Installation Guide

ManualsBrandsBroan ManualsAccessoriesDehumidifier 2x4 Wall Mount Kit

In-Wall Dehumidiﬁer

2x4 Wall Mounting

Bezel Kit

Part No. 4037767

Parts Included:

1. Foam Tape - 4" Long (x6)

2. Foam Tape - 24" Long (x2)

3. Wall Bezel

4. Screw A - Wood Screws (x5)

Screw B - Sheet Metal Screws (x5)

6. Plastic Grommet / Drain Hose Bushing - May not be needed

Tools Required:

• Drill / Screwdriver

• Drywall Saw

• Bit Extender (optional)

CAUTION!

TURN OFF BREAKER BEFORE INSTALLATION.

34.1"

2.2"

17.6"

(x5)

CONTINUED

Step 1. Install Foam Tape to Bezel Kit

Identify the front side of the bezel

kit by locating the semi-circular

cutouts along the inside edge.

Install 4" foam tape to the front

as shown. Do not cover holes

for fastening.

Install 24" foam tape to the back

as shown. Do not cover holes for

fastening.

BACK

FRONT

24"

TOLL-FREE 1-800-558-1711

•

www.Broan-Nutone.com

TS-1220 10/21 Rev A

Summary of content (4 pages)

PAGE 1
In-Wall Dehumidifier 2x4 Wall Mounting Bezel Kit Part No. 4037767 2.2" Parts Included: 1. Foam Tape - 4" Long (x6) 2. Foam Tape - 24" Long (x2) 3. Wall Bezel 4. Screw A - Wood Screws (x5) 5. Screw B - Sheet Metal Screws (x5) 6. Plastic Grommet / Drain Hose Bushing - May not be needed Tools Required: • Drill / Screwdriver • Drywall Saw • Bit Extender (optional) 4 (x5) 3 34.1" 5 (x5) 6 1 2 17.6 " CAUTION! TURN OFF BREAKER BEFORE INSTALLATION. Step 1.
PAGE 2
Step 2. Prepare Wall for Install Cut a hole in the drywall 14.5" wide (stud to stud) and 32.75" tall. Route electrical wiring and drain hose from inside of the wall and hang outside of the hole. A minimum of 12" of electrical wiring and 20" of drain hose is recommended. DRAIN HOSE ELECTRICAL ELECTRICAL WIRING WIRE 12.00 " 20.00 " Step 3. Mount Bezel to Wall 14.50 " Pull electrical wiring and drain hose through the bezel opening.
PAGE 3
Step 4. Prepare In-Wall Dehumidifier for Bezel Installation Punch the appropriate knock out holes for the drain hose and electrical wiring on the dehumidifier. DRAIN HOSE KNOCK OUT ELECTRICAL WIRING KNOCK OUT OPTIONS BOTTOM VIEW OF DEHUMIDIFIER Step 5. Install In-Wall Dehumidifier to Bezel Lift and support the dehumidifier by the plastic drain pan below the evaporator coil. Two people may be required to hold and fasten the unit in place. Locate the four slotted holes on the dehumidifier.
PAGE 4
Step 6. Install Diffuser Cover Place the hooks of the front diffuser cover into the slots at the base of the dehumidifier before fastening. SECURE BOTH HOOKING LOCATIONS Locate the four holes on the diffuser cover and fasten to the dehumidifier using either Screw C (Tamper Resistant) or Screw D (Phillips Head) included with the unit. Using the tamper resistant screws requires the ¼" Hex T-15 Torx Security Bit included with the unit. C D SCREW C OR D TOLL-FREE 1-800-558-1711 • www.Broan-Nutone.