Operation Manual

ManualsBrandsBrunswick ManualsElectronicsSmartCraft Connect

Table Of Contents

SmartCraft Connect Gateway Operation Manual

SMARTCRAFT CONNECT GATEWAY

OPERATION MANUAL

IMPORTANT: This document guides our dealers, boatbuilders, and company service personnel in the proper installation or

service of our products. If you have not been trained in the recommended servicing or installation procedures for these or

similar Mercury Marine products, have the work performed by an authorized Mercury Marine dealer technician. Improper

installation or servicing of the Mercury product could result in damage to the product or personal injury to those installing or

operating the product.

Components in Kit

NOTE: The termination band on the 10‑pin connector cable only applies to under cowl mounted modules.

a - SmartCraft Connect module

b - SmartCraft Connect module ‑ side view

c - Cable ties ‑ 4

d - #10 x .88" stainless steel wood screw

Features

The CAN light and NMEA light will turn on when data is being transmitted through the Gateway.

NOTE: This manual covers the installation of CAN P only ‑ engine mounted module (single). The helm mount module will

default out of the box to CAN P ,and must be dealer or OEM configured to use CAN H. CAN P and CAN H are applicable to

single, dual, triple, and quad engines.

TERMINATED

ENGINE MOUNT ONLY

71911

Summary of content (5 pages)

PAGE 1
SMARTCRAFT CONNECT GATEWAY OPERATION MANUAL IMPORTANT: This document guides our dealers, boatbuilders, and company service personnel in the proper installation or service of our products. If you have not been trained in the recommended servicing or installation procedures for these or similar Mercury Marine products, have the work performed by an authorized Mercury Marine dealer technician.
PAGE 2
SMARTCRAFT CONNECT GATEWAY OPERATION MANUAL SmartCraft Connect Module—Single through Quad Engine NOTE: The Connect module does not provide power for any device on the NMEA 2000 network. The NMEA 2000 network will require its own power source. The NMEA power input must have appropriate circuit protection for the devices on the NMEA 2000 network. NOTE: The termination band on the 10‑pin connector cable only applies to under cowl mounted modules.
PAGE 3
SMARTCRAFT CONNECT GATEWAY OPERATION MANUAL 2. Connect the module NMEA 2000 harness connector to the NMEA 2000 network. b abcde- c e 120 TERMINATED ENGINE MOUNT ONLY 120 a 120K ohm termination resistor Chartplotter SmartCraft Connect module NMEA 2000 fused power source SmartCraft junction box a d 71914 Troubleshooting LED Lighting The device contains 5 LEDs for indicating the status of CAN P, NMEA, CAN H, WIFI, and Bluetooth. 1. 2. 3. 4. 5.
PAGE 4
SMARTCRAFT CONNECT GATEWAY OPERATION MANUAL Mercury Engine Data to NMEA 2000 Capable Products Signal Special Information NMEA 2000 PGN Mode Rated RPM 127498/0x1F20A TX Coolant pressure 127489/0x1F201 TX Speed over water (paddle and pitot) 128259/0x1F503 TX RPM (rapid update) 127488/0x1F200 TX Voltage 127489/0x1F201 TX Coolant temperature 127489/0x1F201 TX Fuel pressure 127489/0x1F201 TX Fuel level (percent, type) 2 tanks per engine up to 4 engines, tank 1 for each engine is type fuel 0X00,
PAGE 5
SMARTCRAFT CONNECT GATEWAY OPERATION MANUAL Cet appareil est conforme aux normes RSS exemptes de licence d'Innovation, Science et Développement économique Canada. Son fonctionnement est soumis aux deux conditions suivantes: 1) cet appareil ne doit pas provoquer d'interférences, et 2) cet appareil doit accepter toute interférence, y compris les interférences susceptibles de provoquer un fonctionnement indésirable de l'appareil.