BABY TO SLEEP Version: 2.4 Age:14+ Please retain the packaging for future reference since it contains important information.
Table of Content IMPORTANT SAFETY INSTRUCTIONS 4 CAUTION 4 CHOKING 4 POWER ADAPTER PRECAUTIONS 4 WARNING 2 5 FCC INFORMATION FCC ID : ZRB849264 ZRB849264 5 RSS210 INFORMATION 6 BABY TO SLEEP PARTS 1 7 BABY TO SLEEP PARTS 2 8 AC ADAPTOR INSTALLATION 8 15° BASE INSTALLATION 9 WALL MOUNT INSTALLATION 9 SWITCH ON BABY TO SLEEP 10 BABY TO SLEEP DEVICE OPERATION 10 BABY TO SLEEP APP OPERATION 12 PLATFORMS 12 BABY TO SLEEP DIRECT CONNECT 12 BABY TO SLEEP ROUTER CONNECT( (WLAN) )
BABY TO SLEEP APP INTERFACE 14 INFORMATION 19 LED STATUS 19 RESET 20 CARE AND MAINTENANCE 20 SPECIFICATION 20 3
IMPORTANT SAFETY INSTRUCTIONS INSTRUCTIONS All of the safety and operating instructions should be read, adhered to and followed before the unit is operated. AC ADAPTOR : ............. IN:ACV100-240 OUT:DCV5.0 DISTANCE :................... About 25 meter (unobstructed) in DIRECT CONNECT CAMERA : ..................... 320 x 240 @ 25 FRAME / SEC. Wi-Fi : ............................ 802.11b/g/n WARNING Please keep this packaging since it contains important information.
6. 7. 8. RESET Press the RESET button for 5 seconds to reset the device back to factory setting. CARE AND MAINTENANCE Switch off the power of the device and unplug the AC adaptor before cleaning. Apply soft and dry cloth onto the product ONLY. Make sure there is no hair or lint caught between the wheels, the drive shafts and the camera joint. Clean carefully with your fingers or a pair of 9. 10. 11. 12. 13. 14. Do not touch the plug contacts with sharp or metal objects.
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This unit generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
BABY TO SLEEP SLEEP PARTS 1 SETTING Press to enter the SETTING PAGE: 1. CONTINOUS LISTENING 2. CLOSE 3. ROUTER SETUP / DEVICE 1. VOLUME (-) 2. VOLUME (+) 3. NIGHT LIGHT TOGGLE 4. Wi-Fi ON/OFF 5. MUSIC PLAY/STOP 6. SLEEP ENCHANCE 7. SLEEP TIMER 8. BODY 9. MICROPHONE 10. LED NIGHT LIGHT 11. NIGHT VISION 12. CAMERA 13. MUSIC SELECTION 14. TIMER (30 MINUTES) 15. TIMER(60 MINUTES) 16. TIMER (90 MINUTES) 17.
BABY TO SLEEP PARTS 2 Please refer to SLEEP TIMER and SLEEP ENHANCE MODE of this manual for associated instructions. NIGHT LIGHT CONTROL Press to enter the NIGHT LIGHT CONTROL screen: To select between “WHITE LIGHT” and “MULTI-COLOR LIGHT”. 1. AC ADAPTOR HOLE 2. Wi-Fi Indicator 3. SSID 4. RESET 5. Wi-Fi MODE SWITCH 6. AC ADAPTOR 7. 15° BASE 8. WALL MOUNT 1 9.
Device can move around 350° horizontally and 90° vertically. Zoom in and out will be at 25% threshold between 100% to 200%. The zoom ratio will b displayed on the screen. Snapshot picture can be taken by your handheld device. Pictures will be saved at default Picture folder at iOS, and at “/sdcard/P-BabyToSleep/Pictrue” at Android. You can see your babay at the dark by turning on the Night Vision. Video stream will turn to Black and White in Night Vision Mode.
SWITCH ON BABY TO SLEEP There is no power switch for the device. When the AC adaptor is connected, the multi-color LED will turn on, and the device is in service after about 15 seconds, when the LED turns off. The touch panel of the device will be undergoing calibration every time power on and off, and it is recommended not to touch it before the system is ready. 1. SETTING 2. MUSIC CONTROL 3. CAMERA CONTROL 4. NIGHT LIGHT CONTROL 5. VOICE MONITORING 6. VIDEO SCREEN 7.
7. is “White Noise”, if no particular music has been selected. Music List: Exit your APP. The Wi-Fi indicator will change from rapid blinking to slow blinking if connection to the router is made. 8. Womb Turn on the Wi-Fi of your handheld device. Note: You shall not see the SSID of the device (Baby_xxxx) 10. Lullaby Lullaby2 Stream Wood White White lands Rain Stream Ocean Summer Brown White Surf Night Noise Noise Ride Connect to your router’s SSID. 9.
BABY TO SLEEP APP OPERATION baby to sleep APP INSTALLATION BABY TO SLEEP ROUTER CONNECT( CONNECT(WLAN) WLAN) 1. Download Baby To Sleep from AppStore / GooglePlay. your router and can browse internet. 2. You will need the username and password pair to connect to the router. PLATFORMS Your router needs to be in DHCP mode, and dispatching IP CATEGORY PARAMETER SYSTEM iOS4.3 addresses. 3. ANDROID CPU: 800MHz HARDWARE RAM:512MB at 1. 4. Run your APP.