Page 1 of 15 2003-03-21 Release 1.
Software Reticle Read – Write Station – Stand Alone Technical Reports, Release 1.1 IMPORTANT NOTE.................................................................................. 3 1 HARDWARE DESCRIPTION.................................................................. 3 2 SOFTWARE SPECIFICATION............................................................. 4 3 HARDWARE........................................................................................... 6 3.1 3.2 4 SOFTWARE.....................
Software Reticle Read – Write Station – Stand Alone Technical Reports, Release 1.1 Important Note This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Software Reticle Read – Write Station – Stand Alone Technical Reports, Release 1.1 2 Software Specification The Reticle Read/Write Station is used to write the RSP data, which will be read from the barcode labels on the top of the RSP, to the RF tag of the RSP. Barcode Data: All bar codes are code 69 labels. Label one is the product name, the second is the layer / version and the third is the CID.
Software Reticle Read – Write Station – Stand Alone Technical Reports, Release 1.1 Logistical layout of functionality: 1. 2. 3. 4. 5. 6. RSP will be placed on Reticle Read / Write Station. The RF tag will be read automatically and the result will be shown on the display. The operator writes the label data to the tag. Therefore he reads the labels with the bar code reader. If the bar codes were read correctly the operator verifies the data.
Software Reticle Read – Write Station – Stand Alone Technical Reports, Release 1.1 3 Hardware 3.1 Bar Code Reader The barcode works with an ASCII protocol which uses the following settings, COM settings: 38.400,N,8,1 (baud rate, parity, data bits, stop bits). The bar code reader is configured as follows: 1.Set all defaults: 2. Fujitsu RS-232C 3. Baud rate 38.400 Note: If the BCR is not configured you have to read these labels in the right order. 3.
Software Reticle Read – Write Station – Stand Alone Technical Reports, Release 1.1 4 Software After the equipment was connected to the power supply, the tag reader tune the antenna automatically. If no RSP is placed on the station, the software version is displayed on the display. 4.1 Functionality of Buttons Read The ‘Read’ button starts reading all 17 pages of the tag and displays the main contents (product name, version/layer, CID) on the display.
Software Reticle Read – Write Station – Stand Alone Technical Reports, Release 1.1 Reset The ‘Reset’ button is used to clear the data in the reader memory or to clear the whole tag. To clear the memory of the reader, only press the ‘Reset’ button. The display shows “Buffer cleared” and blank data. To clear the whole tag, press the ‘Reset’ button for more than 3 seconds and confirm the following question with the ‘Verify’ button. Page 1 to page 17 will be filled with the value 0x00.
Software Reticle Read – Write Station – Stand Alone Technical Reports, Release 1.1 The CID is defined as an ASCII value. Lowest value is (0x20), up to (0x7F). The CID is displayed without of characters which are less than 0x31 hex = ASCII ‘1’ as leading digit. e.g.: CID: 0000000000120034 displayed as 120034 (leading ASCII ‘0’) CID: 0x00..
Software Reticle Read – Write Station – Stand Alone Technical Reports, Release 1.1 5 Flowcharts 5.1 Normal Mode Power up Event: Remove pod Reticle SMIF Pod Read/Write Station by HERMOS Informatik GmbH Software Version: 1.3 Event: Place pod Write button Read button Yes barcode read? Verify button No press long? No read 1. label / read 2. label / read 3.
Software Reticle Read – Write Station – Stand Alone Technical Reports, Release 1.1 5.
Software Reticle Read – Write Station – Stand Alone Technical Reports, Release 1.1 5.
Software Reticle Read – Write Station – Stand Alone Technical Reports, Release 1.1 5.
Software Reticle Read – Write Station – Stand Alone Technical Reports, Release 1.1 6 Dec 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 ASCII table Hex 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F Ctrl ^@ ^Â ^B ^C ^D ^E ^F ^G ^H ^I ^J ^K ^L ^M ^N ^O ^P ^Q ^R ^S ^T ^U ^V ^W ^X ^Y ^Z ^[ ^\ ^] ^^ ^_ Code NUL SOH STX ETX EOT ENQ ACK BEL BS HT LF VT FF CR SO SI DLE DC1 DC2 DC3 DC4 NAK SYN ETB CAN EM SUB ESC FS GS RS US
Software Reticle Read – Write Station – Stand Alone Technical Reports, Release 1.1 Dec 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 Hex 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5D 5E 5F Char @ A B C D E F G H I J K L M N O P Q R S T U V W X Y Z [ \ ] ^ _ Dec 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 Hex 60 61 62 63 64 65 66 67