Remoto 3 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. PART NAME: PART NO: Remoto 3 Pro TCU TCU 3.0.0.
REMOTE ENGINE START KIT Remoto 3 Pro TCU x 1 Sticker x 2 REQUIRED TOOLS Philip screw driver 10 &12 mm spanner Socket driver 10mm Plastic remover Cutter plier Mechanical Pliers 2
REMOTO 3 CONNECTIONS External GPS antenna (optional) External GSM antenna (optional) Vehicle harness socket 2
USER INFORMATION ABOUT REMOTO 3 Remoto 3 is a telematic service and information complex. The complex consists of a telematic unit connected to the system of the car through cable and the mobile application. The mobile application is installed on the smartphone of the user. Supported operation systems: 1. Android (the version from 6 and above) 2. iOS (the version from 8 and above) Remoto 3 possess functions of remote car control and informing.
IMPORTANT NOTICE: This manual has been designed for technicians who are qualified in the proper procedures of vehicle safety, handling and accessories installation. The technicians should be able to carry out installation procedures when giving instructions by an experienced technician in a supervisory role. Marks: Stop & Check Stop proceedings & check the notes to avoid any vehicles damage. Safety Concern Operate carefully to protect yourself from injury.
REMOVE INSTRUMENT PANEL FINISH CUSHION RH Using a moulding remover , detach the 4 claws and 3 clips and remove the instrument panel finish panel cushion. Remove the clip and screw. 2. REMOVE LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY RH 3. REMOVE FRONT DOOR SCUFF PLATE RH Detach the 11 claws and guide and remove the lower instrument panel pad subassembly RH.
4. REMOVE INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY Detach the 4 claws and 3 guides. Disconnect the connector and remove the No. 2 instrument panel under cover sub-assembly. 5. REMOVE LOWER INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Passenger Side Knee Airbag VXR ) 1.Remove the 4 bolts. 2.Detach the 4 claws and remove the front passenger side knee airbag assembly. 3.Using a screwdriver, release the connector lock and disconnect the airbag connector. 7.
. REMOVE INSTRUMENT PANEL BOX DOOR KNOB Using a moulding remover , detach the 2 claws and remove the instrument panel box door knob. 9. REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL Remove the 4 screws Detach the 3 claws Disconnect the connector and remove the lower instrument panel finish panel.
1. INSTALL GLOVE BOX LIGHT ASSEMBLY Install the glove box light assembly and twist it in the direction indicated by the arrow. 2. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL 1.Connect the connector. 2. Attach the 3 claws to install the lower instrument panel finish panel. Install the 4 screws 3. INSTALL INSTRUMENT PANEL BOX DOOR KNOB Attach the 2 claws to install the instrument panel box door knob. 4. INSTALL NO.
5. INSTALL LOWER INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Passenger Side Knee Airbag) 1.Check that the ignition switch is off. 2.Check that the cable is disconnected from the negative (-) battery terminal. 3.Connect the airbag connector and lock the connector lock. 4. Attach the 4 claws to install the front passenger side knee airbag assembly. 5.Install the 4 bolts. Notice: When handling the airbag connector, take care not to damage the airbag wire harness. 7. INSTALL NO.
ACCESSORY FUNCTIONAL VERFICATION: Check the operations of the individual functions of the accessory. Tick the box after confirming its operation. S/N Item Name Operational Description Check 1 Key transmitter Press Lock / Un lock by pressing remote 2 Start the car by PTS By Pressing push to start button 3 VEHICLE AUDITING: Check all those items which might be affected during installation of the accessory. Tick the box after confirming its operation.
How to use: Please, download and install Remoto mobile app onto your mobile device (both Android and iOS-based supported). Connected user role requires for a user to input VIN number of the car (already added to the Profile or create new car and then input VIN) and verify Connected Car with the Proof of ownership procedure. Customer can activate Dongle with 2 different ways – using Device Serial number or vehicle VIN.
Last step is a procedure of verifying Connected Car suggests user to turning off and turning on the engine (Proof of ownership) and explicitly activate automatic VHC and location tracking services. Customer activates Automatic Health Check and Vehicle location tracking to reach an access to all available in the Mobile app functions. If user decided to turn-off Automatic Health Check – system will not run VHC automatically (option can be activated in settings at any time).
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.