BRAN INSTALLATION AND USE & CARE INSTRUCTIONS N SAFETY Please visit our websites www.broan.com, or www.broan.ca to register this product and to view installation tips and videos. Installer: Leave this manual with the homeowner. READ AND SAVE THESE INSTRUCTIONS A To reduce the risk of fire, electric A shock, or injury to persons, observe the following: * Use this unit only in the manner intended by the manufacturer.
ALL INSTALLATIONS Start here. . COOKING AREA ——edamame N Do not install above of // inside this area, Syphilis/ NOT FOR USE IN COCKING AREA Caking Equipment Floor ¥ IMPORTANT The ducting from this fan to the outside of the building has a strong effect on the air flow, noise and energy use of the fan. Use the shortest, straightest duct routing possible for best performance, and avoid installing the fan with mailer ducts than recommended.
6. Connect 4-in. round duct. INSTALLATION AND USE & CARE INSTRUCTIONS INSTALLATION i~ NEW CONSTRUCTION For Retrofit Installation Skip to Page 5. 4, Attach connector s : to fan housing. See ooy O S Push connector through opening from inside of housing. Engage tabs and secure with screw from parts bag. 7. Connect wiring. Bend tab to expose desired access hole, Connect power cable to housing with appropriate UL approved connector. Connect black to black, white to white and green to green or bare wire.
8. Install blower. Re-install blower, Secure blower with 2 screws trim parts bag and plug blower into black receptacle. 9. Finish ceiling, then install grille. Plug light into receptacle in housing. Attach grille pan to housing with (2) rile mounting screws. install (2) 60W {Max.) candelabra bulbs (not included). Attach shade with hardware as shown. Do not over tighten finial nut. GRILLE BRACKETS [~ LIGHT PLUG (2) 6OW (MAX.
BEGAN INSTALLATION AND USE & CARE INSTRUCTIONS INSTALLATION =) 6. Connect wiring. Bend tab to expose desired access hole. Connect power cable to housing with appropriate UL approved connector. Connect black to black, white to white and green to green or bare wire. Re-install wiring panel and secure with screw from parts bag. 7. Mount fan to ceiling structure. Mount housing to selling structure with standard drywall or wood screws in locations shown, *Center hole optional. 8. Connect 4-in. round duct.
MODELS AR110PS, HERBART SERVICE PARTS Key No. | Part No. | Description 1 97018514 { Housing 97020122 | Duct Connector 4-in. §70185186 | Wire Panel Assembly 99528761 | Grille Bracket Assembly 2 3 4 47019786 | Blower Assembly 8 € 90528815 | Shade 99528817 | Shade Mounting Hardware (AR110PS) 7 99528818 | Shade Mounting Hardware (ARt 10RB) 06628820 | Rile Pan Assembly (AR110PS) 8 90528821 | Rile Pan Assembly (AR110RB) 08628683 | Light Fixture Assembly (AR110PS) A (includes Key Nos.
BRAN INSTALLATION AND USE & CARE INSTRUCTIONS ©O WARRANTY Limited Warranty Warranty Period and Exclusions: Brian-NuTone LLC (the, Company,) warrants o the original consumer purchaser of ts product { you.) that the product (ihe, Byproduct) wil be free from material defects the Product o fts workmanship for a priced of three (3) years from ihe date of origin! purchase.
BRAN DIRECTIVES D'INSTALLATION, D’UTILISATION ET D'ENTRETIEN INSTALLATION 8. Installez le ventilateur. Reposez le ventilateur. Fiez-l avec 2 vis du sachet de pièces et branchez-le dans la prise noire, 9, Finissez le plafond, puis installez la grille. Branchez la fumiger dans la prise de courant du bottier, Fixez la plaque de grills au bottier avec les deux (2) vis de montage de la gifle. Installez deux (2) ampoules candélabre de B0W {max.} (non comprises).
6. Branchez les fils. Repliez i languette pour exposer e trou ¢'accss foui, Fixez le câble d’aimantation au bottier & F'aide du connecter approprié homologue UL. Conf finir avec. I nof blanc avec le blanc, et le cerf avec e vert Reposez ie panneau de câblage et fixez-le avec fes vi se brevetant dans e sachet de piques. BRAN 7. Fixez le boîtier a la charpente du plafond. Fixez le bottier & la charpente du plafond ave des seiche ou des vis & bois ordinaires aux endroits endigués.
BECAN x INSTALACIÓN INSTRUCCIONES DE INSTALACIÓN, USO Y CUIDADO ek CONSTRUCCIÓN NUEVA Para instalaciones de conversión: pase a la paginé 19. 4. Acople el conector del regulador de tiro/conducto a la cubierta del ventilador. Pudiere e conector & través de Iz abertura desde el interior de la cubierta, Enganche las lengüetas y fijezas con los torillos de la bolsa de piezas. LENGÜETAS 5, Monte la cubierta en la estructura del cielo raso.
8. Instale el soplador. Vuelva a Instalar ef soplador. Celo con 2 tomillos de Ja besa de piezas y conecte el soplador en el receptáculo negro, 9. Termine el cielo raso y a continuación instale la rejilla. Enchute la fuz en el receptáculo Sz la cubierta. Fije el platino de la re jifia a la cubierta con dos {2) tornillos para & la. Instala dos (2) bombillos bombilla candelabros de 60 W (máximo) {no s incluyen). Filie la pantalla con los herrajes, como se muestra.
7. Monte el ventilador en la estructura dei cielo raso. 6. Conecte el cableado. Monte ia cubierta en |a resinificara del ciego raso con tomillos Doble i lengüeta para exponer €l oficio de acceso deseado. restingar para madera o yeso ef [0 Lugares que se musitan. Conecte el cable eléctrico a la cubriere con ria conexión “El orificio central 25 opcional. apropiada aprobada por UL, Conecta negra con negra, banco con bance y verde con verde o con ¢l libo desnudo.