PCMCI A 11M Wireless LAN Card User Manual Rev 0.
Regulatory Compliance FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Wireless LAN card user manual This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. CE Mark Warning This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. About this manual This manual describes how to install and operate your Wireless LAN card. Please read this manual before you install the product.
Preface Table of contents CHAPTER 1 .................................................................................................... 1 Introduction 1 Features ............................................................................................... 1 What is Wireless LAN? ........................................................................ 2 LAN Modes .......................................................................................... 3 Notes on wireless LAN configuration ..............
Cha pt e r 1 Introduction Thank you for purchasing the Wireless LAN card. This high-speed Wireless LAN card provides you with an innovative wireless networking solution. The Card is easy to set up and use.
Wireless LAN card user manual What is Wireless LAN? Wireless Local Area Network (WLAN) systems offer a great number of advantages over traditional wired systems. WLANs are flexible and easy to setup and manage. They are also more economical than wired LAN systems. Using radio frequency (RF) technology, WLANs transmit and receive data through the air. WLANs combine data connectivity with user mobility.
—Introduction LAN Modes Wireless LANs can be configured in one of two ways: Ad-hoc Networking Also known as a peer-to-peer network, an ad-hoc network is one that allows all workstations and computers in the network to act as servers to all other users on the network. Users on the network can share files, print to a shared printer, and access the Internet with a shared modem.
Wireless LAN card user manual Notes on wireless LAN configuration When configuring a wireless LAN (WLAN), be sure to note the following points: • Optimize the performance of the WLAN by ensuring that the distance between access points is not too far. In most buildings, WLAN cards operate within a range of 100 ~ 300 feet, depending on the thickness and structure of the walls. • Radio waves can pass through walls and glass but not metal.
Cha pt e r 2 Hardware installation This chapter covers inserting your Wireless LAN card in the PCMCIA slot of notebook, and connecting the card to a network. What’s in the package Please ensure that the following items are included in your package. If any items are missing, contact your dealer.
Wireless LAN card user manual Inserting the Wireless LAN card Note! These instructions apply to most notebook computers. For detailed information on inserting PC cards into your notebook, consult the notebook manual. Follow the procedure below to install the Wireless LAN card. 1. With 68-pin connector of the card facing the PCMCIA slots on notebook, slide the card all the way into an empty slot. 2. Connect to a network.
—Hardware installation Status LEDs The following table describes the meaning of the LEDs: LED MEANING PWR Indicates that the Card is powered on. LINK Indicates link status. It is normally blinking. When blinking, indicates that the card is scanning the channels, and the link is not active. When lit, indicates that the card is locked to a channel, and the link is active.
Wireless LAN card user manual dows 2000/ME/98/95 online help for information on stopping the Wireless LAN card. Most notebooks have an eject lever or button for ejecting PC cards from the PC slots. Consult your notebook manual for details. Warning! To prevent data loss, do not eject the Wireless LAN card when a data transmission is taking place. Exit your communications program normally, stop the card if necessary, and then remove the card. This concludes Chapter 2.
Cha pt e r 3 Driver installation for Windows The following sections cover Wireless LAN card driver installation in the Windows 2000/ME/98/95/NT operating systems. Driver installation for Windows 95 There are two popular versions of Windows 95, one is for retail version (ver 4.00.950), and the other is OEM Service Release 2 (ver 4.00.950B). To know which version you are using, click to run the System icon in Control Panel. You will see the following window pops up.
Wireless LAN card user manual From the General tab, the system information shows you the version number of your windows. Install Drivers on the Windows 95 OSR2 1. Insert the Wireless LAN card into an available PCMCIA slot in your notebook (refer to page 錯誤! 尚未定義書 籤。 - Inserting the wireless LAN card). 2. After Windows 95 detects the card, the Update Device Driver Wizard window appears: 3. Insert the driver disc and click Next to continue the installation.
—Driver installation for Windows 4. Click Other Locations to bring up the following window: 5. Type K: where K is your CD-ROM drive letter. Then click OK.
Wireless LAN card user manual 6. Click Finish to continue. Windows may prompt you the following window to ask you insert the disc. 7. Click OK to continue.
—Driver installation for Windows 8. Again type K: where K is your CD-ROM drive letter and click OK. After copying the driver files. Windows 95 prompts you to restart the system. Click Yes to continue the installation. Note! If you did not install the Windows 95 OSR2 from your hard drive, Windows will prompt you to input the path to the Windows 95 CD-ROM. Follow the instructions on your screen, then click OK to continue. 9.
Wireless LAN card user manual 3. Click OK. The Windows prompt you to give the path of driver files. 4. Type K: where K is your CD-ROM drive letter. Insert the driver disc into CD-ROM drive. Then click OK. 5. The windows will start copying files from disc and install the drivers. After the step, the installation is complete and you should reboot the system. After you rebooted the computer, system will start to install Wireless utility automatically. Please refer to procedures at Chapter 4.
—Driver installation for Windows Driver installation for Windows 98 Follow the steps below to install the Wireless LAN card drivers for Windows 98. 1. Insert the Wireless LAN card into an available PCMCIA slot on your notebook (refer to page 錯誤! 尚未定義書 籤。 - Inserting the Wireless LAN card). 2. After Windows 98 detects the Wireless LAN card, the Add New Hardware Wizard window appears: 3. Click Next to continue the installation.
Wireless LAN card user manual 4. Select Search for the best driver for your device. (Recommended) and click Next. The following screen appears: 5. Ensure that the CD-ROM drive box is checked. 6. Insert the driver CD-ROM into your CD-ROM drive and click Next.
—Driver installation for Windows 7. Click Next. Windows 98 copies files to your hard disk drive, and you see the following screen: 8. Click Finish. You should reboot your system to finish the installation.
Wireless LAN card user manual quired system files and will prompt you to input the path to the files. Follow the instructions on your screen, and then click OK to continue. After you have rebooted the computer, system will start to install Wireless utility automatically. Please refer to procedures at Chapter 4. Driver installation for Windows 2000 Follow the steps below to install the Wireless LAN card drivers for Windows 2000. 1.
—Driver installation for Windows 3. Click Next to continue the installation. A screen appears prompting you to select an installation method: 4. Select Search for a suitable driver for my device (recommended) and click Next.
Wireless LAN card user manual 5. Ensure that the CD-ROM drivers box is checked and insert the driver disc into CD-ROM drive. Click Next to continue. The following screen appears: 6. Click Next to continue. The following screen appears: 7. Click Yes to continue.
—Driver installation for Windows 8. Click Finish to complete the installation. 9. Then system will start to install Wireless utility automatically. Please refer to procedures at Chapter 4.
Wireless LAN card user manual Driver installation for Windows NT 4.0 This installation procedure assumes that you have installed the network component on your computer. To check whether the network component has been installed, double click the Network icon in the Control Panel. If it has not been installed, refer to the Windows NT 4.0 installation guide for instructions on installing the component. Follow the steps below to install the driver. 1.
—Driver installation for Windows 4. Click Add to add a new adapter. The following screen appears: 5. Click Have Disk. The following screen appears: 6. Type K:\ Winnt40 where K is your CD-ROM drive letter. Insert the driver disk, and click OK. After finding the installation file, the Select OEM Option window is displayed.
Wireless LAN card user manual 7. Select PCMCIA WLAN Card v2.5 and Click OK. Windows will configure the Wireless LAN card. You are returned to the Network window. 8. Click Close to exit the Network window. Windows NT 4.0 will bind the adapter with the network component and you will be prompted to restart the system. When Windows NT is finished binding the adapter to the network component, you are prompted to restart the system.
—Driver installation for Windows 9. Click Yes to finish the installation. 10. After you have rebooted the computer, system will start to install Wireless utility automatically. Please refer to procedures at Chapter 4.
Wireless LAN card user manual Driver Installation for Windows ME Follow the steps below to install the Wireless LAN card drivers for Windows ME. 1. Insert the Wireless LAN card into an available PCMCIA slot on your notebook (refer to page 錯誤! 尚未定義書 籤。 - Inserting the Wireless LAN card). 2. After Windows ME detects the Wireless LAN card, the Add New Hardware Wizard window appears: 3. Select Automatic search for a better driver (Recommended) and insert the driver disc into CD-ROM drive.
—Driver installation for Windows 5. Click Finish. You should reboot your system to finish the installation. Note! Windows ME may need to copy required system files and will prompt you to input the path to the files. Follow the instructions on your screen, and then click OK to continue. After you have rebooted the computer, system will start to install Wireless utility automatically. Please refer to procedures at Chapter 4.
Cha pt e r 4 Using the Wireless Utility The following sections cover the Wireless LAN card utility installation and usage. Installation in Windows After you have installed the wireless LAN card driver and have rebooted the computer. Please follow the steps below. 1. Execute SETUP.EXE in your CD-ROM drive. 2.
—Using the Wireless Utility 3. Select PCMCIA 11M WLAN Card v2.5 and click Next, the following screen appears: 4. Click Next.
Wireless LAN card user manual 5. Read the End User License Agreement and click Yes. The following screen appears: 6. Type in a System ID name for your wireless LAN. This system ID identifies all computers in the wireless LAN. Then click Next.
—Using the Wireless Utility 7. Choose the Network Mode for your wireless node. 8. Click Next. The following screen appears: 9. Select the default path for the wireless utility or browse to an alternate path. Then click Next.
Wireless LAN card user manual 10. Type in a Program Folder name or select the default name and click Next. Setup installs the software and the following screen appears: 11. Click Finish to finish the utility installation.
—Using the Wireless Utility After you have installed the utility, you will see the wireless utility icon in the Windows taskbar: FreePort utility icon Icon Meaning Green: indicates a connection is active. Red: indicates no connection is active. Yellow: indicates that the wireless LAN card is looking for an available access point. Double-click the icon to open the configuration utility.
Wireless LAN card user manual The following table describes the configuration utility: State: displays the connection status. Current Channel: displays the channel. Current Tx Rate: displays the wireless bandwidth in megabits per second. Throughput: displays the transfer and receive rates in bytes per second. Link Quality: when connected to the wired LAN, displays the connection integrity. Signal Strength: when connected to the wired LAN, displays the signal strength.
—Using the Wireless Utility The Encryption window enables you to create an encryption scheme for Wireless LAN transmissions. You can also manually enter a set of values for each key. Note: 128-bit encryption requires more system resources than 64-bit encryption. Use 64-bit encryption for better performance. This screen displays the version number of the Wireless LAN card and the Configuration Utility.
Wireless LAN card user manual Using the Wireless Utility The following example will help you set up a peer-to-peer connection with the Wireless LAN card. Note! For information on connecting your wireless LAN card to the LAN, contact your system administrator. 1. Insert a Wireless LAN card into the PCMCIA slots of two Notebook PCs. 2. Install the card drivers on both notebook computers (refer to Chapter 3). 3. Install the software on both notebook computers (refer to page 錯誤! 尚未定義書籤。). 4.
—Using the Wireless Utility 5. Click the Configuration tab: 6. Select 802.11 AdHoc from the Mode dropdown list. The SSID should be the same as the one that you entered when installing the software. Leave the other settings at their default values. 7. Perform steps 1 through 3 on another notebook PC.
Wireless LAN card user manual 8.
Appe ndix A Troubleshooting Q&A These guidelines give you tips to deal with some problems you may encounter while using the Wireless LAN card. If the problems remain unsolved, contact your dealer for assistance. Problem: Windows can not recognize the card. Solution: Please check if PC Card support is installed. Double-click the PC Card icon on Control Panel. If PC Card support is not activated, you should activate it now. Problem: Ejecting the card from the PCMCIA socket hangs or reboots the computer.
Wireless LAN card user manual Solution: The card can be detected by clicking Refresh in Device Manager. Question: What is the Microsoft digital signature? Answer: Drivers that pass Microsoft Windows 2000 certification receive a digital signature file from Microsoft. The Wireless LAN card does not have such a digital signature, however it is fully compatible with Windows 2000. Question: The Wireless Utility icon on system tray is always red. Answer: Please make sure that all clients have the same SSID.
Appe ndix B Specifications Standards Compliance: IEEE802.11b WLAN Standard, PCMCIA 2.1 and JEIDA 4.2 Standard Socket Interface: 68-pin 16-bit PCMCIA socket connector Card Size: PCMCIA extended Type II Frequency: 2.4 to 2.4835GHz ( Industrial Scientific Medical Band ) Antenna: Built-in strip Antenna Roaming: 802.11 compliant Data Rate: 11Mbps / 5.5Mbps / 2Mbps / 1Mbps Modulation Technique: Direct Sequence Spread Spectrum BPSK / QPSK / CCK Coverage Area: Indoor : 50m @ 11Mbps, 80m @ 5.
