Software User’s Guide For DCP users; This documentation is for both MFC and DCP models. Where it says 'MFC' in this user's guide, please read 'MFC' as 'DCP'. Not all models are available in all countries.
Applicable models This User’s Guide applies to the following models. DCP-J4110DW, MFC-J2310/J2510/J4310DW/J4410DW/J4510DW/J4610DW/J4710DW Definitions of notes We use the following icons throughout this User’s Guide: IMPORTANT IMPORTANT indicates a potentially hazardous situation which, if not avoided, may result in damage to property or loss of product functionality. NOTE Notes tell you how you should respond to a situation that may arise or give tips about how the operation works with other features.
Table of Contents Section I 1 Windows® Printing 2 Using the Brother printer driver..................................................................................................................2 Features ....................................................................................................................................................2 Choosing the right type of paper................................................................................................................
Scanning a document using the TWAIN driver........................................................................................38 Scanning a document into the computer ...........................................................................................38 Pre-Scanning to crop a portion you want to scan..............................................................................40 Auto Crop .............................................................................................................
Accessing Address Book (For MFC models).....................................................................................74 Configuring the Scan button settings.................................................................................................75 Launching the BRAdmin utility...........................................................................................................76 Support tab ..................................................................................................
Entering cover page information......................................................................................................101 Address Book ........................................................................................................................................102 Brother Address Book .....................................................................................................................103 Setting up a member in the Address Book ........................................
9 Scanning 145 Scanning a document using the TWAIN driver......................................................................................145 Accessing the TWAIN driver............................................................................................................145 Scanning an image into your computer ...........................................................................................146 Pre-Scanning an image ......................................................................
Using the Scan button over a USB cable connection ............................................................................187 Scan to E-mail .................................................................................................................................188 Scan to Image .................................................................................................................................189 Scan to OCR ...........................................................................
Section I ® Windows Printing Scanning ControlCenter4 Remote Setup (For MFC models) Brother PC-FAX Software (For MFC models) PhotoCapture Center™ Firewall settings (For Network users) I 2 38 60 96 98 114 116
1 Printing 1 1 NOTE • The screens in this section are from Windows® 7. Screens on your computer may vary depending on your operating system. • If your computer is protected by a firewall, and you are unable to network print, network scan or PC-Fax, you may need to configure the firewall settings. If you are using the Windows® Firewall and you installed MFL-Pro Suite from the CD-ROM, the necessary Firewall settings have already been made.
Printing Choosing the right type of paper 1 1 For high quality printing, it is important to choose the right type of paper. Be sure to read Loading paper and Loading documents in the Basic User’s Guide before buying paper, and to determine the printable area depending on the settings in the printer driver. Simultaneous printing, scanning and faxing 1 Your machine can print from your computer while sending or receiving a fax in memory, or while scanning a document into the computer.
Printing Status Monitor 1 1 The Status Monitor utility is a configurable software tool for monitoring the status of one or more devices, allowing you to get immediate notification of error messages such as paper empty, paper jam or ink replacement required. You can check the device status at anytime by double-clicking the icon in the tasktray or by choosing Status Monitor located in /All Programs/Brother/MFC-XXXX on your computer. There is also a link to the Brother Original Supplies website.
Printing The red icon indicates an error has occurred. 1 The grey icon indicates the machine is offline. The Status Monitor can be displayed in the tasktray or on the desktop of your computer. Popup on Error 1 Popup on Error lets you know if there is a problem with a device that your computer is monitoring. The default setting is On. If you want to turn off Popup on Error, follow these steps: a Right-click the Brother Status Monitor icon or window and click Popup on Error to clear the check mark.
Printing Printer driver settings 1 1 You can change the following printer settings when you print from your computer: Media Type Print Quality Paper Size Orientation 2-sided / Booklet Colour / Greyscale Ink Save Mode Scaling Accessing the printer driver settings a b 1 From an application such as Microsoft® Notepad, click File, then Print in your application. Choose Brother MFC-XXXX Printer (where XXXX is your model name) and click Preferences. The printer driver window appears.
Printing Basic tab 1 1 1 2 3 4 5 6 19 7 8 9 10 11 12 13 14 15 16 17 20 18 1 Media Type drop-down list 2 Slow Drying Paper check box 3 Print Quality drop-down list 4 Paper Size drop-down list 5 Borderless check box 6 Colour Mode option 7 Orientation option 8 Copies option 9 Collate check box 10 Reverse Order check box 11 Multiple Page drop-down list 12 Page Order drop-down list 13 Border Line drop-down list 14 2-sided / Booklet drop-down list 15 2-sided Settings button 16 Paper Source drop-down list
Printing 19 Current settings view 1 20 Print Preview check box a Choose your settings for Media Type, Slow Drying Paper and Print Quality. NOTE Check Slow Drying Paper when printing with plain paper on which ink dries slowly. This setting may cause some slight blurring of text. b Choose Paper Size, Borderless, Colour Mode, Orientation, number of Copies and the page order, Collate, Reverse Order, Multiple Page, Page Order, Border Line and 2-sided / Booklet (if required).
Printing Fast 1 The fastest print mode and the lowest amount of ink used. Use for printing large volume documents or documents for proofing.
Printing 1 NOTE • Depending on the user defined size, you may only be able to print using the manual feed slot. • The paper orientation (portrait or landscape) varies depending on the paper size. See Basic User’s Guide. To do borderless printing 1 Check the Borderless check box. Colour Mode 1 Colour is adjusted to get the closest colour match with the monitor. Natural: Use for photographic images. The colour is adjusted to print more natural colours.
Printing NOTE 1 If your application software contains a similar function to this, we recommend you use the one in the application. Copies 1 The Copies selection sets the number of copies that will be printed (1 to 999). Collate 1 With Collate checked, one complete copy of your document will be printed and then reprinted according to the number of copies you choose.
Printing Page Order 1 1 When the N in 1 option is selected, the Page Order can be selected from the drop-down list. Border Line 1 When the N in 1 option is selected, you can choose to have a solid border, dashed border or no border around each page on the sheet. 2-sided / Booklet 1 When you want to print a booklet or do 2-sided printing, use this function. None Disable 2-sided printing. 2-sided The machine prints on both sides of the paper automatically.
Printing • Binding Offset 1 When you check Binding Offset, you can also specify the offset for binding in inches or millimetres. NOTE The Borderless feature is not available for 2-sided printing and booklet printing. Paper Source (For MFC-J4610DW/J4710DW) 1 You can choose Auto Select, Tray1 or Tray2 as Paper Source. If you put one sheet of paper in the manual feed slot, the paper from the slot is automatically chosen.
Printing 2 Preview Area The Preview Area displays a preview of the print results for the pages chosen in the Page List Area. 1 NOTE • If the Booklet setting was chosen in the Printer driver settings, you cannot use the Print Preview function. • If the 2-sided setting was chosen in the Printer driver settings, you cannot delete pages using the Page List Area.
Printing Advanced tab 1 1 1 2 3 4 5 6 7 8 9 10 11 1 Colour / Greyscale option 2 Colour Settings button 3 Ink Save Mode check box 4 Scaling option 5 Mirror Print check box 6 Reverse Print check box 7 Use Watermark check box 8 Header-Footer Print check box 9 Other Print Options button 10 Default button 11 OK button a b c Choose your setting for Colour / Greyscale. Choose Ink Save Mode to help reduce ink consumption. Choose your setting for the Scaling feature.
Printing d You can choose reverse printing options. 1 Check Mirror Print to reverse the data from left to right. Check Reverse Print to reverse the data from up to down. NOTE Mirror Print is not available when choosing Transparencies as a Media Type. e You can print a logo or text onto your document as a watermark. You can choose one of the preset watermarks, or you can use a bitmap file or text file that you have created.
Printing Colour Enhancement 1 1 This feature analyzes your image to improve its sharpness, white balance and colour density. This process may take several minutes depending on the size of the image and the specifications of your computer. Colour Density Adjusts the total amount of colour in the image. You can increase or decrease the amount of colour in an image to improve a washed out or weak-looking picture. White Balance Adjusts the hue of the white areas of an image.
Printing 1 Ink Save Mode: Off 1 Ink Save Mode: On 1 (The above screens are used in ISO/IEC 24712.) Use Watermark 1 You can print a logo or text onto your document as a watermark. You can choose one of the preset watermarks, or you can use a bitmap file or text file that you have created. Check Use Watermark and then click Settings on the Advanced tab.
Printing Watermark Settings 1 1 Choose a watermark you want to use or edit from Select Watermark. Transparent 1 Check Transparent to print the watermark image in the background of your document. If this feature is unchecked, the watermark is printed at the front of your document. In Outline Text 1 Check In Outline Text if you only want to print an outline of the watermark. This feature is available when choosing a text watermark.
Printing 1 You can change the watermark settings with this feature. If you want to add a new watermark, enter Title and then choose Use Text or Use Bitmap File in Watermark Style. Title Enter a suitable title into the field when adding a new watermark. Your chosen watermark is overwritten with this title. Text Enter your watermark text in the Text box, then choose Font, Style, Size and Choose Colour.
Printing Header-Footer Print 1 1 You can print the date and time from your computer's system clock, and the computer login user name or your entered text on your document. To customize the settings, click Settings on the Advanced tab. ID Print 1 You can choose your computer login user name or your entered text as a header or footer from the following ways: Choosing Login User Name to print your computer login user name. Choosing Custom to print your entered text in the Custom text box.
Printing Other Print Options 1 1 Click Other Print Options on the Advanced tab to set more printer functions. NOTE The screen shown in this section may vary depending on your machine. Change Data Transfer Mode 1 The Change Data Transfer Mode feature lets you choose a print data transfer mode to improve print quality or print speed. Recommended Setting Choose Recommended Setting for general use. Improved Print Quality Choose Improved Print Quality for better print quality.
Printing Advanced Colour Settings 1 1 You can set the Halftone Pattern and Match Monitor for more colour adjustment. Halftone Pattern The machine can use two methods (Diffusion or Dither) to arrange dots to express halftones. There are some predefined patterns and you can choose which one to use for your document. • Diffusion Dots are put at random to create the halftones. Use for printing photographs that have delicate shades and graphics.
Printing Advanced 2-sided Settings 1 1 Some types of print media may need more drying time when using the 2-sided feature. Change Advanced 2-sided Settings if you have problems with smudged 2-sided prints or paper jams. Normal Choose Normal to print at a typical speed, using a normal amount of ink. 2-sided 1 (Slower print speed) Choose 2-sided 1 to print at a slower speed, using a normal amount of ink.
Printing Retrieve Printer’s Colour Data 1 This setting helps to optimize print quality by retrieving colour data from your specific device. Use this option when you replace the device or change the network connected device. Use Printer’s Colour Data Check this box if you want to use the printer’s colour data. Remove the check mark if you do not want to use the information. Retrieve Printer’s Colour Data If you click this button, the printer driver starts retrieving the colour data of your device.
Printing • When an error message dialog box appears, confirm that your computer and your Brother machine are correctly connected, and then retry. • After retrieving the printer’s colour data, your computer will save the data and apply it to printing. • If your Brother machine is connected to multiple computers, do this feature on each computer connected. • You can retrieve the printer’s colour data only from the printer server if the printer is shared.
Printing Print Profiles tab 1 1 Print Profiles are editable presets designed to give you quick access to frequently used printing configurations. 6 1 2 5 3 4 1 Print profile list box 2 Delete Profile button 3 Always show Print Profiles tab first check box 4 OK button 5 Add Profile button 6 Current print profile view a b c Choose your profile from the print profile list box.
Printing Add Profile 1 1 The Add Profile dialog box appears by clicking Add Profile. You can add 20 new profiles with your preferred settings. a b c Enter the desired title in Name. Choose an icon you want to use from the Icon list, then click OK. The current settings shown on the left side of the printer driver window will be saved. Delete Profile 1 The Delete Profile dialog box appears by clicking Delete Profile. You can delete any of the profiles you have added.
Printing Maintenance tab 1 1 To maintain good print quality, the machine will automatically clean the print head when needed. You can also start the cleaning process manually if there is a print quality problem. Test Print You can print the test page and check the print quality. Standard Cleaning You can clean the machine’s print head manually. Clean the print head if a vertical line appears in text or graphics, or if blank spaces appear in the text on printed pages.
Printing Support 1 1 The Support window shows the driver version and settings information. There are also links to the Brother Solutions Center and Original Supplies Website. Click Support on the printer driver window to display the Support window: Brother Solutions Center The Brother Solutions Center is a website offering information about Brother product including FAQs (Frequently Asked Questions), user’s guide, driver updates and tips for using your machine.
Printing Using FaceFilter Studio for photo printing by REALLUSION 1 FaceFilter Studio is an easy-to-use borderless photo printing application. FaceFilter Studio also lets you edit your photo data. You can add photo effects such as red eye reduction or skin tone enhancement. To use FaceFilter Studio, you must install the FaceFilter Studio application from the CD-ROM supplied with your machine.
Printing Starting FaceFilter Studio with your Brother machine turned on 1 1 a When you launch FaceFilter Studio for the first time, this screen will appear, if your Brother machine is turned on, and connected to your computer, the FaceFilter Studio will detect your Brother machine. b After you click Continue in step a, this screen will appear. FaceFilter Studio is ready to use with full functionality.
Printing Starting FaceFilter Studio when your Brother machine is turned off 1 1 a When you launch FaceFilter Studio for the first time, if your Brother machine is turned off or not connected to your computer, this screen will appear. b Click Detect in step a, and this screen will appear. Turn on your Brother machine and check that it is connected to your computer and then click Yes. c If FaceFilter Studio does not detect the Brother machine, this screen will appear.
Printing e After you click the check mark in step d, FaceFilter Studio will start with limited functionality. The Print icon on the top menu will be greyed out and you will not be able to use the Print function. 1 NOTE • When FaceFilter Studio starts with limited functionality, the image file will be saved with a watermark. • To start FaceFilter Studio with full functionality, see Starting FaceFilter Studio with your Brother machine turned on on page 32.
Printing b Click the Print icon in the top menu bar to move to the print screen. 1 c Click the Print icon on the left to open the print settings dialog box. d Choose Paper Size, Paper Source, Orientation, number of Copies, Scaling and Printing Area. NOTE If you want to print a borderless photo, choose Full Page Photo in Scaling.
Printing e Click Print Setting and choose your Brother machine. Click OK. 1 NOTE If you want to use photo paper, click Properties and set the Media Type and Print Quality in the printer driver dialog box. f Click Print in the Print settings dialog box and your photo will print. Smart Portrait 1 The Smart Portrait function detects faces in the photo and adjusts the brightness of the skin tone automatically. a Open the image file.
Printing Print Expression List 1 1 FaceFilter Studio lets you modify a facial expression by applying an expression template or by manual adjustment. In the Select Expression step, you can preview or print the expression list of your choice. Uninstalling FaceFilter Studio 1 To uninstall FaceFilter Studio, choose /All Programs/Reallusion/FaceFilter Studio/Uninstall FaceFilter Studio.
2 Scanning 2 The scanning operations and the drivers used will be different depending on your operating system or the scanning application used. 2 Two scanner drivers are installed. A TWAIN compliant scanner driver (See Scanning a document using the TWAIN driver on page 38) and a Windows® Imaging Acquisition (WIA) driver (See Scanning a document using the WIA driver on page 47). Windows® XP/Windows Vista®/Windows ® 7 users can select either driver when scanning documents.
Scanning e Choose TWAIN: TW-Brother MFC-XXXX or TWAIN: TW-Brother MFC-XXXX LAN from the Available Scanners list. (Where XXXX is your model name.) f g Check the Display scanner dialog box on the Scan or Get Photo panel. h 2 Click Scan. The Scanner Setup dialog box appears.
Scanning • About 2-sided scanning (For MFC-J4710DW): You cannot adjust the scanning area. You cannot use PreScan to preview an image. 2 2-sided scanning is available from the ADF only. Pre-Scanning to crop a portion you want to scan 2 You can preview your image and crop unwanted portions before scanning by using the PreScan button. When you are satisfied with the preview, click Start on the Scanner Setup dialog box to scan the image.
Scanning e Load your document again. NOTE Skip this step if you loaded the document on the scanner glass in step a. f Click Start. This time only the chosen area of the document appears in the PaperPort™ 12SE window (or your application window). g In the PaperPort™ 12SE window, use the options available to refine the image. 2 Auto Crop 2 You can scan multiple documents placed on the scanner glass by checking Auto Crop.
Scanning Auto Crop is available for up to a maximum of 16 documents depending on the size of your documents. If you check Auto Crop, you cannot choose PreScan and 2-sided Scanning 1.
Scanning Settings in the Scanner Setup dialog box 2 Scan (Image Type) 2 2 Choose the output image type from Photo, Web or Text. Resolution and Scan Type will be automatically altered for each of the default settings.
Scanning 256 Colour Uses up to 256 colours to scan the image. 24bit Colour 2 Uses up to 16.8 million colours to scan the image. Although using 24bit Colour creates an image with the most accurate colour reproduction, the image file size will be about three times larger than a file created using the 256 Colour option. It requires the most memory and has the longest transfer time. Reduce Noise 2 You can improve and enhance the quality of your scanned images with this selection.
Scanning Document Size 2 Choose one of the following sizes: Auto You can scan a standard sized document without any further adjustments to Document Size. If you want to use Auto Crop, choose a Document Size other than Auto. A4 210 x 297 mm (8.3 x 11.7 in) JIS B5 182 x 257 mm (7.2 x 10.1 in) Letter 215.9 x 279.4 mm (8 1/2 x 11 in) Legal 215.9 x 355.6 mm (8 1/2 x 14 in) (Available on ADF models) A5 148 x 210 mm (5.8 x 8.3 in) JIS B6 128 x 182 mm (5 x 7.2 in) A6 105 x 148 mm (4.1 x 5.
Scanning NOTE You can see the actual paper size you chose on the screen. 2 • Width: shows the width of scanning area. • Height: shows the height of scanning area. • Data Size: shows the approximate data size in Bitmap format. The size will vary depending on the type of file, resolution and number of colours used.
Scanning Scanning a document using the WIA driver 2 WIA compliant 2 For Windows® XP/Windows Vista®/Windows® 7 you can choose Windows® Imaging Acquisition (WIA) when scanning images. You can scan images directly into the PaperPort™ 12SE viewer that Brother included with your machine or you can scan images directly into any other applications that support WIA or TWAIN scanning. NOTE (For MFC-J4710DW) Windows® XP does not support 2-sided scan in the WIA driver.
Scanning g Click Scan. The Scan dialog box appears. h Adjust the following settings, if needed, in the Scanner Setup dialog box: 2 1 2 3 4 5 6 1 Paper source 2 Picture type 3 Adjust the quality of the scanned picture 4 Page size 5 Preview 6 Scan i Choose Document Feeder or Flatbed from the Paper source drop-down list. NOTE If your machine has no Auto Document Feeder (ADF), you cannot choose Document Feeder. j k Choose the picture type. Choose the Page size from the drop-down list.
Scanning l If you want to change some advanced settings, click Adjust the quality of the scanned picture. You can choose Brightness, Contrast, Resolution and Picture type from Advanced Properties. Click OK after choosing the settings. 2 NOTE By default, the scanner resolution can be set to a maximum of 1200 dpi. If you want to scan at higher resolutions, use the Scanner Utility. (See Scanner Utility on page 50.) m Click Scan in the Scan dialog box. The machine starts scanning the document.
Scanning e Press and hold down the left mouse button and drag it over the portion you want to scan. 2 f If you need advanced settings, click Adjust the quality of the scanned picture. You can choose Brightness, Contrast, Resolution and Picture type from Advanced Properties. Click OK after choosing settings. g Click Scan in the Scan dialog box. The machine starts scanning the document. This time only the chosen area of the document appears in the PaperPort™ 12SE window (or your application window).
Scanning Running the utility You can run the utility by clicking the Scanner Utility located in /All Programs/Brother/MFC-XXXX menu (where XXXX is your model name)/Scanner Settings. Screens on your computer may vary depending on your operating system or the model of your machine. NOTE (Windows Vista® and Windows ® 7) When the User Account Control screen appears, do the following. • For users who have administrator rights: Click Allow or Yes.
Scanning Scanning a document using the WIA driver (Windows® Photo Gallery and Windows® Fax and Scan users) 2 2 Scanning a document into the computer 2 There are two ways to scan a whole page. You can either use the ADF (automatic document feeder) or the scanner glass. If you want to scan and then crop a portion of a page after pre-scanning the document, you must scan using the scanner glass. (See Pre-Scanning and cropping a portion using the scanner glass on page 54.) a b c Load your document.
Scanning f Adjust the following settings, if needed, in the Scanner dialog box: 1 2 2 3 4 5 6 7 10 8 9 11 12 1 Scanner 2 Profile 3 Source 4 Paper size 5 Color format 6 File type 7 Resolution 8 Brightness 9 Contrast 10 Scanning area 11 Preview 12 Scan NOTE • By default, the scanner resolution can be set to a maximum of 1200 dpi. If you want to scan at higher resolutions, use the Scanner Utility. (See Scanner Utility on page 50.
Scanning Pre-Scanning and cropping a portion using the scanner glass 2 The Preview button is used to preview an image for cropping any unwanted portions from the image. When you are satisfied with the preview, click Scan in the Scan dialog box to scan the image. a b c Put the document face down on the scanner glass. Follow the steps from b to e of Scanning a document into the computer on page 52. Choose Flatbed from the Source drop-down list. Adjust the settings, if needed, in the Scanner dialog box.
Scanning Using Nuance™ PaperPort™ 12SE 2 NOTE Nuance™ PaperPort™ 12SE supports Windows® XP (SP3 or higher), XP Professional x64 Edition (SP2 or greater), Windows Vista® (SP2 or higher) and Windows ® 7 only. 2 Nuance™ PaperPort™ 12SE for Brother is a document management application. You can use PaperPort™ 12SE to view scanned documents. PaperPort™ 12SE has a sophisticated, yet easy-to-use filing system that will help you organize your graphics and text documents.
Scanning As long as you have the appropriate application on your computer to display it, you can also open a nonPaperPort™ 12SE item by double-clicking it. 2 Organizing your items in folders 2 PaperPort™ 12SE has an easy-to-use filing system for organizing your items. The filing system consists of folders and items that you choose to view in Desktop. An item can be a PaperPort™ 12SE item or a nonPaperPort™ 12SE item: Folders are arranged in a ‘tree’ structure in the Folder View.
Scanning If PaperPort™ 12SE does not automatically recognise one of the applications on your computer, you can manually create a link using the New Link button from the Tools tab on the ribbon. Nuance™ PaperPort™ 12SE lets you convert image text into text you can edit 2 Nuance™ PaperPort™ 12SE can quickly convert a text document image into text that you can edit with a word processing application. PaperPort™ 12SE uses the optical character recognition software (OCR), which comes with PaperPort™ 12SE.
Scanning Uninstalling Nuance™ PaperPort™ 12SE 2 (Windows® XP) 2 a Click Start, Control Panel, Add or Remove Programs, and click the Change or Remove Programs icon. b Choose Nuance PaperPort 12 from the list and click Change or Remove. (Windows Vista® and Windows® 7) a Click the b Choose Nuance PaperPort 12 from the list and click Uninstall. 2 2 button, Control Panel, Programs and Programs and Features.
Scanning Using BookScan Enhancer and Whiteboard Enhancer by REALLUSION 2 BookScan Enhancer and Whiteboard Enhancer are image processing applications. BookScan Enhancer can automatically correct images scanned from books. Whiteboard Enhancer can clean up and enhance text and images in photos taken of a whiteboard. Installing BookScan Enhancer and Whiteboard Enhancer a b Insert the supplied CD-ROM into your CD-ROM drive. c Click BookScan&Whiteboard Suite. Follow the on-screen instructions.
3 ControlCenter4 3 Overview 3 ControlCenter4 is a software utility that lets you quickly and easily access your often used applications. Using ControlCenter4 eliminates the need to manually launch specific applications. 3 ControlCenter4 also controls the settings for the Scan button on your Brother machine.
ControlCenter4 Using ControlCenter4 in Home Mode 3 This section briefly introduces the ControlCenter4 function in Home Mode. For more details of each function, click (Help). 1 2 3 4 5 6 7 8 3 9 1 Print or edit images, attach images to E-mail, open images with an application and copy images from a memory card or USB Flash memory drive. 2 Scan directly to a file, E-mail, word processor or graphics application of your choice. 3 Access the PC-FAX applications available for your device.
ControlCenter4 ControlCenter4 Features for Home Mode users 3 Photo (See Photo tab on page 63.) See Copying images from a memory card or USB Flash memory drive on page 63. See Opening the ControlCenter4 folder tree on page 63. See Opening the folder tree on page 64. 3 See Printing images on page 64. See Editing images on page 64. See Attaching images to E-mail on page 65. See Opening images with an application on page 65. Scan (See Scan tab on page 66.) See File types on page 67.
ControlCenter4 Photo tab 3 There are five functions: Print, Edit, Open with an Application, Send E-mail and Photo Capture. This section briefly introduces these functions. For more details of each function, click (Help).
ControlCenter4 Opening the folder tree 3 The Desktop button lets you open the folder tree from the desktop to choose images you want to print, edit, attach to an E-mail or open with a specific application directly. Printing images The 3 (Print) button lets you print images. a Choose images you want to print by clicking the image from the image viewer, check the check box under the image, and then enter the number of copies you want to print (1 to 99).
ControlCenter4 Attaching images to E-mail The 3 (Send E-mail) button lets you attach images to your default E-mail application. a Choose images you want to attach to E-mail from the image viewer. b Click (Send E-mail), and your default E-mail application starts and shows a new E-mail with attachments. 3 NOTE The Send E-mail feature does not support Webmail services.
ControlCenter4 Scan tab 3 There are five scan options: Save, Print, Open with an Application, Send E-mail and OCR. This section briefly introduces the Scan tab function. For more details of each function, click 1 (Help).
ControlCenter4 File types 3 You can choose a file type to save the scanned image as from the following list: For Save and Send E-mail 3 Windows® Bitmap (*.bmp) 3 JPEG (*.jpg) TIFF (*.tif) TIFF Multi-Page (*.tif) Portable Network Graphics (*.png) PDF (*.pdf) High Compression PDF (*.pdf) Secure PDF (*.pdf) Searchable PDF (*.pdf) XML Paper Specification (*.xps) For OCR 3 HTML (*.htm) Excel (*.xls) Rich Text Format (*.rtf) Word Perfect (*.wpd) Text (*.
ControlCenter4 You can also configure advanced settings by clicking the Advanced Settings button in the scan settings dialog box. 3 Remove Background Colour Removes the base colour of documents to make the scanned data more recognisable. When you use this function, you can select the level from 3 settings: high, medium, and low. Skip Blank Page (For MFC-J4710DW) Removes blank pages of the document from the scanning results.
ControlCenter4 c Click d Confirm and edit (if necessary) the scanned image in the image viewer. e Click (Scan). (Print). 3 f Configure the print settings and then click (Start Printing). Opening the scanned image in an application The 3 (Open with an Application) button lets you scan an image directly into your graphics application for image editing. a b Select the Scan tab. c Click d Confirm and edit (if necessary) the scanned image in the image viewer.
ControlCenter4 g Your default E-mail application will open and the image will be attached to a new E-mail. NOTE The Send E-mail feature does not support Webmail services. Using the OCR feature The 3 (OCR) button lets you scan a document and convert it into text. This text can be edited using a word processing application of your choice. a b Select the Scan tab. c Click d Confirm and edit (if necessary) the scanned image in the image viewer.
ControlCenter4 PC-FAX tab (For MFC models) 3 This section briefly introduces the PC-FAX tab function. For more details of each function, click (Help). NOTE The PC-FAX software can only send monochrome fax documents.
ControlCenter4 Sending an image file from your computer 3 The Send Image File button lets you send an image file as a fax from the computer using the Brother PC-FAX software. a b c Select the PC-FAX tab. d Click e The PC-FAX sending dialog box will appear. Enter a fax number and then click Start. 3 Click Send Image File. Click on the folder tree to browse for the folder where the image you want to send is located. Then select the file you want to send. (Send).
ControlCenter4 c The PC-FAX receiving function is activated and starts to receive fax data from your machine. The received data will appear. To view the data, click d (View). If you want to print the received data, select the data and then click (Print). 3 e Configure the print settings and then click (Start Printing).
ControlCenter4 Device Settings tab 3 This section briefly introduces the Device Settings tab function. For more details of each function, click (Help). 3 1 2 3 4 1 Remote Setup button (For MFC models) 2 Address Book button (For MFC models) 3 Device Scan Settings button 4 BRAdmin button Configuring Remote Setup (For MFC models) 3 The Remote Setup button lets you open the Remote Setup program window to configure most machine and network setting menus. a b c Select the Device Settings tab.
ControlCenter4 Configuring the Scan button settings 3 The Device Scan Settings button lets you configure your machine’s Scan button settings. NOTE You can change the Scan button settings using your Brother machine - however, these changes are only temporary. 3 If you want to make permanent changes, click Device Scan Settings and configure as required. There are four scan functions which you can configure to fit your scanning needs.
ControlCenter4 NOTE • Secure PDF is also available for Scan to E-mail and Scan to File. • You can change the data compression ratio of the scanned image with File size. OCR tab 3 3 Lets you configure settings for Scan to OCR by pressing the Scan button on your Brother machine. Choose the settings for File Type, Target Application, OCR Language, Destination File Path, Resolution, Scan Type, Document Size, Brightness, Contrast and Advanced Settings as needed. Click OK.
ControlCenter4 NOTE If you have installed both BRAdmin Light and BRAdmin Professional, ControlCenter4 will launch BRAdmin Professional 3.
ControlCenter4 Support tab This section briefly introduces the Support tab function. For more details of each function, click 3 (Help). Opening ControlCenter Help 3 3 The ControlCenter Help lets you open the Help file for more detailed information about ControlCenter. a b c Select the Support tab. Click ControlCenter Help. The ControlCenter Help main page will appear.
ControlCenter4 Using ControlCenter4 in Advanced Mode 3 This section briefly introduces the ControlCenter4 function in Advanced Mode. For more details of each function, click (Help). 1 2 3 4 5 6 7 8 9 10 3 11 1 Scan directly to a file, E-mail, word processor or graphics application of your choice. 2 Access the PC-Copy feature available via your computer.
ControlCenter4 ControlCenter4 Features for Advanced Mode users 3 Scan (See Scan tab on page 81.) See File types on page 82. See Document Size on page 82. See Advanced Settings on page 82. 3 See Opening the scanned image in an application on page 82. See Using the OCR feature on page 82. See Attaching the scanned data to E-mail on page 82. See Saving the scanned image on page 83. See How to change the default settings of each button on page 83. PC-Copy (See PC-Copy tab on page 84.
ControlCenter4 Scan tab 3 There are four scan options: Image, OCR, E-mail and File. This section briefly introduces the Scan tab function. For more details of each function, click 1 2 3 4 (Help).
ControlCenter4 File types 3 You can choose a file type to save the scanned images as. For details, see File types on page 67. Document Size 3 3 You can choose the document size from the Document Size drop-down list. If you choose a 1 to 2 document size, such as 1 to 2 (A4), the scanned image will be divided into two A5 size documents. Advanced Settings 3 You can configure advanced settings. For details, see Advanced Settings on page 67.
ControlCenter4 a Select the Scan tab. b Click c You can configure the scan settings in this dialog box. If you want to preview and configure the scanned image, check PreScan box. d Click Scan. Your default E-mail application will open and the image will be attached to a new E-mail. (E-mail). The Scan Settings dialog box appears. 3 NOTE The E-mail feature does not support Webmail services.
ControlCenter4 PC-Copy tab 3 Printing the scanned image 3 You can scan a page on the machine and print copies using any of the features of the ControlCenter4 supported Brother machine’s printer driver. a b Select the PC-Copy tab. c d Click Colour Copy, Monochrome Copy, 2 in 1 Copy or 4 in 1 Copy. 3 If you want to change the scan settings, right-click the button you want to change and then change the settings. If you want to preview and configure the scanned image, check PreScan box. Click OK.
ControlCenter4 Photo tab 3 There are four functions: Photo Print, Open PCC Folder, Copy from PCC and Copy to Application. This section briefly introduces the functions. For more details of each function, click 1 2 3 (Help). 4 3 1 Photo Print button 2 Open PCC Folder button 3 Copy from PCC button 4 Copy to Application button Printing/Editing images The 3 (Photo Print) button lets you print or edit images.
ControlCenter4 f Click OK. g Click (Start Printing). Editing images 3 3 a Click b Choose images you want to edit by clicking the image from the image viewer, check the check box under the image, and then enter the number of copies you want to print (1 to 99). c Click d Edit the images with Trimming, Image Correction and Image Enhancement functions. e Click (Photo Print). The image viewer will appear. (Edit). The Photo Print window will appear. (Save).
ControlCenter4 PC-FAX tab (For MFC models) This section briefly introduces the PC-FAX tab function. For more details of each function, click 3 (Help). NOTE The PC-FAX software can only send monochrome fax documents. 3 Sending an image file from your computer 3 The (Send Image File) button lets you send an image file as a fax from the PC using the Brother PC-FAX software. a Select the PC-FAX tab.
ControlCenter4 NOTE Before you use the PC-FAX Receive function, you must select the PC-FAX Receive option from the control panel menu of your Brother machine. (See Enabling the PC-FAX Receiving software on your machine on page 109.) a Select the PC-FAX tab. b Click c The PC-FAX receiving function activates and starts to receive fax data from your machine. The received 3 (View Received PC-FAX). data will appear. To view the data, click (View).
ControlCenter4 Device Settings tab 3 This section briefly introduces the Device Settings tab function. For more details of each function, click (Help). Configuring Remote Setup (For MFC models) 3 The (Remote Setup) button lets you open the Remote Setup program window to configure most machine and network setting menus. a Select the Device Settings tab. b Click c For Remote Setup configuration, see Remote Setup (For MFC models) on page 96. (Remote Setup).
ControlCenter4 Configuring Scan button settings The 3 (Device Scan Settings) button lets you configure your machine’s Scan button settings. NOTE You can change the Scan button settings using your Brother machine - however, these changes are only temporary. 3 If you want to make permanent changes, click Device Scan Settings and configure as required. There are four scan functions which you can configure to fit your scanning needs.
ControlCenter4 If you choose Secure PDF from the File Type drop-down list, click the (Set PDF Password) button. The Set PDF Password dialog box will appear. Enter your password in the Password and Re-type Password box and then click OK. NOTE • Secure PDF is also available for Scan to E-mail and Scan to File. 3 • You can change the data compression ratio of the scanned image with File size. OCR tab 3 Lets you configure settings for Scan to OCR by pressing the Scan button on your Brother machine.
ControlCenter4 a Select the Device Settings tab. b Click (BRAdmin). The BRAdmin Light or BRAdmin Professional 3 utility dialog box appears. NOTE If you have installed both BRAdmin Light and BRAdmin Professional, ControlCenter4 will launch BRAdmin Professional 3.
ControlCenter4 Support tab This section briefly introduces the Support tab function. For more details of each function, click 3 (Help). Opening ControlCenter Help 3 3 The (ControlCenter Help) button lets you open the Help file for detailed information about ControlCenter. a Select the Support tab. b Click c The ControlCenter Help top page will appear. (ControlCenter Help).
ControlCenter4 Custom tab This section briefly introduces adding Custom tabs. For more details, click 3 (Help). Creating a Custom tab 3 3 You can create up to three customized tabs including up to five customized buttons with your preferred settings. a Click Configuration and then select Create custom tab. Creating a Custom button 3 a Click Configuration and then select Create custom button. Select a button you want to create from the menu. The settings dialog box will appear.
ControlCenter4 3 NOTE You can change or remove the created tab, button or settings. Click Configuration and follow the menu.
4 Remote Setup (For MFC models) 4 Remote Setup 4 The Remote Setup program lets you configure many machine settings from a Windows® application. When you start this application, the settings on your machine will be downloaded automatically to your computer and displayed on your screen. If you change the settings, you can upload them directly to the machine. Click the button, All Programs, Brother, MFC-XXXX, and Remote Setup.
Remote Setup (For MFC models) Import Lets you read the settings from a file. NOTE • You can use the Export button to save all your settings for your machine. • If your computer is protected by a firewall, and is unable to use Remote Setup, you may need to configure the firewall settings to allow communication through port number 137. For more information, see Firewall settings (For Network users) on page 116.
5 Brother PC-FAX Software (For MFC models) 5 PC-FAX sending 5 The Brother PC-FAX feature lets you use your computer to send a document file from an application as a standard fax. You can even attach a cover page. All you have to do is set up the receiving parties as members or groups in your PC-FAX Address Book or simply enter the destination address or fax number into the user interface. You can use the Address Book Search feature to quickly find members to send to.
Brother PC-FAX Software (For MFC models) c Choose Brother PC-FAX as your printer, and then click Print. The PC-FAX sending dialog box appears: d Enter a fax number using any of the following methods: 5 Use the dial pad to enter the number. NOTE If you check the Dial Restriction check box, a confirmation dialog box will appear for you to re-enter the fax number using the dial pad. This feature helps to prevent transmissions to the wrong destination.
Brother PC-FAX Software (For MFC models) 5 b c Enter this information to create the fax header and cover page. Click OK to save the User Information. NOTE You can set up the User Information separately for each Windows® account. Sending setup 5 From the Brother PC-FAX Setup dialog box, choose the Sending tab to display the screen below. Outside line access Enter the characters (including numbers and !, #, *, - and +) used to access an outside line here.
Brother PC-FAX Software (For MFC models) Setting up a cover page From the PC-FAX dialog box, click the 5 icon to access the Brother PC-FAX Cover Page Setup screen. The Brother PC-FAX Cover Page Setup dialog box appears: 5 Entering cover page information 5 NOTE If you are sending a fax to more than one recipient, the recipient information will not be printed on the cover page. To Choose the recipient information you want to add to the cover page.
Brother PC-FAX Software (For MFC models) Address Book 5 If Outlook, Outlook Express or Windows Mail is installed on your computer, you can choose in the Select Address Book drop-down list which address book to use for PC-FAX sending. There are five types: Brother Address Book, Outlook, Outlook Express, Windows Mail Address or Windows Contacts. For the address book file, you must enter the path and file name of the database file which contains the address book information.
Brother PC-FAX Software (For MFC models) Brother Address Book a Click the 5 button, All Programs, Brother, MFC-XXXX (where XXXX is your model name), PC-FAX Sending, then PC-FAX Address Book. The Address Book dialog box appears: 5 Setting up a member in the Address Book 5 In the Address Book dialog box you can add, edit and delete members and groups. a In the Address Book dialog box, click the icon to add a member.
Brother PC-FAX Software (For MFC models) Setting up a group for broadcasting 5 You can create a group to send the same PC-FAX to several recipients at one time. a In the Address Book dialog box, click the icon to create a Group. The Address Book Group Setup dialog box appears: 5 b c Enter the name of the new group in the Group Name field. d After all the members you want have been added, click OK. In the Available Names box, choose each member to be included in the group, and then click Add >>.
Brother PC-FAX Software (For MFC models) b Click the delete c When the confirmation dialog box appears, click OK. icon. Exporting the Address Book 5 You can export the whole Address Book to an ASCII text file (*.csv). You can also create a vCard for an address book member that can be attached to an outgoing E-mail (a vCard is an electronic business card that contains the sender’s contact information).
Brother PC-FAX Software (For MFC models) d Click OK to save the data. 5 e Enter the file name, and then click Save. Importing to the Address Book 5 You can import ASCII text files (*.csv), vCards (electronic business cards) or Remote Setup Dial Data into your Address Book. a Do one of the following: From the Address Book, click File, Import, then Text. From the Address Book, click File, Import, then vCard and go to e.
Brother PC-FAX Software (For MFC models) b From the Available Items column choose the data fields you want to import, and click Add >>. NOTE From the Available Items list choose the fields in the same order they are listed in the import text file. c d e Choose Tab or Comma based on the file format you are importing from Divide Character. Click OK to import the data. Enter the file name, and then click Open. 5 NOTE If you chose Text in a, Files of type: will be Text files {*.txt;*.csv}.
Brother PC-FAX Software (For MFC models) PC-FAX receiving 5 The Brother PC-FAX Receive software lets you view and store faxes on your computer. It is automatically installed when you install the MFL-Pro Suite and works on locally or network connected machines. When enabled, your machine will receive faxes in its memory. Once it has received the fax, it will automatically be sent to your computer. If you turn your computer off, your machine will continue to receive and store your faxes in its memory.
Brother PC-FAX Software (For MFC models) • (For MFC-J4710DW) If you receive a fax containing multiple paper sizes (for example, a page of Letter/A4 data and a page of Ledger/A3 data), the machine creates a new file each time it receives a different paper size. When your computer is turned off, the machine stores the files in its memory. The LCD will show that more than one fax job has been received.
Brother PC-FAX Software (For MFC models) c Press s or t to display Setup Receive. Press Setup Receive. d Press s or t to display Memory Receive. Press Memory Receive. e Press s or t to display PC Fax Receive. Press PC Fax Receive. Press OK. f g Press s or t to choose or your computer name if connected to a network. h Press Press Backup Print:On or Backup Print:Off. 5 .
Brother PC-FAX Software (For MFC models) 5 b c d In Save file to, click Browse if you want to change the path where PC-FAX files are saved. e To automatically start the PC-FAX receiving software when you start Windows ®, check Add to Startup folder. f If you want to use the PC-FAX Receiving software over your network, see Configuring the Network PC-FAX Receiving Settings on page 112. In File Format, choose .tif or .pdf as the received document format. The default format is .tif.
Brother PC-FAX Software (For MFC models) Configuring the Network PC-FAX Receiving Settings 5 The settings to send received faxes to your computer were automatically configured during the installation of MFL-Pro Suite. See Quick Setup Guide. If you are using a different machine than the one that was registered to your computer during the installation of the MFL-Pro Suite software, follow the steps below. a In the PC-Fax Rx Setup dialog box, click Network Settings.
Brother PC-FAX Software (For MFC models) You can specify the computer name that will appear on the display of the machine. To change the name, enter the new name in Display Your PC Name. Viewing new PC-FAX messages 5 Each time your computer is receiving a PC-FAX, the icon will alternate between and has been received, the icon will change to once the received fax . The icon will change to . Once the fax has been viewed. a Double-click b c Open the Fax Received folder.
6 PhotoCapture Center™ 6 IMPORTANT DO NOT start your computer with a memory card or USB Flash memory drive installed in the media drive of the machine. You could lose your data or damage the media. NOTE • The PhotoCapture Center™ will read only the media that was put in first. • While the machine is printing from the PhotoCapture Center™, your computer cannot access the PhotoCapture Center™ for any other operation. Using PhotoCapture Center™ a b c 6 Open the media slot cover.
PhotoCapture Center™ For Network Users a b c Open the media slot cover. d Click the name of the file you want to see. 6 Put a memory card or USB Flash memory drive into your machine. Start a web browser which supports the FTP protocol. Your browser software accesses the media using the FTP protocol and the network Host Name of the machine. You can also access the media by entering ftp://XXX.XXX.XXX.XXX (where XXX.XXX.XXX.XXX is the IP address of your Brother machine) from your web browser.
7 Firewall settings (For Network users) 7 Before using the Brother software 7 Firewall settings on your computer may reject the necessary network connection for network printing, network scanning and PC-Fax. If you are using Windows® Firewall and you installed MFL-Pro Suite from the CD-ROM, the necessary Firewall settings have already been made. If you did not install from the CD-ROM follow the instructions below to configure Windows® Firewall.
Firewall settings (For Network users) 2 In Name or IP address (for example 192.168.0.12) of the computer hosting this service on your network: Enter “Localhost”. 3 In External Port number for this service: Enter “54925”. 4 In Internal Port number for this service: Enter “54925”. 5 Make sure UDP is selected. 6 Click OK. 1 2 3 5 7 4 e f Click Add. Add port 54926 for Network PC-Fax by entering the information below: 1 In Description of service: Enter any description, for example “Brother PC-Fax”.
Firewall settings (For Network users) 5 Make sure UDP is selected. 6 Click OK. i Make sure that the new setting is added and is checked, and then click OK. Windows Vista® users a Click the 7 button, Control Panel, Network and Internet, Windows Firewall and click Change settings. b When the User Account Control screen appears, do the following: Users who have administrator rights: Click Continue. 7 For users who do not have administrator rights: Enter the administrator password and click OK.
Firewall settings (For Network users) d Choose the Exceptions tab. e f Click Add port. 7 To add port 54925 for network scanning, enter the information below: 1 In Name: Enter any description, for example “Brother Scanner”. 2 In Port number: Enter “54925”. 3 Make sure UDP is selected. Then, click OK. 1 2 3 g h Click Add port. To add port 54926 for Network PC-Fax, enter the information below: 1 In Name: Enter any description, for example “Brother PC-Fax”. 2 In Port number: Enter “54926”.
Firewall settings (For Network users) j If you still have trouble with your network connection such as Network Scanning or Printing, check the File and Printer Sharing box in the Exceptions tab and then click OK. 7 Windows® 7 users a Click the 7 button, Control Panel, System and Security and then Windows Firewall. Make sure the Windows Firewall state is set to On. b c Click Advanced settings. The Windows Firewall with Advanced Security window appears. Click Inbound Rules.
Firewall settings (For Network users) d Click New Rule. 7 e f Choose Port and click Next. To add port enter the information below: For network scanning Choose UDP and enter “54925” in the Specific local ports. Click Next. For Network PC-Fax Choose UDP and enter “54926” in the Specific local ports. Click Next.
Firewall settings (For Network users) g h i Choose Allow the connection and click Next. Check the applicable items and click Next. Enter any description in Name: (for example “Brother Scanner” or “Brother PC-Fax”) and click Finish. 7 j k Make sure that the new setting is added and is checked. Click Outbound Rules.
Firewall settings (For Network users) l Click New Rule. 7 m n Choose Port and click Next. To add port enter the information below: For network scanning Choose UDP and enter “54925” in the Specific remote ports. Click Next. For Network PC-Fax Choose UDP and enter “54926” in the Specific remote ports. Click Next.
Firewall settings (For Network users) 7 o p q Choose Allow the connection and click Next. r Make sure that the new setting is added and is checked. Check the applicable items and click Next. Enter any description in Name: (for example “Brother Scanner” or “Brother PC-Fax”) and click Finish.
Section II Apple Macintosh Printing and Faxing Scanning ControlCenter2 Remote Setup & PhotoCapture Center™ II 126 145 160 182
8 Printing and Faxing 8 Setting up your computer 8 NOTE The screens shown in this section are mainly from Mac OS X v10.7.x. Screens on your computer may vary depending on your operating system and application. Choosing the right type of paper 8 For high quality printing, it is important to choose the right type of paper.
Printing and Faxing Status Monitor 8 The Status Monitor utility is a configurable software tool for monitoring the status of the machine. It allows you to see error messages such as paper empty, paper jam or ink replacement. Before you can use the tool you must choose your machine in the Model pop-up menu in ControlCenter2. You can check the device status by launching Brother Status Monitor. (Mac OS X v10.5.8) a b Run the System Preferences, select Print & Fax, then choose the machine.
Printing and Faxing Error Messages The ink level is low. The ink cartridge is empty. There is a problem with the ink cartridge. You can set at what interval the software will update the machine status information. Go to the menu bar, Brother Status Monitor and choose Preferences. Hiding or showing the window After starting the Status Monitor, you can hide or show the window. To hide the window, go to the menu bar, Brother Status Monitor and choose Hide Status Monitor.
Printing and Faxing Using the Brother printer driver 8 Choosing page setup options a 8 From an application such as Apple TextEdit, click File, then Page Setup. Make sure Brother MFC-XXXX (where XXXX is your model name) is chosen in the Format For pop-up menu. You can change the settings for Paper Size, Orientation and Scale, then click OK. 8 NOTE • The printer driver does not support Watermark printing. • You can print using A3, Legal and Ledger paper only from the manual feed slot.
Printing and Faxing NOTE You can save the current settings as a preset by choosing Save As from the Presets pop-up menu. 8 (Mac OS X v10.7.x) For more page setup options, click Show Details.
Printing and Faxing NOTE You can save the current settings as a preset by choosing Save Current Settings as Preset from the Presets pop-up menu. To do borderless printing 8 8 From the Paper Size pop-up menu, choose the size of paper you want to print such as A4 Borderless or A3 Borderless.
Printing and Faxing 2-sided Printing a b 8 Select Layout. Choose Long-Edge binding or Short-Edge binding in Two-Sided. 8 NOTE • The Borderless feature is not available for 2-sided printing. • You cannot use A3, Legal or Ledger paper for 2-sided printing.
Printing and Faxing Choosing printing options 8 To use special printing features, choose Print Settings or Color Settings in the Print dialog box.
Printing and Faxing Print Settings 8 You can choose the Media Type, Slow Drying Paper, Print Quality and Color/Greyscale settings. (For MFC-J4610DW/J4710DW) You can also choose the Paper Source setting. NOTE 8 Check Slow Drying Paper when printing with plain paper on which ink dries slowly. This setting may cause some slight blurring of text. Media Type 8 To achieve the best print results, the media being printed on should be selected in the driver.
Printing and Faxing Print Quality 8 The quality selection lets you choose the print resolution you want for your document. Print quality and speed are related. The higher the quality, the longer it will take to print the document. The quality selections that are available will vary depending on the media type you choose. Fast The fastest print mode and the lowest amount of ink used. Use for printing large volume documents or documents for proofing. Normal Good print quality with typical print speed.
Printing and Faxing • When you are feeding A3, Legal or Ledger size paper in the manual feed slot, the machine holds the printed page after printing so that the page does not fall. Once printing is complete, pull out the printed page and press OK. • (For MFC-J4710DW) You can also print using A3, Legal and Ledger paper from Tray2. Layout 8 To choose Reverse Page Orientation or Flip horizontally, select Layout.
Printing and Faxing • Mirror Print is not available when choosing Transparencies as the Media Type. Advanced settings 8 8 Click Advanced to configure Change Data Transfer Mode, Advanced 2-sided Settings and Other Print Options settings. Change Data Transfer Mode 8 The Change Data Transfer Mode feature lets you choose print data transfer mode to improve print quality or print speed. Recommended Setting Choose Recommended Setting for general use.
Printing and Faxing Improved Print Speed Choose Improved Print Speed for faster print speed. Advanced 2-sided Settings 8 Some types of print media may need more drying time when using the 2-sided feature. Change Advanced 2-sided Settings if you have problems with smudged 2-sided prints or paper jams. Normal Choose Normal to print at a typical speed, using a normal amount of ink. 2-sided 1 (Slower print speed) Choose 2-sided 1 to print at a slower speed, using a normal amount of ink.
Printing and Faxing Color Settings 8 Colour is adjusted to get the closest colour match with the monitor. Natural: Use for photographic images. The colour is adjusted to print more natural colours. Vivid: Use for business graphics such as charts, graphics and text. The colour is adjusted to print more vivid colours. None ColorSync: This option is shown and used automatically when choosing ColorSync in Color Matching.
Printing and Faxing Contrast Adjusts the contrast of an image. Increase the contrast when you want an image to be clearer. Decrease the contrast when you want an image to be more subdued. Red Increases the intensity of Red in the image. Green Increases the intensity of Green in the image. Blue Increases the intensity of Blue in the image. Halftone Pattern 8 The machine can use two methods (Diffusion or Dither) to arrange dots to express halftones.
Printing and Faxing Sending a fax (For MFC models) 8 You can send a fax directly from an application. a b Create a document in an application. From an application such as Apple TextEdit, click File, then Print. (Mac OS X v10.5.8 to 10.6.x) Click the disclosure triangle beside the Printer pop-up menu. 8 (For Mac OS X v10.7.x) For more page setup options, click Show Details.
Printing and Faxing 8 142
Printing and Faxing c Choose Send Fax from the pop-up menu. d Choose Facsimile from the Output pop-up menu. e Enter a fax number in the Input Fax Number box, and then click Print to send the fax. 8 NOTE • If you check the Dial Restriction check box, a confirmation box will appear for you to re-enter the fax number. Therefore, this feature helps to prevent transmissions to the wrong destination.
Printing and Faxing • If you want to send a fax to more than one number, click Add after entering the first fax number. The destination fax numbers will be listed in the Destination Fax Numbers field.
9 Scanning 9 Scanning a document using the TWAIN driver 9 The Brother machine software includes a TWAIN Scanner driver for Macintosh. You can use this TWAIN Scanner driver with any applications that support TWAIN specifications. When you scan a document, you can either use the ADF (automatic document feeder) or the scanner glass. Refer to the guide noted below for more information on loading the documents. See Basic User’s Guide: Using the ADF. See Basic User’s Guide: Using the scanner glass.
Scanning Scanning an image into your computer 9 You can scan a whole page, or a portion by pre-scanning the document. Scanning a whole page a b 9 Load your document. Adjust the following settings, if needed, in the scanner setup dialog box: Resolution Scan Type Scanning Area Document Size Adjust Image • Brightness • Contrast c Click Start. When scanning has finished, the image appears in your graphics application.
Scanning c Drag the mouse pointer over the portion you want to scan (1). 1 d Load your document again. NOTE Skip this step if you loaded the document on the scanner glass in step a. 9 e Adjust the settings for Resolution, Scan Type, Brightness and Contrast in the Scanner Setup dialog box as needed. f Click Start. This time only the chosen area of the document appears in the application window. g You can refine the image in your editing software.
Scanning b Check 2-sided Scanning and choose Long-edge binding or Short-edge binding. c Adjust the following settings, if needed, in the scanner setup dialog box: Resolution Scan Type Document Size 9 Adjust Image • Brightness • Contrast d Click Start. NOTE • You cannot adjust the scanning area. • 2-sided scan is available from the ADF only.
Scanning Settings in the Scanner window 9 Resolution 9 You can change the scanning resolution from the Resolution pop-up menu. Higher resolutions take more memory and transfer time, but produce a finer scanned image. The following table shows the resolutions you can choose and the available colours.
Scanning Document Size 9 Choose one of the following sizes: Auto You can scan a standard sized document without any further adjustments to Document Size. A4 210 x 297 mm JIS B5 182 x 257 mm Letter 215.9 x 279.4 mm Legal 215.9 x 355.6 mm (Available on ADF models) A5 148 x 210 mm JIS B6 128 x 182 mm A6 105 x 148 mm Executive 184.1 x 266.
Scanning If the scanned image is too light, set a lower Brightness level and scan the document again. If the image is too dark, set a higher Brightness level and scan the document again. NOTE The Brightness setting is only available when setting the Scan Type to Black & White, Gray (Error Diffusion), True Gray or 24bit Color. 9 Contrast You can increase or decrease the contrast level by moving the slider to the right or left.
Scanning Scanning a document using the ICA driver (Mac OS X v10.6.x, 10.7.x) 9 You can scan a document using the ICA driver. If you installed MFL-Pro Suite from the installer CD-ROM, the ICA driver has been already installed on your Macintosh. You can also scan directly using the Image Capture application. NOTE The screens in this section are from Mac OS X v10.7.x. The screens on your Macintosh may vary depending on your operating system version.
Scanning d Place your document in the ADF or on the scanner glass. If you place the document in the ADF, select Document Feeder for Mode and the size of your document for Scan Size. 9 If you place the document on the scanner glass, select Flatbed for Mode. NOTE • If your Brother machine does not have an ADF, the Mode option does not appear.
Scanning • (For Mac OS X v10.6.x) When the Detect Separate Items box is unchecked, the document will be scanned as one item and saved as one file. When the Detect Separate Items box is checked, the program will detect each image and save them as separate files. If the program does not automatically crop the document as you want, you can do it manually by dragging the mouse cursor over the portion you want to scan from the dialog box that can be accessed by clicking on Show Details. • (For Mac OS X v10.7.
Scanning Combine into single document (Mac OS X v10.7.x): When you choose PDF or TIFF for the file format, check this box to scan a document as one item and save as one file. Image Correction: From the manual setting you can adjust Brightness, Contrast (Mac OS X v10.7.x only), Tint, Temperature, Threshold and Saturation. f Click on Scan to start scanning. Choosing your machine from Print & Fax or Print & Scan 9 a Connect your Brother machine to the computer using a USB cable.
Scanning e Click on the Scanner icon. 9 f Go to step d of Scanning a document using the ICA driver (Mac OS X v10.6.x, 10.7.x) on page 152 to continue. The screens vary depending on the scanning methods you are using.
Scanning Using Presto! PageManager 9 Presto! PageManager is an application for managing the documents in your computer. Since it is compatible with most image editors and word processing programs, Presto! PageManager gives you unmatched control over your files. You can easily manage your documents, edit your E-mail and files and read documents with the OCR software built into Presto! PageManager. If you use the machine as a scanner, we recommend that you install Presto! PageManager.
Scanning Technical support 9 For USA Company name: NewSoft America Inc. Postal Address: 47102 Mission Falls Court, Suite 202 Fremont CA 94539 Telephone: 510-770-8900 Fax: 510-770-8980 E-mail Address: contactus@newsoftinc.com URL: http://www.newsoftinc.com/ For Canada E-mail Address: contactus@newsoftinc.com Germany Company name: SoftBay GmbH Postal Address: Carlstraße 50, D-52531, Übach-Palenberg, Germany Telephone: 0900 1 409640 E-mail Address: de.nsc@newsoft.eu.
Scanning Italy Company name: 5CA Telephone: 0899399878 E-mail Address: it.nsc@newsoft.eu.com URL: http://it.newsoft.eu.com/ Spain Company name: 5CA Telephone: 0807505598 E-mail Address: sp.nsc@newsoft.eu.com Other countries E-mail Address: tech@newsoft.eu.
10 ControlCenter2 10 NOTE • The screens shown in this section are mainly from Mac OS X v10.7.x. Screens on your computer may vary depending on your operating system and application. • The features available to you in ControlCenter2 may vary depending on the model number of your machine. Using ControlCenter2 10 ControlCenter2 is a software utility that lets you quickly and easily access your often used applications. Using ControlCenter2 eliminates the need to manually launch specific applications.
ControlCenter2 b c Uncheck Start ControlCenter on computer startup. Click OK to close the window. NOTE The ControlCenter2 application icon is in Macintosh HD/Applications/Brother.
ControlCenter2 SCAN 10 There are four scan buttons for the Scan to Image, Scan to OCR, Scan to E-mail and Scan to File features. Image (Default: Apple Preview) Lets you scan a page directly into any graphic viewer/editor application. You can choose the destination application, such as Adobe® Photoshop® or any kind of image editing application on your computer.
ControlCenter2 File types 10 Choose the type of file to save the scanned images as from the pop-up menu. For Image, E-mail and File 10 Windows® Bitmap (*.bmp) JPEG (*.jpg) TIFF (*.tif) TIFF Multi-Page (*.tif) Portable Network Graphics (*.png) PDF (*.pdf) High Compression PDF (*.pdf) Secure PDF (*.pdf) Searchable PDF (*.pdf) For OCR 10 Searchable PDF (*.pdf) Text (*.txt) Rich Text Format (*.rtf) HTML (*.htm) 10 Excel 97 (*.
ControlCenter2 Remove Background Colour Removes the base colour of documents to make the scanned data more recognisable. When you use this function, you can select the level from 3 settings: high, medium, and low. Skip Blank Page (For MFC-J4710DW) Removes blank pages of the document from the scanning results. Display Scanning Results (For MFC-J4710DW) Shows the numbers of total pages saved and blank pages skipped on your computer screen.
ControlCenter2 c You can configure the scan settings. To scan and then crop a portion of a page after pre-scanning the document, check the Show Scanner Interface check box. (For MFC-J4710DW) To scan a 2-sided document, check the 2-sided Scanning check box and choose Long-edge binding or Short-edge binding. To change the application that you want to use, choose the appropriate application from the Target Application pop-up menu. You can add an application to the list by clicking Add.
ControlCenter2 OCR (word processing application) 10 The Scan to OCR feature lets you convert the graphic page image data into text which can be edited by any word processing application. You can change the default word processing application. a Select the SCAN tab. b Click (OCR). The Scan to OCR dialog box will appear. 10 c You can configure the scan settings. To scan and then crop a portion of a page after pre-scanning the document, check the Show Scanner Interface check box.
ControlCenter2 E-mail 10 The Scan to E-mail feature lets you scan a document to your default E-mail application so you can send the scanned document as an attachment. a Select the SCAN tab. b Click (E-mail). The Scan to E-mail dialog box will appear. 10 c You can configure the scan settings. To scan and then crop a portion of a page after pre-scanning the document, check the Show Scanner Interface check box.
ControlCenter2 NOTE The Scan to E-mail feature does not support Webmail services. Use the Scan to Image or Scan to File feature to scan a document or picture, and then attach the file of the scanned data to an E-mail message.
ControlCenter2 File 10 The Scan to File button lets you scan an image to a folder on your hard disk in a supported file format. Therefore, this feature allows you to easily archive your paper documents. a Select the SCAN tab. b Click (File). The Scan to File dialog box will appear. 10 c You can configure the scan settings. To scan and then crop a portion of a page after pre-scanning the document, check the Show Scanner Interface check box.
ControlCenter2 Changing the default settings of a button You can change the default settings of the (Image), 10 (OCR), (E-mail), and (File) buttons. a Click the button while holding down the Ctrl key and choose Software Button. The settings dialog box will appear. b Choose the settings for File Type, Show Scanner Interface, Resolution, Scan Type, Document Size, Brightness, Contrast, and Continuous Scanning as needed. (For MFC-J4710DW) You can also choose the setting for 2-sided Scanning.
ControlCenter2 10 171
ControlCenter2 CUSTOM SCAN 10 There are four buttons which you can configure to fit your scanning needs. To customize a button, click the button while holding down the Ctrl key, and the configuration window appears. There are four scan functions: Scan to Image, Scan to OCR, Scan to E-mail and Scan to File. Scan to Image Lets you scan a page directly into any image viewer/editor software. You can choose any image editor application on your computer as a destination.
ControlCenter2 File types 10 You can choose the file type to save the scanned images. For details, see File types on page 163. Document Size 10 You can choose the document size from the pull-down list. If you choose a 1 to 2 document size, such as 1 to 2 (A4), the scanned image will be divided into two A5 size documents. Advanced Settings 10 You can configure advanced settings. For details, see Advanced Settings on page 163.
ControlCenter2 Scan to Image/OCR/E-mail/File 10 General tab Enter a name in Name for Custom (up to 30 characters) to create the button name. Choose the type of scan from the Scan Action selections. Settings tab (Scan to Image/OCR/ E-mail) 10 Choose the Target Application, File Type, Resolution, Scan Type, Document Size, 2-sided Scanning 1, Show Scanner Interface, Brightness and Contrast settings. 1 (For MFC-J4710DW) NOTE The Scan to E-mail feature does not support Webmail services.
ControlCenter2 If you choose Secure PDF from the File Type list, the Set PDF Password dialog box appears. Enter your password in the Password and Re-type Password box and then click OK. NOTE Secure PDF is available for Scan to Image, Scan to E-mail and Scan to File. Settings tab (Scan to File) Choose the file format from the File Type pop-up menu. Save the file to the default folder or choose your preferred folder by clicking the Browse button.
ControlCenter2 10 176
ControlCenter2 COPY / PC-FAX (PC-FAX for MFC models) (Mac OS X v10.5.8, 10.6.x) 10 COPY - Lets you use your computer and any printer driver for enhanced copy operations. You can scan a page on the machine and print the copies using any of the features of the machine’s printer driver, or you can direct the copy output to any standard printer driver installed on your computer including network printers. PC-FAX - Lets you scan a page or document and automatically send the image as a fax from the computer.
ControlCenter2 To copy, click the Print button. To fax, click the disclosure triangle beside the Printer pop-up menu and then choose Send Fax from the pop-up menu. (See Sending a fax (For MFC models) on page 141.
ControlCenter2 DEVICE SETTINGS 10 You can configure the machine settings or check ink levels by clicking a button. Remote Setup (For MFC models) Lets you open the Remote Setup program. (See Remote Setup (For MFC models) on page 182.) Address Book (For MFC models) Lets you open the Address Book window of the Remote Setup. (See Remote Setup (For MFC models) on page 182.) Ink Level Lets you open the Brother Status Monitor, which displays the ink level for each cartridge.
ControlCenter2 Remote Setup (For MFC models) 10 The Remote Setup button lets you open the Remote Setup program window to configure the machine setting menus. NOTE For details, see Remote Setup (For MFC models) on page 182. 10 Address Book (For MFC models) 10 The Address Book button lets you open the Address Book window in the Remote Setup program, so you can easily register or change the dial numbers from your computer.
ControlCenter2 Ink Level 10 The Ink Level button opens the Status Monitor window, which displays the ink level for each cartridge.
11 Remote Setup & PhotoCapture Center™ 11 Remote Setup (For MFC models) 11 The Remote Setup program lets you configure many machine settings from an application. When you access this application, the settings on your machine will be downloaded automatically to your computer and displayed on your screen. If you change the settings, you can upload them directly to the machine. NOTE The Remote Setup icon is in Macintosh HD/Applications/Brother.
Remote Setup & PhotoCapture Center™ Import Lets you read the settings from a file. NOTE • You can use the Export button to save all your settings for your machine. • If you need to change the machine that was registered to your computer during the installation of MFL-Pro Suite (See Quick Setup Guide.), or if the network environment was changed, you need to specify the new machine. Open the Device Selector and choose the new machine.
Remote Setup & PhotoCapture Center™ PhotoCapture Center™ 11 You can access a memory card or a USB Flash memory drive installed in the machine from a computer. IMPORTANT DO NOT start your computer with a memory card or a USB Flash memory drive installed in the media drive of the machine. You could lose your data or damage the media. NOTE • The PhotoCapture Center™ will read only the media that was put in first.
Remote Setup & PhotoCapture Center™ c Launch any FTP software or any web browser in which FTP is supported. Your browser software accesses the memory card or USB Flash memory drive using the FTP protocol and the network Host Name of the machine. In the address bar, enter ftp://XXX.XXX.XXX.XXX (where XXX.XXX.XXX.XXX is the IP address of your Brother machine). Your browser software appears and a list of file names on your memory card or USB Flash memory drive is shown.
Section III Using the Scan button III USB cable scanning Network Scanning 187 201
12 USB cable scanning 12 Using the Scan button over a USB cable connection 12 NOTE If you use the Scan button on a network, see Network Scanning on page 201. You can use the Scan button on the Touch Panel to scan documents directly into your word processing, graphics or E-mail applications, to a folder on your computer, or to a memory card or USB Flash memory drive. Before you can use the Scan button, you must install the Brother MFL-Pro Suite software and connect the machine to your computer.
USB cable scanning Scan to E-mail 12 You can scan either a monochrome or colour document into your E-mail application as a file attachment. NOTE The Scan to E-mail feature does not support Webmail services. Use the Scan to Image or Scan to File feature to scan a document or picture, and then attach the file of the scanned data to an E-mail message. For MFC-J2510/J4510DW/J4710DW 12 a Load your document. b Press c Swipe left or right to display d Press (to E-mail).
USB cable scanning For DCP-J4110DW, MFC-J2310/J4310DW/J4410DW/J4610DW a b c d 12 Load your document. Press Scan. Press s or t to display Scan to email. Press Scan to email. Do one of the following: If you want to use the default settings, go to i. If you want to change the default settings, go to e. e f Press Options. Press Set with TouchPanel. Press On. NOTE To use Set with TouchPanel, the ControlCenter software must be installed on the computer that is connected to the machine.
USB cable scanning c Swipe left or right to display d Press (to Image). The icon moves to the middle and is highlighted in blue. e Press OK. Do one of the following: (to Image). If you want to use the default settings, go to k. If you want to change the default settings, go to f. f g Press Options. h Press Set with Touch Panel. Press On. (For MFC-J4710DW) If you want to use 2-sided scanning, press 2-sided Scan. Press 2-sided Scan: Long Edge or 2-sided Scan: Short Edge.
USB cable scanning f Press Set with TouchPanel. Press On. NOTE To use Set with TouchPanel, the ControlCenter software must be installed on the computer that is connected to the machine. g Choose the settings for Scan Type, Resolution, File Type and Remove Background as needed. h i Press OK. Press Start. The machine starts scanning the document. NOTE You can change the Scan button settings using your Brother machine - however, these changes are only temporary.
USB cable scanning g (For MFC-J4710DW) If you want to use 2-sided scanning, press 2-sided Scan. Press 2-sided Scan: Long Edge or 2-sided Scan: Short Edge. h Press Set with Touch Panel. Press On. NOTE To use Set with Touch Panel, the ControlCenter software must be installed on the computer that is connected to the machine. i Choose the settings for Skip Blank Page 1, Scan Type, Resolution and File Type as needed. 1 j k (For MFC-J4710DW) Press OK. Press Start.
USB cable scanning NOTE • You can change the Scan button settings using your Brother machine - however, these changes are only temporary. If you want to make permanent changes, use the ControlCenter software. (For Windows®, see Configuring the Scan button settings on page 75 when choosing Home Mode, and see Configuring Scan button settings on page 90 when choosing Advanced Mode. For Macintosh, see Configuring Scan button settings on page 170.
USB cable scanning Press 2-sided Scan: Long Edge or 2-sided Scan: Short Edge. h Press Set with Touch Panel. Press On. NOTE To use Set with Touch Panel, the ControlCenter software must be installed on the computer that is connected to the machine. i Choose the settings for Scan Type, Resolution, File Type, Skip Blank Page 1 and Remove Background Colour as needed. 1 j k (For MFC-J4710DW) Press OK. Press Start. The machine starts scanning the document.
USB cable scanning NOTE You can change the Scan button settings using your Brother machine - however, these changes are only temporary. If you want to make permanent changes, use the ControlCenter software. (For Windows®, see Configuring the Scan button settings on page 75 when choosing Home Mode, and see Configuring Scan button settings on page 90 when choosing Advanced Mode. For Macintosh, see Configuring Scan button settings on page 170.
USB cable scanning Scan to Media 12 You can scan monochrome and colour documents directly to a memory card or USB Flash memory drive. Monochrome documents may be stored in the PDF (*.PDF) or TIFF file formats (*.TIF). Colour documents may be stored in PDF (*.PDF) or JPEG (*.JPG) file formats. File names are based on the current date. For example, the fifth image scanned on 1 July 2012 would be named 01071205.PDF. You can change the colour, quality and file name.
USB cable scanning NOTE The Auto Crop feature is supported by technology from Reallusion, Inc. Guidelines for Auto Crop 12 This setting is only available for documents that are rectangular or square. If your document is too long or wide, this setting does not work correctly. You must place the documents away from the edges of the scanner glass as shown in the illustration. You must place the documents at least 10 mm apart from each other.
USB cable scanning NOTE • If you choose colour in the quality setting, you cannot choose TIFF. • If you choose monochrome in the quality setting, you cannot choose JPEG. g The file name is set automatically. However, you can create a name of your choice using the character buttons on the LCD. Press File Name and then enter the file name. You can only change the first 6 digits of the file name. Press OK. h Press OK. NOTE If you want to save the settings as a shortcut, press Save as Shortcut.
USB cable scanning h Choose the settings for Scan Type, Resolution, File Type, and Remove Background as needed. NOTE • If you choose colour in the quality setting, you cannot choose TIFF. • If you choose monochrome in the quality setting, you cannot choose JPEG. i The file name is set automatically. However, you can create a name of your choice using the character buttons on the LCD. You can only change the first 6 digits of the file name. Press s or t to display File Name. Press File Name.
USB cable scanning c d Press Options. e Press Yes to confirm. f Press Swipe up or down, or press a or b to choose Factory Reset. Press Factory Reset. . Setting the new default (For DCP-J4110DW, MFC-J2310/J4310DW/J4410DW/J4610DW) a Put a memory card or USB Flash memory drive into your machine. The LCD screen automatically changes. Press . b c Press Scan. d Choose the settings for Scan Type, Resolution, File Type and Remove Background as needed. e Press s or t to display Set New Default.
13 Network Scanning 13 To use the machine as a network scanner, the machine must be configured with a TCP/IP address. You can set or change the address settings from the control panel (See Network User’s Guide: Control panel setup.) or by using the BRAdmin Light software. If you installed the machine following the instructions for a network user in the Quick Setup Guide then the machine should already be configured for your network.
Network Scanning Click the button, All Programs, Brother, MFC-XXXX, Scanner Settings, then Scanners and Cameras. b Do one of the following: Windows® XP Right-click the Scanner Device icon and choose Properties. The Network Scanner Properties dialog box appears. Windows Vista® and Windows® 7 Click the Properties button. NOTE (Windows Vista® and Windows ® 7) If the User Account Control screen appears, do the following: • For users who have administrator rights: Click Continue or Yes.
Network Scanning c Click the Network Setting tab and choose the appropriate connection method. Specify your machine by address Enter the IP address of the machine in IP Address, and then click Apply or OK. Specify your machine by name 13 1 Enter the machine node name in Node Name, or click Browse and choose the machine you want to use. 2 Click OK.
Network Scanning d Click the Scan To Button tab and enter your computer name in the Display Name field. The machine’s LCD displays the name you enter. The default setting is your computer name. You can enter any name that you like. e If you want to avoid receiving unwanted documents, enter a 4-digit PIN number in the Pin number and Retype Pin number field.
Network Scanning d Click OK. NOTE • To use the Scan button features on the machine, click the check box for Register your computer with the "Scan To" functions at the machine. Then enter the name you want to be displayed on the machine’s LCD for your computer. You can use up to 15 characters. • You can avoid receiving unwanted documents by setting a 4-digit PIN number. Enter your PIN number in the PIN number and Retype PIN number field.
Network Scanning Using the Scan button on your network 13 NOTE If you are connected using USB, see USB cable scanning on page 187. Scan to E-mail (PC) 13 When you choose Scan to E-mail (PC), your document will be scanned and sent directly to the computer you designated on your network. The ControlCenter software will launch the default E-mail application on the designated computer. You can scan and send a monochrome or colour document from the computer as an E-mail attachment.
Network Scanning i (For MFC-J4710DW) If you want to use 2-sided scanning, press 2-sided Scan. Press 2-sided Scan: Long Edge or 2-sided Scan: Short Edge. j Press Set with Touch Panel. Press On. NOTE To use Set with Touch Panel, the ControlCenter software must be installed on a computer that is connected to the machine. k Choose the settings for Scan Type, Resolution, File Type, Skip Blank Page 1 and Remove Background Colour as needed. 1 l m (For MFC-J4710DW) Press OK. Press Start.
Network Scanning i Choose the settings for Scan Type, Resolution, File Type, and Remove Background as needed. j k Press OK. Press Start. The machine starts scanning the document, creates a file attachment, and launches your E-mail application displaying a new E-mail. NOTE You can change the Scan button settings using your Brother machine - however, these changes are only temporary. If you want to make permanent changes, use the ControlCenter software.
Network Scanning h Do one of the following: If you want to use the default settings, go to l. If you want to change the default settings, go to i. i j Press Options. Choose the settings for 2-sided Scan 1, Scan Type, Resolution and File Type as needed. 1 k (For MFC-J4710DW) Press OK. NOTE If you want to save the settings as a shortcut, press Save as Shortcut. l Press Start. The machine starts scanning the document. For MFC-J2310/J4310DW/J4410DW/J4610DW a b c d e 13 Load your document.
Network Scanning Setting new default settings for Scan to E-mail Server Setting the new default (For MFC-J2510/J4510DW/J4710DW) a b c d Follow the steps form b to g of Scan to E-mail Server (For MFC models) on page 208. e Press Yes to confirm. f Press 13 Press Options. Choose the settings for Scan Type, Resolution and File Type as needed. Swipe up or down, or press a or b to choose Set New Default. Press Set New Default. .
Network Scanning c Press s or t to display Factory Reset. Press Factory Reset. d e Press Yes. Press . Scan to Image 13 When you choose Scan to Image, your document will be scanned and sent directly to the computer you designated on your network. The ControlCenter software will launch the default graphics application on the designated computer. For MFC-J2510/J4510DW/J4710DW a Load your document. b Press c Swipe left or right to display d Press 13 (Scan). (to Image). (to Image).
Network Scanning NOTE To use Set with Touch Panel, the ControlCenter software must be installed on a computer that is connected to the machine. k Choose the settings for Scan Type, Resolution, File Type, Skip Blank Page 1 and Remove Background Colour as needed. 1 l m (For MFC-J4710DW) Press OK. Press Start. The machine starts scanning the document. For DCP-J4110DW, MFC-J2310/J4310DW/J4410DW/J4610DW a b c d e f 13 Load your document. Press Scan. Press s or t to display Scan to Image.
Network Scanning NOTE You can change the Scan button settings using your Brother machine - however, these changes are only temporary. If you want to make permanent changes, use the ControlCenter software. (For Windows®, see Configuring the Scan button settings on page 75 when choosing Home Mode, and see Configuring Scan button settings on page 90 when choosing Advanced Mode. For Macintosh, see Configuring Scan button settings on page 170.
Network Scanning j Press Set with Touch Panel. Press On. NOTE To use Set with Touch Panel, the ControlCenter software must be installed on a computer that is connected to the machine. k Choose the settings for Skip Blank Page 1, Scan Type, Resolution and File Type as needed. 1 l m (For MFC-J4710DW) Press OK. Press Start. The machine starts scanning the document. For DCP-J4110DW, MFC-J2310/J4310DW/J4410DW/J4610DW a b c d e f 13 Load your document. Press Scan. Press s or t to display Scan to OCR.
Network Scanning NOTE • You can change the Scan button settings using your Brother machine - however, these changes are only temporary. If you want to make permanent changes, use the ControlCenter software. (For Windows®, see Configuring the Scan button settings on page 75 when choosing Home Mode, and see Configuring Scan button settings on page 90 when choosing Advanced Mode. For Macintosh, see Configuring Scan button settings on page 170.
Network Scanning NOTE If you want to save the computer as a shortcut, press Save as Shortcut. h i Press Options. j Press Set with Touch Panel. Press On. (For MFC-J4710DW) If you want to use 2-sided scanning, press 2-sided Scan. Press 2-sided Scan: Long Edge or 2-sided Scan: Short Edge. NOTE To use Set with Touch Panel, the ControlCenter software must be installed on a computer that is connected to the machine.
Network Scanning NOTE To use Set with TouchPanel, the ControlCenter software must be installed on a computer that is connected to the machine. i Choose the settings for Scan Type, Resolution, File Type and Remove Background as needed. j k Press OK. Press Start. The machine starts scanning the document. NOTE You can change the Scan button settings using your Brother machine - however, these changes are only temporary. If you want to make permanent changes, use the ControlCenter software.
Network Scanning Scan to FTP 13 When you choose Scan to FTP, you can scan a monochrome or colour document directly to an FTP server on your local network, or on the internet. The details required to use Scan to FTP can be entered by using Web Based Management to pre-configure and store the details in an FTP Profile. NOTE • Scan to FTP is available when FTP profiles are configured by using Web Based Management. • We recommend Microsoft® Internet Explorer® 8.0/9.0 for Windows® and Safari 5.
Network Scanning NOTE Do not use unsuitable characters in the file name (for example ?, /, \, or *). They may cause a sending error when using Scan to FTP. Configuring the FTP Default Settings 13 You can set Passive Mode to Off or On depending on your FTP server and network firewall configuration. By default this setting is On. You can also change the port number used to access the FTP server. The default for this setting is port 21. In most cases these two settings can remain as default.
Network Scanning j Choose the file type for the document from the pop-up menu. You can choose PDF, JPEG or User Select for colour documents, PDF, TIFF or User Select for monochrome documents. k Click Submit. Scan to FTP using FTP Server Profiles 13 For MFC-J2510/J4510DW/J4710DW 13 a Load your document. b Press c Swipe left or right to display d Press (to FTP). The icon moves to the middle and is highlighted in blue. Press OK.
Network Scanning b c d e Press Scan. Press s or t to choose Scan to FTP. Press Scan to FTP. Press s or t to choose one of the FTP server profiles listed. If the Scan to FTP profile is complete, go to f. If the Scan to FTP profile is not complete, the LCD prompts you to enter any missing information. When you finish the settings, go to f. f Press Start. The LCD shows Connecting. When the connection to the FTP server is successful, the machine starts scanning the document.
Network Scanning NOTE Do not use unsuitable characters in the file name (for example ?, /, \, or *). They may cause a sending error when using Scan to Network. Configuring the Scan to Network Default Settings 13 13 a b c Choose Network in Scan to FTP/Network from the Scan tab. Click Submit. Choose the Profile you want to configure in Scan to FTP/Network Profile. Enter the name that you want to use for the Scan to Network profile.
Network Scanning d The Host Address is the domain name of the CIFS server. Enter the Host Address (for example ftp.example.com) (up to 64 characters) or the IP address (for example 192.23.56.189). e Enter the destination folder where your document will be stored on the CIFS server (for example brother\abc) (up to 60 characters). f Choose the file name you want to use for the scanned document. You can choose from seven preset and two user defined file names.
Network Scanning Press OK. e Swipe up or down, or press a or b to choose one of the Network server profiles listed. If the LCD prompts you to enter a PIN number, enter the 4-digit PIN number for the profile on the LCD. Press OK. Do one of the following: If the Scan to Network profile is complete, go to i. If the Scan to Network profile is not complete, the LCD prompts you to enter any missing information. When you finish the settings, go to i.
Network Scanning Using Web Services for scanning on your network (Windows Vista® SP2 or later and Windows® 7) 13 The Web Services protocol enables Windows Vista® (SP2 or later) and Windows ® 7 users to scan using a Brother machine on the network. You must install the driver via Web Services. Refer to the Network User’s Guide noted below for information about installing Web Services.
Network Scanning c Do one of the following: Windows® Photo Gallery Click File, then Import from Camera or Scanner. Windows® Fax and Scan Click File, New, then Scan. d e Choose the scanner you want to use. Do one of the following: Windows® Photo Gallery Click Import. Windows® Fax and Scan Click OK. The Scan dialog box appears.
Network Scanning 8 Brightness 9 Contrast 10 Scanning area 11 Preview 12 Scan g Click Scan on the Scan dialog box. The machine starts scanning the document. NOTE If the LCD shows Out of Memory, decrease the Paper size setting or the Resolution setting. For details, see Configuring settings for scanning on page 228.
Network Scanning g Press Start. The machine starts scanning the document. For DCP-J4110DW, MFC-J2310/J4310DW/J4410DW/J4610DW a b c Load your document. d Press s or t to display the type of scan you want to do. Press the type of scan. e Press s or t to display the computer you want to send to. Press the computer name. f Press Start. The machine starts scanning the document. 13 Press Scan. Press s or t to display Web Service. Press Web Service.
Network Scanning NOTE If you are requested to choose a software application to scan, choose Windows® Fax and Scan or Windows® Photo Gallery from the list.
A Index C R ControlCenter2 Macintosh ............................................................ 160 ControlCenter4 Windows® .............................................................. 60 Remote Setup Macintosh ............................................................. 182 Windows® .............................................................. 96 D Device Selector ...................................... 145, 183, 204 Drivers Macintosh Brother printer driver ......................................
Visit us on the World Wide Web http://www.brother.com/ This product is approved for use in the country of purchase only. Local Brother companies or their dealers will only support machines purchased in their own countries. www.brotherearth.