Dual Digital Drive CD-RW 5232IA User’s Manual
CLASS 1 LASER PRODUCT APPAREIL A LASER DE CLASSE 1 LASER KLASSE 1 LUOKAN 1 LASERLAITE PRODUIT LASER CATEGORIE 1 DANGER VORSICHT INVISIBLE LASER RADIATION WHEN OPEN AVOID DIRECT EXPOSURE TO BEAM INSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET NICHT DEM STRAHL AUSSETSEN ATTENTION RADIATION DU FAISCEAU LASER INVISIBLE EN CAS D’OUVERTURE. EVITER TOUTE EXPOSITION AUX RAYONS.
FCC Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. this device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation. FCC Warning Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Table of Contents INTRODUCTION SYSTEM REQUIREMENTS PACKAGE CONTENTS INSTALLATION HOST INTERFACE CONNECTIONS HARDWARE INSTALLATION DRIVER INSTALLATION For the CD-RW Drive For the Card Reader SOFTWARE INSTALLATION Windows Environment CONNECTION & OPERATION FRONT PANEL REAR VIEW TECHNICAL DATA 1 2 2 3 3 4 6 6 6 9 9 10 10 12 14
Dual Digital Drive INTRODUCTION Thank you for the purchase of CD-RW 5232IA, a perfect and compact dual storage drive with the combination of an IDE CD-ReWritable drive and a USB-connected card reader. CD-RW 5232IA backs up all writing modes and different CD formats. It supports maximum 52x speed writing ability on CD-R discs, 32x speed on CD-RW discs and 52x speed reading performance.
Dual Digital Drive System Requirements For IBM compatible PCs, the system requirements recommended are as follows: ♦ Pentium II 350MHz above with at least 64MB of memory ♦ Fast and sufficient hard disk space (minimum 200MB for installation, 1GB or more is recommended.
Dual Digital Drive INSTALLATION Host Interface Connections Most current mainboards have two IDE ports (primary and secondary) which can connect two IDE cables. Two IDE cables allow you to connect up to four devices, but it is recommended that you separate IDE ports for your hard drive and your CD-ReWritable drive. This will ensure that your hard drive’s performance and speed won’t be affected by having the CDRW drive on the same cable.
Dual Digital Drive Hardware Installation 1. Turn off the power to the computer system. 2. Disconnect the power cord and all cables from the back of your computer, and then remove the cover of the computer. 3. Insert the drive into one of the vacant 5.25" drive bays and secure it with screws to your PC. 4. Connect one end of the 40-pin IDE cable to the IDE connector of this drive and the other end to the IDE port on your mainboard. Also, connect the power supply cable to the back of the drive.
Dual Digital Drive 6. Connect the USB cable at the back of the drive to the USB connector on the mainboard. The red wire of the cable needs to plug into Pin 1 on the board. This drive supports USB 1.1 and if you connect to USB 2.0 connector, only transfer rate of USB 1.1 will be available. USB RED WIRE IDE RED WIRE MOTHER BOARD 7. Re-attach the cover of your computer, and reconnect the power cord and all cables.
Dual Digital Drive Driver Installation For the CD-RW Drive For the CD-RW drive itself of CD-RW 5232IA, it is an IDE device supporting Plug & Play, and Windows 98SE/ME/2000/XP can automatically detect the drive and load the appropriate driver. For the Card Reader Windows 98SE/2000 If you run Window 98SE or 2000, please install the provided driver: 6 1. Insert the application disc. 2. Select:\Card Reader Driver 3. Click “setup.
Dual Digital Drive Click “OK” if you have already had USB cable connected (Refer to Hardware Installation, Step 6.
Dual Digital Drive Make sure to restart your computer. Windows ME/XP Since Windows ME and XP already have USB Mass Storage support, the card reader can be detected and work fine without installing driver. However, we recommend that you install the provided driver to have more explicit operation status of the card reader, as described below. For Windows XP users, please upgrade to Service Pack 1.
Dual Digital Drive After the driver installation, 4 extra icons with different card type indicated will show in Device Manager/My computer. And then you can use each slot of the card reader for file archiving/recording. While the card reader is reading data of memory cards, the icon for the card accessed will light up and the LED beside the card slot on the front panel will flash Green. Software Installation The bundled mastering software gives you the complete solution for making audio/data CDs.
Dual Digital Drive CONNECTION & OPERATION Front Panel 2 5 1 11 7 8 3 4 6 9 10 1. Headphone Jack By plugging in the headphone jack here, you can listen to an audio CD (CD-DA disc) directly playing from the drive. 2. Headphone Volume Control This knob adjusts the audio output level. Turn the wheel to the right/left for the volume control of your headphone. 3. Play/Skip button Press this button to play tracks or skip to next track during the playing state. 4.
Dual Digital Drive Flashes “red” while writing a CD-R/CD-RW disc. 6. LED Indicator (card reader) Once the USB cable is correctly connected, this LED will light yellow, which means the card slots are ready to use. 7. Slot for Memory Stick (MS)/Memory Stick Pro (MS Pro) 8. Slot for Secure Digital (SD)/MultiMediaCard (MMC) 9. Slot for Compact Flash(CF) Type I, II/MicroDrive 10. Slot for Smart Media 11.
Dual Digital Drive Rear View 3 4 5 6 1. Digital Audio Output Connector If your sound card has a digital audio IEC958 format connector, you can connect it to this digital audio output connector with a 2-pin audio cable. 2. Analog Audio Output Connector This connector allows you to connect the drive to your sound card with a 4-pin audio cable. 3. Device Configuration Jumper Set the jumper to Master, Slave or Cable Select according to your system configuration. 4.
Dual Digital Drive 5. Power Supply Connector By plugging the computer’s power supply cable here, you can connect the drive and your computer system. 6. USB Cable Connect the USB cable to the USB connector on the mainboard. The red wire of the cable needs to plug into Pin 1 on the board.
Dual Digital Drive TECHNICAL DATA Interface CD-RW Drive: IDE Card Reader: USB 1.1 Form factor 5.
Dual Digital Drive Access time 90ms at ⅓ stroke(52X CD-ROM) 180ms at full stroke(52X CD-ROM) 99ms at ⅓ stroke (32X CD-RW) 200ms at full stroke (32X CD-RW) Disc loading Tray (motorised), Dust Sealed Audio output level Line out = 0.6 ± 10%Vrms Headphone out = 0.6± 10%Vrms Power 5 VDC & 12VDC Card Reader power directly from computer power supply through USB connection Dimensions Height 41.8 ± 0.2 mm Width 148.8 ± 0.2 mm Depth 193.4 ± 0.
Dual Digital Drive Environment CD-RW Drive Temperature Operating Non-operating 5°C to 45°C -20°C to 60°C Humidity Operating 8% ~ 80%RH Non-operating 5% ~ 95%RH Card Reader Temperature Operating Non-operating 0°C to 40°C -20°C to 45°C Humidity 16 Operating 0% ~ 90%RH Non-operating 0% ~ 95%RH
3100551760 Version 1.