FuGui Precision Industrial (Nanning) Co., LTD. No.51, Tongle Boulevard, Shajing, Jiangnan District, Nanning, P. R. CHINA Tel: 86-0771-2168888 Ext:30717 FAX: 86-0771-2168888 Ext:64886 1. Level 1 Environment-related Substances should NEVER be used. 2. Purchase ink, paint, wire rods, and molding resins only from the business partners that Sony approves as Green Partners. 3. Recycled Resin and Coated Wire should be procured from Green Partners Draft Approval Sheet IEEE802.11a/b/g/n/ac (1x1)+BT 5.
Revision History Date 2020/05/29 Revision Description 0.1 Initial release (draft version) 2020/09/02 0.2 1. Add module country of origin and manufacturing plant information. 2. Update BT from BT4.2 to BT5.0 3. Update temperature and humidity define and Logic Characteristics4. Add section 2.4 for current consumption 5. Add indicate description for access timing of SDIO in section 2.6 6.
Content 1. INTRODUCTION .......................................................................................................................................................... 4 2. ELECTRICAL SPECIFICATION ................................................................................................................................ 5 2.1 ABSOLUTE MAXIMUM RATING .................................................................................................................................. 5 2.
1. Introduction The T99H209.00 WLAN/BT module is IEEE802.11a/b/g/n/ac compatible, Bluetooth 5.0 compatible ,This module is based on Broadcom CYW4373IUBGT solution that integrated single-stream IEEE 802.11a/b/g/n/ac MAC/baseband/radio and Bluetooth5.0 (Basic Rate, Enhanced Data Rate and Bluetooth Low Energy) , it is designed with SDIO2.0 for WLAN and a high-speed 4-wire UART for BT as host interface. It supports below function: 1. WLAN 1x1 IEEE802.11a/b/g/n/ac supported BW for 2.
2. Electrical Specification 2.1 Absolute Maximum Rating These specifications indicate levels where permanent damage to the device can occur. Functional operation is not guaranteed under these conditions. Operation at absolute maximum conditions for extended can adversely affect long-term reliability of the device. Symbol Condition Respect to GND 3.3V Max Ripple on Supplied Voltage ESD Limit Level Min. Typ. Max -0.5 3.3 3.9 [1] Unit V 3.
2.4 Current Consumption Testing condition: 1.The current testing is just measured by 3.3V @ 25 C. 2. The current measured by KEYSIGHT 6705C ° Condition Voltage Current consumption RMS Peak Unit WiFi 2.4G +BT current WLAN 2.4G-TX 3.3V TBD 800 WLAN 2.4G-RX 3.3V TBD 800 WiFi 5G +BT current WLAN 5G-TX + BT TX 3.3V TBD 800 5G TX: VHT80_MCS0_14dBm 5G RX:11ac VHT80 MCS9 BT TX: DH5_4dBm BT RX: 3DH5 WLAN 5G-RX + BT RX 3.3V TBD 800 WLAN 5G-TX + BT RX 3.3V TBD 800 WLAN 5G-RX + BT TX 3.
2.5 Host Interface Specification 2.5.1 SDIO 2.0 Characteristics The SDIO interface supports all of the SDIO version 2.0 modes: DS: Default speed (DS) up to 25 MHz, including 1- and 4-bit modes (3.3 V signaling). HS: High speed up to 50 MHz (3.3 V signaling) 2.5.1.
2.5.1.
2.5.2 UART Characteristics The UART is a standard 4-wire interface (RX, TX, RTS, and CTS) with adjustable baud rates from 9600 bps to 4.0 Mbps. The interface features an automatic baud rate detection capability that returns a baud rate selection. UART timing specification: 2.6 Power up sequence VDD_3.3V should not rise 10%–90% faster than 40 microseconds. VDd_3.3V should be up before or at the same time as VDDIO.
2.7 WiFi RF Specification 2.7.1 IEEE802.11b Mode Radio Technology Direct Sequence Spread Spectrum (DSSS) Operating Frequency 2412 ~ 2462MHz Modulation Schemes DQPSK, DBPSK and CCK Channel Numbers 13 channels Data Rate 1Mbps , 2Mbps, 5.5Mbps and 11Mbps Media Access Protocol (MAC) CSMA/CA (Carrier Sense Multiple Access with Collision Avoidance) Transmitter Output Power 17 +/-1.5dBm for all data rate.
Maximum Receiver Sensitivity Level ≥ –20dBm @ 10% PER 6Mbps ≤ –5dB 9Mbps ≤ –8dB 12Mbps ≤ –10dB EVM 18Mbps ≤ –13dB 24Mbps ≤ –16dB 36Mbps ≤ –19dB 48Mbps ≤ –22dB 54Mbps ≤ –25dB 2.7.3 IEEE802.11n (HT20) Mode Radio Technology Orthogonal Frequency Division Multiplexing (OFDM) Operating Frequency 2412 ~ 2462MHz Modulation Schemes BPSK, QPSK, 16-QAM, 64-QAM Channel Numbers 13 channels Data Rate HT20 MCS0~MCS7 800ns GI: 6.5, 13, 19.5, 26, 39, 52, 58.5 and 65Mbps 400ns GI: 7.2, 14.4, 21.7, 28.9, 43.
2.7.4 IEEE802.11n (HT40) Mode Radio Technology Orthogonal Frequency Division Multiplexing (OFDM) Operating Frequency 2422 ~ 2462MHz Modulation Schemes BPSK, QPSK, 16-QAM, 64-QAM Channel Numbers 9 channels Data Rate HT40 MCS0~MCS7 800ns GI: 13.5, 27, 40.5, 54, 81, 108, 121.5 and 135Mbps 400ns GI: 15, 30, 45, 60, 90, 120, 135 and 150Mbps Media Access Protocol (MAC) Transmitter Output Power CSMA/CA (Carrier Sense Multiple Access with Collision Avoidance) 13 +/-1.
2.7.5 IEEE802.11a Mode Radio Technology Orthogonal Frequency Division Multiplexing (OFDM) Operating Frequency 5180 ~ 5825MHz Modulation Schemes BPSK, QPSK, 16-QAM, 64-QAM Channel Numbers 25 channels Data Rate 6 ,9, 12, 18, 24, 36, 48, and 54Mbps Media Access Protocol (MAC) CSMA/CA (Carrier Sense Multiple Access with Collision Avoidance) Transmitter Output Power 14+/-1.5dBm for 6~48Mbps 13+/-1.
Frequency Accuracy +/-20ppm Minimum Receiver Sensitivity Level MCS0 ≤ -87dBm@ 10% PER (*1) MCS1 ≤ -84dBm@ 10% PER MCS2 ≤ -82dBm@ 10% PER MCS3 ≤ -79dBm@ 10% PER MCS4 ≤ -75dBm@ 10% PER MCS5 ≤ -72dBm@ 10% PER MCS6 ≤ -71dBm@ 10% PER MCS7 ≤ -70dBm@ 10% PER Maximum Receiver Sensitivity Level ≥ –30dBm @ 10% PER EVM MCS0 ≤ -5dB MCS1≤ -10dB MCS2 ≤ -13dB MCS3 ≤ -16dB MCS4 ≤ -19dB MCS5 ≤ -22dB MCS6 ≤ -25dB MCS7 ≤ -27dB 2.7.7 IEEE802.
Maximum Receiver Sensitivity Level ≥ –30dBm @ 10% PER EVM (Test condition: Enable full packet channel estimate) MCS0≤ -5dB MCS1≤ -10dB MCS2 ≤ -13dB MCS3 ≤ -16dB MCS4≤ -19dB MCS5 ≤ -22dB MCS6 ≤ -25dB MCS7 ≤ -27dB 2.7.8 IEEE802.11ac (VHT20) Mode Radio Technology Orthogonal Frequency Division Multiplexing (OFDM) Operating Frequency 5180~5825MHz Modulation Schemes BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM Channel Numbers 25 channels Data Rate VHT20 MCS0~MS8 800ns GI: 6.5, 13, 19.5, 26, 39, 52, 58.
MCS5≤ -22dB MCS6 ≤ -25dB MCS7≤ -27dB MCS8≤ -30dB 2.7.6 IEEE802.11ac (VHT40) Mode Radio Technology Orthogonal Frequency Division Multiplexing (OFDM) Operating Frequency 5190~5795MHz ISM band Modulation Schemes BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM Channel Numbers 18 channels Data Rate VHT40 MCS0~MCS9 800ns GI: 13.5, 27, 40.5, 54, 81, 108, 121.
2.7.7 IEEE802.11ac VHT80 Mode Radio Technology Orthogonal Frequency Division Multiplexing (OFDM) Operating Frequency 5210~5775 MHz Modulation Schemes BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM Channel Numbers 9 channels Data Rate VHT80 MCS0~MCS9 800ns GI: 29.3, 58.5, 87.8, 117, 175.5, 234, 263.3 and 292.5, 351 and 390Mbps 400ns GI: 32.5, 65, 97.5, 130, 195, 260, 292.5, 325, 390, 433.
2.8 BT RF Specification BT Radio Modulation Operating Frequency Channel Numbers FHSS 2.402GHz ~ 2.480GHz 79 channels with 1MHz BW BDR Transmitter Output Power BDR Power Control BDR Initial Carrier Freq.
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. KDB 996369 D03 OEM Manual v01 rule sections: 2.2 List of applicable FCC rules This module has been tested for compliance to FCC Part 15.247 and Part 15.407 2.
2.9 Information on test modes and additional testing requirements This transmitter is tested in a standalone mobile RF exposure condition and any co-located or simultaneous transmission with other transmitter(s) or portable use will require a separate class II permissive change re-evaluation or new certification. 2.
this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable.
configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization.
in section 6.2.2.3 shall be clearly indicated.
