO TECH INC

Add.: 6185 Phyllis Drive Unit D, Cypress, CA 90630

Phone: 1-714-230-8333 Website: www.bravotechinc.com

Revision: SP·LPA2100-160-SW01·REV.A

Page: 1

LPA2100-160-SW01 SPECIFICATION

1. System advantages

Bravo Tech Inc 's newly introduced Multi-Carrier High Power Outdoor Booster platform provides high

er downlink EIRP and improved uplink sensitivity at the same time to extend the coverage of existing cellu

lar networks. This multi-carrier based product platform can also work with customized BTS to extend capa

city of original BTS with a low system total cost. This product platform features:

• Support multi-carrier CDMA signals, with mixed mode operation

• Output maximum power 160W, support carriers number up to 4.

• Very High System Efficiency

• Extensive product monitoring and control (local and remote)

• Centralized system control/display/alarms

• Great system reliability supported by architecture built-in redundancy

• Powered by 30VDCavailable

• Extensive protection for lightning, voltage surge, and any high failure rate assemblies

• Compact system size and light weight

2. System Block Diagram

Summary of content (7 pages)

PAGE 1
LPA2100-160-SW01 LPA2100-160-SW01 SPECIFICATION 1. System advantages Bravo Tech Inc 's newly introduced Multi-Carrier High Power Outdoor Booster platform provides high er downlink EIRP and improved uplink sensitivity at the same time to extend the coverage of existing cellu lar networks. This multi-carrier based product platform can also work with customized BTS to extend capa city of original BTS with a low system total cost.
PAGE 2
LPA2100-160-SW01 3. Electrical Specifications PARAMETER Frequency Output Power Spurious Emission RF Gain SPECIFICATION 2110 ~ 2155 MHz 160Watts average max. ( CDMA2000, PAR：8.0dB) -45dBc@∆f=885-1.25MHz, 30kHz RBW -55dBc@∆f=1.25-1.98MHz, 30kHz RBW -55dBc@∆f=1.25-2.25MHz, 30kHz RBW -13dBm@∆f=2.25-4MHz, 30kHz RBW 57.0 ± 1.0dB @ frequency range, +30Vdc, room temp. Normal Operating Voltage +30Vdc±1.0Vdc Operating Voltage RF Gain Variation over Voltage & Temperature Gain Flatness +29Vdc ~ +31Vdc ±1.
PAGE 3
LPA2100-160-SW01 5. Description of the connectors 5.1 RF Part Port Name Type Warning Input SMA Female (50Ω) Output N Female (50Ω) Normal :-5.2dBm maxium input power +1dBm. Normal :51.76dBm maxium output power 52.5dBm. 5.2 DC power Port Name DC IN Type NO Warning D-Sub type DSCD175PS1M (Male) A1、A2 VDC A3、A4 GND to VDC type +30V, range 24~32V 5.3 Communication Connector type: USB Note: Manufacter use to debug. 5.
PAGE 4
LPA2100-160-SW01 5.5 Warning 1. Check the power supply voltage is between 24V and 32V or not before electrify, better to setup in 30V. Power of power supply shall bigger than 1400W. 2. Ensure the power supply polarity is right, port A1、A2 are anode, and port A3、A4 are cathode. 3. Ensure the output line is connected and input power is not over load before connect the RF input line. 4. Use the type N connector as output connector, for the high output power, suggest to using the φ3 upwards RF cable to connect.
PAGE 5
LPA2100-160-SW01 6. Dimension Front 345 Left Right 450 Unit: mm Rear Figure 2 Dimension BRAVO TECH INC Add.: 6185 Phyllis Drive Unit D, Cypress, CA 90630 Phone: 1-714-230-8333 Website: www.bravotechinc.com Revision: SP·LPA2100-160-SW01·REV.
PAGE 6
LPA2100-160-SW01 Figure 3 Mechanical drawing BRAVO TECH INC Add.: 6185 Phyllis Drive Unit D, Cypress, CA 90630 Phone: 1-714-230-8333 Website: www.bravotechinc.com Revision: SP·LPA2100-160-SW01·REV.
PAGE 7
LPA2100-160-SW01 7. Assembled 5 screws 4-40, L3/8 inch 3 screws 4-40, L5/8 inch Figure 4 Assembled Instructions 1. Lock 5 screws 4-40, L3/8 inch with Philip's type screwdriver to fasten the front side of PA to the Front Plate of Booster as shown above. 2. Lock 3 screws 4-40, L5/8 inch with Philip's type screwdriver to fasten the back side of PA to a connection board which is connected to the soleplate of Booster. BRAVO TECH INC Add.