Wireless Network Setup Guide Cutting Machine Product Code: 891-Z02/Z03/Z04 Be sure to read this document before using the machine. We recommend that you keep this document nearby for future reference.
Trademarks WPA™ and WPA2™ are trademarks of Wi-Fi Alliance®. Compilation and Publication Under the supervision of Brother Industries, Ltd., this manual has been compiled and published, covering the latest product descriptions and specifications. The contents of this manual and the specifications of this product are subject to change without notice.
INTRODUCTION Thank you for purchasing this cutting machine. This guide provides setup instructions so that you can use a wireless network to send data created in ScanNCutCanvas (http://ScanNCutCanvas.Brother.com/) to your cutting machine (hereafter referred to as “machine”) as well as save data that you have edited on your machine to ScanNCutCanvas. Carefully read the instructions in this guide and complete the setup to easily transfer data without the need for any device such as a USB flash drive.
CONTENTS INTRODUCTION ......................................................................................................................... 1 Overview of “ScanNCut Online” for Data Transfer via a Wireless Network ................................ 1 Setting Up the Wireless Network Connection .............................................................................. 3 Activating the Wireless Network ........................................................................................................
Setting Up the Wireless Network Connection The first step of the setup is to connect your machine to a wireless network. If a connection is not established correctly and an error message appears, see “Error codes/Error messages” on page 11. Activating the Wireless Network Setting Up the Wireless Network a A connection to the wireless network can be established using either the wizard (recommended) or an alternative method.
b In the network settings screen, touch beside “Setup Wizard”. d Type in the Network Key (Password) noted in step a, and then touch the “OK” key. f a g b c X Any available SSIDs are searched for and displayed. c d Select the SSID noted in step a, and then touch the “OK” key. a b c d e f Character input display Character keys Uppercase/lowercase selection key Space key Letter/number/special character selection key Backspace key (Deletes the character at the cursor’s position.
Note • If a connection was not successfully established: - If the message “Wrong Network Key: Err-04” appeared, the Network Key (Password) may have been entered incorrectly. Touch the “OK” key, and then repeat the procedure from step b of “Using the Wizard on Your Machine (Recommended)” on page 3. - For details on other causes, see “Error codes/Error messages” on page 11.
Using the “Others” Menu The “Others” menu is on page 2 of the network settings screen. The “Others” menu contains the following items. a b c d a TCP/IP can be manually entered. b Displays the MAC address. c All current network settings will be reset and returned to those when the machine was purchased. After setting this function, turn the machine off, then on again. d Use this when proxy settings are required.
Registering with ScanNCutCanvas for Your Machine After you have registered your machine with ScanNCutCanvas (http://ScanNCutCanvas.Brother.com/), they will be able to communicate via a wireless network connection to transfer data back and forth. If setup is not completed correctly and an error message appears, see “Error codes/Error messages” on page 11. Note • A computer or tablet that is connected to the network and can run ScanNCutCanvas is required.
b Touch the “Next” key. Continue with “Registering Your Machine with ScanNCutCanvas”. Registering Your Machine with ScanNCutCanvas Your ScanNCut machine and your ScanNCutCanvas login ID will be registered together. X The activation code input screen appears. Memo • If this screen does not appear, continue with “Registering Your Machine with ScanNCutCanvas” on page 8. c Using a coin, etc.
c Click screen. in the upper-right corner of the X The page for managing your account appears. d Click the “Get PIN Code” button below “ScanNCut Online”. [MACHINE] f g Touch the “OK” key. In the PIN code input screen on your machine, type the four-digit PIN code that appeared in the ScanNCutCanvas screen , and then touch the “OK” key. X The following screen appears. h Touch e the “OK” key. Type in your machine number, and then click the “Next” button. X Page 7 of the settings screen appears.
Memo Note • A single machine number is linked with a single ScanNCutCanvas login ID. To link a different machine to ScanNCutCanvas, perform the registration operation again with that machine. In that case, the link with the previously registered machine will be cut. • If an error occurs while transferring data, see “Error codes/Error messages” on page 11. • Touch the “Register” key to register your machine with ScanNCutCanvas again.
Troubleshooting Please do not contact Brother Customer Service for assistance without the wireless security information. We cannot assist you in locating your network security settings. How can I find the wireless security information (SSID and Network Key) 1) You should see the documentation provided with your wireless access point/router. 2) The default SSID could be the manufacturer’s name or the model name.
Error code Cause/Solution The Authentication/Encryption methods used by the selected wireless access point/router are not supported by your machine. For infrastructure mode, change the authentication and encryption methods of the wireless access point/router.
Error message Unconnected to the network. Check the network connection status. Cause/Solution The machine is not connected to the network. - Check that there is a good network connection. - A network connection may not yet be established. Wait a while, and then try again.
Please visit us at http://support.brother.com where you can get product support and answers to frequently asked questions (FAQs). These machines are approved for use in the country of purchase only. Local Brother companies or their dealers will only support machines purchased in their own countries.
