Installation Guide

ManualsBrandsBrondell ManualsAccessoriesBrondell PureSpa Dual Temperature Bidet Attachment

INSTALLATION

Check Water Supply Line

Check the water supply line that connects the toilet tank ﬁll valve to the water

shuto valve at the wall. If it is a rigid pipe, you will need to purchase a ﬂexible

water supply hose to replace it before installing the PureSpa. The length of the

hose may vary and the top connection size should be 7/8” Ballcock to connect to

the T-valve that you will install under the toilet tank and the bottom connection will

vary (most common are 3/8” and 1/2” female compression).

IMPORTANT

Please be advised that the provided

Cold Water T-Valve should be

installed at the Fill Valve under the

toilet tank, and NOT at the cold water

supply coming from the wall.

Note: the Hot Water T-Valve will be

installed at your hot water supply

under your bathroom sink.

If you do not have access to the Fill

Valve under the toilet tank, contact

Brondell Customer Service at

888.542.3355. We may be able to

guide you through the process.

BEFORE INSTALLATION

Check the size of the hot water supply connection (most likely under the sink/wash

basin). This needs to be a ⁄” connection for our T-valve to install.

Note: if the connection is a ½” connection, you will need to purchase the following

reducing adapter available online and at many plumbing hardware stores:

Reducing Adapter, ½” Female NPT x 3/8” Male Compression.

Summary of content (7 pages)

PAGE 1
INSTALLATION IMPORTANT Please be advised that the provided Cold Water T-Valve should be installed at the Fill Valve under the toilet tank, and NOT at the cold water supply coming from the wall. Note: the Hot Water T-Valve will be installed at your hot water supply under your bathroom sink. If you do not have access to the Fill Valve under the toilet tank, contact Brondell Customer Service at 888.542.3355. We may be able to guide you through the process.
PAGE 2
INSTALLATION (cont.) CONNECTING THE COLD WATER SUPPLY 1. Remove existing toilet seat a. Lift hinge covers and use flathead or Phillips head screwdriver to remove the mounting bolts. Alternatively, you may need to loosen mounting bolts underneath the seat. b. Remove the toilet seat and set the seat, mounting bolts and hardware aside. Step 1b 2. Turn off water supply valve and flush toilet a. Turn off water supply at the wall to stop flow of water. b.
PAGE 3
CONNECTING THE COLD WATER SUPPLY (cont.) 4. Connect Bidet Hose to T-Valve a. Connect one end of the braided metal cold water bidet hose to the remaining open side of the installed T-valve. Step 4a IMPORTANT If you are only connecting the cold water supply, you must install the Hot Water Supply Cap (provided - see Page 3) over the hot water connection on your PureSpa (see diagram). Failure to connect or cap the hot water supply will result in leaking during use.
PAGE 4
INSTALLATION (cont.) CONNECTING THE HOT WATER SUPPLY 1. Connect the hot water supply a. Locate the hot water supply line in your bathroom under your sink/washbasin and turn the water supply valve all the way off. b. Drain the hot water line by turning on the sink tap on the hot setting until no more water comes out. c. Disconnect hot water supply hose to sink from shut off valve. You may have to use a 3/8” compatible wrench or a similar tool (not supplied).
PAGE 5
CONNECTING THE HOT WATER SUPPLY (cont.) b. Push the Hot Water Flex Tubing over the Pressure Connector. IMPORTANT: Be sure to slide the Hot Water Flex Tubing over the Pressure Connector until the tubing slides past the “lip” of the pressure connector and it cannot go any further. Step 4b c. Slide the Pressure Cap down until the cap meets the Pressure Connector. Screw the Cap onto the T-Valve until secure and tight. Caution: Do not over-tighten the Pressure Cap. You will risk damaging the tubing.
PAGE 6
INSTALLATION (cont.) INSTALLING THE BIDET ATTACHMENT (cont.) b. Make sure the adjustable brackets line up with the holes in the toilet fixture. You may need to move the adjustable brackets accordingly to line up properly. Step 1b c. Replace the toilet seat on top of bidet attachment and secure using original toilet seat hardware. Make sure to tighten so that the bidet attachment and seat do not move. Step 1c 2. Connect Cold Water Bidet Hose to Bidet Attachment a.
PAGE 7
INSTALLING THE BIDET ATTACHMENT (cont.) b. Slide the Pressure Cap over the open end of the of Hot Water Flex Tubing with the inside threads facing towards the open end. Step 2b c. Push the Pressure Connector into the open end of the of Hot Water Flex Tubing with the washer facing out. IMPORTANT: Be sure to slide the Hot Water Flex Tubing over the Pressure Connector until the tubing slides past the “lip” of the pressure connector and it cannot go any further. Step 2c d.