Quick Start Guide

ManualsBrandsBTI Wireless ManualsElectronics5G CPE

CPX80P

Quick Start Guide

Introduction

CPX80P is a highly advanced 5G outdoor multi-service

product solution speciﬁcally designed to meet integrated data

needs for residential, business and enterprise users. The product

supports advanced Gigabit networking functionalities. It enables

wide service coverage and provides high data throughput and

networking features to customers who needs easy broadband

access.

Panel of device

Packing list

Make sure you have everything you need to properly conﬁgure the

device.

ODU PoE Ethernet cablePower supply

Stainless steel

clamp

Cable glands Slotted end cap

How does it work

1. Connect the Power Adapter to PoE injector.

2. PoE injector provides the power to ODU via LAN cable.

3. PC connects LAN Cable to PoE, then PC can surf the Internet

when ODU accesses the 5G network.

This quick installation guide shows you how to conﬁgure your ODU

in order to access the Internet.

Configure hardware

Please make sure that you are familiar with all

accident prevention and safety procedures

necessary for working at height and with electrici-

ty before starting to install the device.

DO NOT install the ODU during a lightning storm.

Insert a SIM card to the slot

Step 1 CAT6 (or above) cable to thread through the cable glands.

Step 2 Connect the end of the CAT6 (or above) Ethernet cable to the

PoE port of the ODU.

Step 3 Wiring the cable glands into ODU and seal tightly.

NOTE: Make sure you have inserted the SIM card into the ODU.

Mount the ODU

See the installation instructions to mount the ODU correctly.

Header connection

Mounting bracket

The ODU can be mounted on an antenna pole or mast or on a wall

using the supplied mounting bracket.

· Choose a mounting point that is sturdy enough to hold the ODU,

even during high winds.

· When choosing a location to install the ODU, please note that the

ODU’s front panel should point towards your service provider’s

nearest base station. You do not need to be able to see the base

station from the ODU’s position. However, if you experience

difﬁculties with signal reception, a Line of Sight (LoS) connection

may produce better results.

· It is suggested that you transport the ODU to its intended

installation location in its original protective package.

To obtain the best radio signal level and connection quality, the CPE

antenna should be aimed towards the best eNB or BS directly.To

search for the best eNB direction, the user can rotate the CPE slowly

and tilt CPE slightly to ﬁnd the best signal direction. The CPE radio

signal strength level can be observed from the RF LEDs mounted on

the lower panel as shown below. Different colored LEDs represent

different signal strength.

Choose location

Connect the PoE

Place a CAT6 (or above) Ethernet cable (not included) from the

location of your intended Router to the desired PC location.

If you intend to use cable clamps or other methods to secure the

cable, do not tighten them until you ﬁnish installing the Router and

ODU.

ODU

Computer

PoE Adapter

Hardware connections of Router

ODU

PWR

Steady on

Off

Power on

No power supply

NET

Steady on Internet available

Internet unavailable

Blinking

(500ms interval)

Searching network

Off

SIM

Steady on SIM ready

No SIM detected

Yellow

Green Signal strong

Signal good

Red

Signal weak

Off No signal

Blinking Green and Red

(500ms interval)

Firmware upgrade

SIG

Configure the CPE

Use a browser to access the management web page to conﬁgure

and manage the CPE.

The following procedure describes how to use a computer running

Windows 7 or above version and Internet Explorer to connect to the

CPE webpage.

Connect to the CPE correctly.

Start Internet Explorer, type http://192.168.225.1 in the

address bar, and press Enter.

Enter the user name and password, and click Log In.

You can connect to the management web page after the password

is veriﬁed.

Configuration of 5G

Step 1 Connect to the CPE correctly.

Step 2 Go to the management website.

Step 3 Choose Settings → Network → Radio Settings.

Step 4 Set the connection mode and scan mode.

The default setting is automatic connection and full band

scanning, if you want to connect to the 5G network according to

your needs, you can set the connection mode as manual, and simply

scan a speciﬁc band.

10 11 12 13

FAQs

· Make sure that the CPE is powered on.

· Verify that the CPE is correctly connected to the computer through

a network cable.

If the problem persists, contact authorized local service suppliers.

· Check that the power adapter and PoE have connected to the CPE

properly.

· Check that the CPE is placed in an open area that is far away from

obstructions, such as concrete or wooden walls.

· Check that the CPE is placed far away from household electrical

appliances that generate strong electromagnetic ﬁeld, such as

microwave ovens, refrigerators, and satellite dishes.

- If the problem persists, contact your Internet Service Provider.

· The CPE is hot after being used for long time. Turn off the CPE

when not in use.

· Check that the CPE is properly ventilated and protected from direct

sunlight.

Fails to Log in to the web management page.

· Make sure that the power cable is connected to the PoE, and the

CPE is connected to the right port of the PoE.

· Make sure that the power adapter and PoE are compatible with the

CPE.

The POWER indicator does not turn on.

The CPE fails to search for the 5G network.

The CPE power adapter has overheated

· If the CPE powers off unexpectedly while being conﬁgured, the

parameters may be restored to the default settings.

· After conﬁguring the parameters, download the conﬁguration ﬁle to

quickly restore the CPE to the desired settings.

The parameters are restored to default values.

Some features of the product and its accessories described herein

rely on the software installed, capacities and settings of local

network, and may not be activated or may be limited by local

network operators or network service providers, thus the descrip-

tions herein may not exactly match the product or its accessories

you purchase.

We reserve the right to change or modify any information or

speciﬁcations contained in this manual without prior notice or

obligation.

Notice

To connect the CAT6 (or above) Ethernet cable:

Step 1 Connect the CAT6 (or above) Ethernet cable to PoE.

Step 2 Connect the power adapter to the PoE injector. The POWER

LED turns on a solid green once connected.

Step 3 Connect the included Ethernet cable from the computer to

one of the Router's Ethernet ports.

LED behavior

When setting up the Outdoor Unit, the LED will have the following

behavior:

Do not connect to a computer or switch directly

to the PoE port due to high PoE power.

CAUTION

Make sure the ODU is turned off before you insert

your SIM card. It is recommended to NOT connect

the PoE cable when you do this step. Otherwise, the

SIM card may be damaged.

CAUTION

Step 1

Step 2

Step 3

5G CPE

FCC statement

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

FCC radiation exposure statement

This device complies with FCC radiation exposure limits set forth for

an uncontrolled environment and it also complies with Part 15 of the

FCC RF Rules. This equipment must be installed and operated in

accordance with provided instructions and the antenna(s) used for

this transmitter must be installed to provide a separation distance of

at least 26

cm from

all persons and must not be co-located or

operating in conjunction with any other antenna or transmitter.

End-users and installers must be provided with antenna installation

instructions and consider removing the no-collocation statement.

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including

interference that may cause undesired operation.

Caution!

Any changes or modiﬁcations not expressly approved by the party

responsible for compliance could void the user's authority to

operate the equipment.

· I/O panel of ODU ·