Installation Guide

ManualsBrandsBroan ManualsAccessoriesHandheld Remote Control for Broan® EWP1 and EWT1 Chimney Range Hoods

MODEL HCR4

1105180A

1 - Turn range hood on. Within a 15-second period, press and hold the POWER ON/OFF button on the hood for 5 seconds. Buttons

backlighting will flash. Press each button on the remote control one after the other to pair the remote control with the hood.

2 - Use the remote control as follows:

- Press the LIGHT BUTTON to turn the lights on at high intensity. The backlight of the button will turn on.

- Press the LIGHT BUTTON again to turn the lights on at low intensity.

- Press the LIGHT BUTTON once again to turn the lights off. The backlight of the button will turn off.

- Press the UP BUTTON to turn the blower on at low speed. The backlight of the button will turn on. The LED display shows “1”.

- Press the UP BUTTON again to turn the blower on at medium/low speed. The LED display shows “2”.

- Press the UP BUTTON once again to turn the blower on at medium/high speed. The LED display shows “3”.

- Press the UP BUTTON another time to turn the blower on at high speed. The LED display shows “4” (only available with 600

CFM setting).

- Press the DOWN BUTTON to decrease blower speed. The backlight of the button will turn on. The LED will display current

speed. When the blower is set at low speed (LED display showing “1”), pressing another time the DOWN BUTTON will turn the

blower off as well as the backlight of the button.

- Press the 15-MIN DELAY BUTTON while the blower is on to activate the delay function. The backlight of the button will turn

on. The hood will run for 15 minutes. Once the 15-minute period elapsed, the blower and lights will turn off automatically.

- To cancel the delay function before the end of the 15-minute period, press another time the 15-MIN DELAY BUTTON or

change the blower speed using the UP BUTTON or the DOWN BUTTON. The backlight of the 15-MIN DELAY BUTTON will

turn off.

3 - If the remote control is not working, try to pair it again with the hood. Perform the following steps:

- Press and hold the POWER ON/OFF button on the hood for 5 seconds. Buttons backlighting will flash.

- Press and hold the POWER ON/OFF button on the hood for 5 seconds another time. The hood is not paired anymore with the

remote control.

- Perform step 1.

HOW TO USE REMOTE CONTROL

LIGHT BUTTON15-MIN DELAY BUTTON

UP BUTTON

DOWN BUTTON

⚠WARNING

CHEMICAL BURN HAZARD

Keep batteries away from children.

The remote control requires a 3 V lithium button cell type CR2025.

This product contains a lithium button/coin cell battery. If a new or used lithium button/coin cell battery is swallowed or enters the body,

it can cause severe internal burns and can lead to death in as little as 2 hours. Always completely secure the battery compartment. If

the battery compartment does not close securely, stop using the product, remove the batteries, and keep it away from children. If you

think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

a) The cells shall be disposed of properly, including keeping them away from children; and

b) Even used cells may cause injury.

Summary of content (6 pages)

PAGE 1
MODEL HCR4 HOW TO USE REMOTE CONTROL UP BUTTON 15-MIN DELAY BUTTON LIGHT BUTTON DOWN BUTTON 1 - Turn range hood on. Within a 15-second period, press and hold the POWER ON/OFF button on the hood for 5 seconds. Buttons backlighting will flash. Press each button on the remote control one after the other to pair the remote control with the hood. 2 - Use the remote control as follows: - Press the LIGHT BUTTON to turn the lights on at high intensity. The backlight of the button will turn on.
PAGE 2
FCC ID: 2AZHQ-YC IC: 27143-YC Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
PAGE 3
MODÈLE HCR4 COMMENT UTILISER LA TÉLÉCOMMANDE BOUTON HAUT BOUTON ARRÊT DIFFÉRÉ 15 MIN BOUTON ÉCLAIRAGE BOUTON BAS 1 - Mettre la hotte en marche. Dans une période de 15 secondes, appuyer longuement sur le bouton MARCHE/ARRÊT de la hotte durant 5 secondes. Le rétroéclairage des boutons clignotera. Appuyer sur chaque bouton de la télécommande l’un après l’autre pour jumeler la télécommande avec la hotte.
PAGE 4
FCC ID: 2AZHQ-YC IC: 27143-YC Tous changements ou modifications qui ne sont pas approuvés par la partie responsable de la conformité pourraient annuler la possibilité d’opérer l’équipement. Cet appareil est conforme aux normes énoncées à la section 15 des règlements de la FCC et RSS 210 d’Industrie Canada.
PAGE 5
MODELO HCR4 CÓMO FUNCIONA EL CONTROL REMOTO BOTÓN ARRIBA BOTÓN APAGADO DIFERIDO 15 MIN BOTÓN LUZ BOTÓN ABAJO 1 - Encender la campana. Durante un período de 15 segundos, mantener presionado el botón ALIMENTACIÓN ENCENDIDO/ APAGADO de la campana durante 5 segundos. La retroiluminación de los botones parpadeará. Presionar cada botón del control remoto uno tras otro para sincronizar el control remoto con la campana.
PAGE 6
FCC ID: 2AZHQ-YC IC: 27143-YC Los cambios o modificaciones no aprobados expresamente por la parte responsable del cumplimiento podrían anular la autoridad del usuario para operar el equipo. Este dispositivo cumple con la Parte 15 de las Normas de la FCC y con el estándar de Industry Canada RSS (s) exento de licencia.