TM SIMP HOME ® LIFE BY DESIG N TM GATSBY / MARSHAL / BROCKTON FLOOR STORAGE CABINET MODEL # AXCBCGAT-01 1/16
TM SIMP HOME ® LIFE BY DESIG N TM Questions, problems, assembly help, missing parts? No need to return the product, we will gladly help and ship your replacement parts free of charge Please call Customer Service at 1-866-518-0120 ext. 262 Monday to Friday between 9 am –4 pm EST or go to www.simpli-home.
IMPORTANT : Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference. SAFETY INFORMATION CAUTION: Injuries and damage can occur from furniture tip over if product is not properly anchored to the wall. Use the Furniture Anti-Tipping Restraint provided with the product. Consult our assembly instructions for help.
IMPORTANT : Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference. CARE and MAINTENANCE Perhaps the greatest environmental damage to wood furniture comes from wide swings in relative humidity (RH) in our homes. Wood absorbs and desorbs water as relative humidity rises and falls, and in doing so it swells and shrinks. Making matters worse, it expands and contracts unequally along different grain directions.
PRE-ASSEMBLY INFORMATION . PART DESCRIPTION A MODEL # AXCBCGAT-01 . . BL BR ntaAv /onFrt /onFrt ntaAv ntaAv /onFrt TOP QTY 1 . LEFT SIDE QTY 1 . C RIGHT SIDE QTY 1 . D SHELF QTY 1 BOTTOM & MIDDLE SHELF QTY 2 . E . F . G BACK BAR QTY 1 FRONT BAR QTY 1 H BACK PANEL QTY 1 DOOR QTY 1 NEED HELP? For help with assembly or if you are missing a part, Please call customer service at 1-866-518-0120 ext.
PRE-ASSEMBLY INFORMATION . HARDWARE DESCRIPTION 1 2 . CAM LOCK PIN CAM LOCK QTY 12 SETS . MODEL # AXCBCGAT-01 . 3 WOOD DOWEL Ø8 X 30mm QTY 8 . 4 HINGE QTY 2 . 5 . 7 . 8 PHILLIPS SCREW ROUND HEAD M4 X 15mm QTY 12 HANDLE M4 X 25 mm QTY 1 SET PHILLIPS SCREW M3 X 15mm QTY 12 MAGNET AND PLATE QTY 1 SET . 6 9 M a.4X25mmQ - TY2 1(siextra) M b.4X15mmQ - TY1 M c.
COMPONENTS-KEY DIAGRAM MODEL # AXCBCGAT-01 For/nt A Avant F C G BL BR D For/nt For/nt Avant Avant C E H 7/16
ASSEMBLY MODEL # AXCBCGAT-01 P STEP-1 X 1 1 1 1 ntaAv /onFrt BR 1 5 1 ntaAv /onFrt 4 BL 1. Attach Cam Lock Pins 1 into pre-drilled holes on each part BL , BR . 2.AttachMagnet4usingPhilpsScrews5intopre-driledholesLeftSideBL. 3. Use Phillips screwdriver to secure Cam Lock Pins and Scews. Do not over-tighten. 2 F E 4. Insert Dowels 2 into guide holes on parts E , F . 5. Use rubber mallet to tap Dowels 2 into bottom of holes securely. 1/2 length of Dowels should be exposed.
ASSEMBLY MODEL # AXCBCGAT-01 STEP-2 A Frt /on ntaAv C C ntaAv Frt /on BL 1 A C /onFrt ntaAv C /onFrt ntaAv BL 1. Align Cam Lock Pins with guide holes and attach parts A , C to part BL . 2. Insert two Cam Locks 1 into guide holes on each part A , C . 3. Use Phillips screwdriver to secure Cam Locks.
ASSEMBLY MODEL # AXCBCGAT-01 STEP-3 F E A C C /onFrt tnaA v BL F A C E C /onFrt tnaA v BL 1. Align Wood Dowel with guide hole on part BL and attach parts E , F to part BL .
ASSEMBLY MODEL # AXCBCGAT-01 STEP-4 F Fron/t A Avant BR C Fron/t C Avant BL E 1 A BR Fron/t C Avant Fron/t C Avant BL 1. Repeat Step-2, 3 for the Right Side BR .
ASSEMBLY MODEL # AXCBCGAT-01 Note: Thebackofthecabinetframedoesnothave pre-driledholestoattachthebackpanels. STEP-5 For/nt Avant 7 For/nt Avant G 1. Attach the Back Panel G to back frame using Phillips Screws Round Head 7 through guide holes from Back Panel. 2. Use Phillips Screwdriver to tighten screws. Do not over-tighten. STEP-6 Aanvt /oFrnt Aanvt /oFrnt D 8 1. Use four Shelf Supports 8 for Shelf D in desired location .
ASSEMBLY MODEL # AXCBCGAT-01 STEP-7 4 5 6 H 3 5 1.AttachHinges3toDoorHusingPhilpsScrews5intopre-driledholesonDoorH. 2.AttachMagnetPlates4totopcornerofDoorHusingPhilpsScrews5into pre-driledholesonDoorH. 3. UsePhilpsscrewdrivertoattachHandle6toDoorH. STEP-8 H BR 5 1.AttachHingeonDoorHtoRightSideBRusingPhilpsScrews5intopre-driled holesonRightSideBR. 2. Use Phillips screwdriver to secure screws.Donotover-tighten.
FURNITURE TIP OVER RESTRAINT ASSEMBLY WARNING Serious or fatal crushing injuries can occur from furniture tip-over. If the furniture tip over restraint kit is not in the box, please contact our customer service department in order to obtain another kit before using the furniture. STEP-9 NOTE: The screwdriver is not included in the hardware pack.
FURNITURE TIP OVER RESTRAINT ASSEMBLY Furniture Tip Over Restraint Instructions: 1. Attach one of the mounting brackets securely to the back edge of the furniture. Use the shorter screw. x P 2. Determine where furniture is to be placed and mark location on the wall for mounting bracket screw hole approximately 2 inches below the bracket mounted to the furniture. x 3. 4. 5. 6. 7. P Drill a 3/16 inch hole in the wall.
TM SIMP HOME ® LIFE BY DESIG N TM WARRANTY Thank you for purchasing a Simpli Home – Wyndenhall – Brooklyn + Max product. These products have been made to demanding, high-quality standards and are guaranteed for domestic use against manufacturing faults for a period of 12 months from the date of purchase. This warranty does not affect your statutory rights. In case of any malfunction of your product (failure, missing parts, etc.) please contact us at our toll free service line at 1-866-518-0120 ext.