ENGLISH (UK) REFERENCE GUIDE CT2200HDV
Preliminary Pages ENGLISH (UK) ITALIANO Please read this first! LEGGERE QUESTO AVVISO PER PRIMO! If you do not understand the contents of this manual: Do not operate this equipment. Se non si capisce il contenuto del presente manuale NON UTILIZZARE L’APPARECCHIATURA. Also, translation of this manual into any EC official language can be made available, at your cost. È anche disponibile la versione italiana di questo manuale, ma il costo è a carico dell’utente.
Preliminary Pages List of Contents Chapter 1: Introduction to the CT2200HDV Gives a general description of the equipment and its main features and functions. Identifies the controls, indicators and connectors on the front and rear panels. Chapter 2: Installing the Equipment Provides a guide to the suitability of an installation and gives detailed procedures for the preparation and installation of the equipment. Also details the external connectors and provides important safety information.
Preliminary Pages Contents Preliminary Pages List of Contents ........................................................................................ ii About this Reference Guide ........................................................................vi Nomenclature...........................................................................................vi Acknowledgements .................................................................................. vii General......................................
Preliminary Pages Appendix A List of Abbreviations Appendix B Technical Specification B.1… Compliance .................................................................................. B-1 B.1.1 Safety ................................................................................... B-1 B.1.2 EMC ...................................................................................... B-1 B.1.3 Shock and Vibration ................................................................ B-2 B.1.4 CE Marking ....
Preliminary Pages About this Reference Guide This Reference Guide provides instructions and information for the installation and operation of the CT2200HDV. This Reference Guide should be kept in a safe place for reference for the life of the equipment. It is not intended that this Reference Guide will be amended by the issue of individual pages. Any revision will be by a complete reissue. Further copies of this Reference Guide can be ordered from the address shown on page ix.
Preliminary Pages Acknowledgements General All best endeavours have been made to acknowledge registered trademarks and trademarks used throughout this Reference Guide. Any notified omissions will be rectified in the next issue of this Reference Guide. Some trademarks may be registered in some countries but not in others. Registered trademarks and trademarks used are acknowledged below and marked with their respective symbols. However, they are not marked within the text of this Reference Guide.
Preliminary Pages Warnings, Cautions and Notes Heed Warnings All warnings on the product and in the operating instructions should be adhered to. The manufacturer can not be held responsible for injuries or damage where warnings and cautions have been ignored or taken lightly. Read Instructions All the safety and operating instructions should be read before this product is operated. Follow Instructions All operating and use instructions should be followed.
Preliminary Pages RF Exposure Info: For body worn operation, device has been tested and meets FCC RF exposure guidelines when used with an accessory that contains no metal and that positions device a minimum of 25 mm from the body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. Technical Training Training Courses BMS Europe provides a wide range of training courses on the operation and maintenance of our products and on their supporting technologies.
Chapter 1: Introduction Introduction to the CT2200HDV Preliminary Remarks The present manual is provided for users and operators of the CT2200HDV Transmitter. It is intended to support the installation, operation, maintenance and daily use of the unit in general. The manual should be kept with the CT2200HDV Transmitter and may be consulted when questions occur.
Chapter 1: Introduction Description General Information on D-ENG (Digital Electronic News Gathering) The introduction of the DVB standard established the basis for digital broadcast video transmission making efficient use of the available bandwidth. Powerful compression algorithms allow a reduction in the amount of data to be transferred, while maintaining the high quality standards for video and audio signals used in broadcasting applications.
Chapter 1: Introduction Video Inputs The CT2200HDV accepts only HDV encoded information at the input: • HDV IEEE-1394a (Firewire) CT2200HDV operates with all currently available HDV cameras. OFDM Modulator The digital data signal for wireless transmission is processed by the OFDM Modulator and following IQ MOdulator. The OFDM (Orthogonal Frequency Division Multiplex) modulation procedure has a major impact on the transmission properties and was specifically developed for terrestrial radio transmission.
Chapter 3: Options and Upgrades Installing the Equipment Safety instructions Warning The regulations of VDE0100 must be observed for installation and operation of the unit. Caution • Establish all other connections before starting the unit by connecting it to 12VDC. Essential a valid video signal must be connected to the desired input before power on the CT2200HDV. • When you connect the CT2200HDV as described in the following sections, make sure that the "Caution" instructions given there are observed.
Chapter 3: Options and Upgrades Connectors Figure 2 • Input connector of the CT2200HDV RF Connector The RF output signal of the Low-Power Amplifier is fed out at the SMA(f) connector on top of the unit. The CT2200HDV provides a RF output of about 400mW (+26dBm). The signal may be further amplified by a secondary amplifier optimized for HD-COFDM signals.
Chapter 3: Options and Upgrades Connecting Signal Sources The encoded Video/Audiosignal supplied by the camera have to applied to the IEEE 1394a connector of the transmitter. Connecting the RF Output A Omni directional antenna with SMA(m) connector can be directly mount at the RF out socket. Connecting the 12VDC Supply Voltage Caution When using a battery or power pack, make sure that the maximum supply current is at least 3A and the output voltage matches the input voltage range of the CT2200HDV.
Chapter 4: Operating the Equipment Operating the Equipment Multifunctional display Button 1 Button 2 Button 3 During power up time the display of the CT2200HDV pass a self test. It displays manufacture, transmitter type and software version. BMS HDV SW v 0.88 After the selftest, the current frequency is displayed. 2350.0MHz With its automatically COFDM setup the customer menu is very easy to handle. Due to press and hold the button 3 for approximately 2sec. the setup menu is accessibly.
Chapter 4: Operating the Equipment Frequency input In the Submenu „Frequency“ the current frequency is displayed. ** setup: ** Frequency 2350.0 To change the frequency press button 3 for approximately 2 sec. ** setup: ** Frequency 2350.0 The flashing curser indicates the current changing position of the frequency. With button 1 or 2 the marked digit can be increased or decreased about one digit. To change the next lower digit, press button 3 and repeat the step before.
Chapter 4: Operating the Equipment Automatical display cutoff The display can be set to turn off automatically after a preset time of inactivity. Select "Disp off" submenu and press button 3 for 2 seconds. Use buttons 1 and 2 to set value. Set the desired time-out interval between 015 to 240 seconds. A value of 000 (default) causes the display to stay on continuously. ** setup: ** Disp off 000s To exit this submenu, press button 3.
Annex A: List of Abbreviations List of Abbreviations The following specific abbreviations are used within this document: 4:2:0 Digital video coding method in which the color difference signals are sampled on alternate lines at half the luminance rate. 4:2:2 Digital video coding method in which the color difference signals are sampled on all lines at half the luminance rate.
Annex A: List of Abbreviations RS 232, RS-232 EIA-232 SDI Serial Digital Interface TS Transport Stream XLR Audio connector featuring three leads, two for signal and one for GND YUV Y: Luminance component (brightness), U and V: chrominance (color difference) Y/C Broadcast Video with separate color, Y luminance and C chroma (sometimes called S-Video) Reference Guide: CT2200HDV May 07 Page A-2
Annex B: Technical Specification Technical Specification B.1 Compliance1 B.1.1 Safety This equipment has been designed and tested to meet the requirements of the following: B.1.2 EN 60950 European Safety of information technology equipment including business equipment. IEC 60950 International Safety of information technology equipment including business equipment.
Annex B: Technical Specification B.1.3 Shock and Vibration The device chassis complies with the requirements of ETS 300-019-2-5 Table 2, for both non-operational and operational states, without any special mounting or casing requirements over and above the standard mounting requirements specified. ETS 300-019-2-5 B.1.
Annex B: Technical Specification In the major metropolitan preference will be given to TV pick-ups. Elsewhere, the level of priority access given to TV pick-ups will be at the discretion of the regional offices. To the extent possible, TV pick-up usage should avoid the spectrum designated for very low capacity systems. Arrangement: Band G(n) = 2019.5 + 12n Where: n = 1 to 7, and G(n) is the centre frequency of the channel in MHz. G1: G2: G3: G4: G5: G6: G7: 2031.50 2043.50 2055.50 2067.50 2079.50 2091.
Annex B: Technical Specification B.2 Technical Specifications Signal Parameters Output (RF) 2.3 – 2.7 GHz (standard; others on request) Connector: SMA female, 50 Ω 26 dBm (400mW) Audio/Video Inputs IEEE 1394a (Firewire) Modulator COFDM, ETS 300744, 2k carriers only Bandwidth: 8 MHz 64 QAM automatic mode for guard interval and FEC Power Input 10.2 – 17.
Annex B: Technical Specification Antenna Output SMA, female; 50 Ω Centre Shielding Reference Guide: CT2200HDV May 07 Signal GND Page B-5
Annex C: Ordering Information Ordering Information CT2200HDV Models P/N COFDM Bandwith Frequency Range * Battery bracket 11.2403.000 8 MHz 2.3 – 2.7 GHz Sony V-mount 11.2403.100 8 MHz 2.0 – 2.3 GHz Sony V-mount 11.2403.200 8 MHz 2.3 – 2.7 GHz Anton Bauer 11.2403.300 8 MHz 2.0 – 2.3 GHz Anton Bauer * Other frequency ranges on request Manufacturer: BMS-Europe GmbH & Co.
