User's Manual

ManualsBrandsBridgestone ManualsElectronicsTPMS Hand Reader

Tire-Pressure Monitoring System

For truck and bus

For use only in Europe (model:H212) or

U.S.A. (model:H211)

Apr. 2006

Base REG Developmen

2006.04 Base

Ⓐ

Manufacturing and Sales

Bridgestone Corporation

1-10-1 Kyobashi Chuoku Tokyo 104-8340

http://www.bridgestone.co.jp/

Hand Reader

Operation Guide

Notice to user

What is a Tire-Pressure Monitoring System?

Tire-pressure monitoring system is an advanced system that

measures the tire pressure and temperature with sensors mounted

inside the tire and enables vehicle management using the measured

data.

・

This product is designed exclusively for trucks and buses.

・

This product has two design for use within Europe and USA.

It cannot be used other country due to difference in radio wave

regulations. Attention for product model number.

For Europe ...... model H212

For USA .......... model H211

・

Be sure to read and understand the content of the operation guide

before installing or removing.

・

Keep this guide in a safe place and refer to it as necessary.

Summary of content (16 pages)

PAGE 1
Tire-Pressure Monitoring System Hand Reader Operation Guide What is a Tire-Pressure Monitoring System? Tire-pressure monitoring system is an advanced system that measures the tire pressure and temperature with sensors mounted inside the tire and enables vehicle management using the measured data. Notice to user For truck and bus For use only in Europe (model:H212) or U.S.A. (model:H211) ・ This product is designed exclusively for trucks and buses.
PAGE 2
INTRODUCTION Introduction SAFETY PRECAUTIONS This guide describes how to use the hand reader for tire-pressure monitoring system (referred hereafter as "this product" or "hand reader"). Please read and understand the content before using. About This Product PART NAMES & FUNCTIONS This product can collect tire pressure and internal temperature data from the tire-pressure monitoring system sensors mounted inside the tire (rim) and save them in its memory.
PAGE 3
About Tire-Pressure Monitoring System The tire-pressure monitoring system (hereafter referred to as "system" or "this system") is a system that monitors the tire pressure and temperature using sensors mounted inside tires (rim). This system is available as "Hand Reader Type" and "On-Board Type". Purchase the product that is appropriate for your intended use.  Hand reader type This system receives the radio wave from the sensor with a portable hand reader.
PAGE 4
INTRODUCTION Operation Guide Combination The following two operation guides are necessary to use the Hand Reader type of Tire-Pressure Monitoring System. Read the guide appropriate for your system.
PAGE 5
Contents Introduction ................................................................... 1 About This Product.................................................. 1 Package Content ..................................................... 1 About Tire-Pressure Monitoring System ................. 2 Operation Guide Combination ................................ 3 Warranty and Disclaimer......................................... 3 8. Troubleshooting ....................................................
PAGE 6
INTRODUCTION Safety Precautions SAFETY PRECAUTIONS  Warning symbols This guide uses the following symbols to describe items that you must observe in order to use the hand reader safely. Read and observe these items carefully. NOTE PART NAMES & FUNCTIONS CAUTION Failure to observe this item may result in death or severe injury. Failure to observe this item may result in minor injury or property damage. Failure to observe this item may result in damage to the product.
PAGE 7
Notices for using in USA This device complies with Part 15 of the FCC Rules and IC RSS-Gen. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and IC RSS-Gen.
PAGE 8
Společnost (BRIDGESTONE CORPORATION) tímto prohlašuje, že (HAND READER:H212) splňuje základní požadavky a další příslušné ustanovení Direktivy 1999/5/EC. Estonia Sellega kinnitab (BRIDGESTONE CORPORATION), et see (HAND READER:H212) vastab direktiivi 1999/5/EC põhilistele nõudmistele ja muudele asjakohastele määrustele. Latvia Ar šo, (BRIDGESTONE CORPORATION), apstiprina, ka (HAND READER:H212) atbilst Direktīvas 1999/5/EK galvenajām prasībām un citiem tās nosacījumiem.
PAGE 9
Part Names and Functions 1-1 Part names and functions Antenna LCD panel B button REG panel Battery cover (back) Power switch LCD backlight switch PC connector (Also used as depth gauge connector) Antenna LCD panel B button REG panel Power switch Used to exchange data with sensor mounted inside the tire (rim). Displays setup menus and measurement results. Press when measuring tire pressure and internal temperature. Used to select mode and for character and number key input.
PAGE 10
Installing batteries INTRODUCTION Replacing batteries W h e n 1. Pull out the battery cover while pressing the battery cover tab. You want know when to replace batteries SAFETY PRECAUTIONS 1-2 The hand reader has a function to monitor the battery voltage. PART NAMES & FUNCTIONS BASIC OPERATION 2. Set four AAA batteries in the battery box with positive and negative poles set correctly. When the voltage is low, a batter y voltage low warning appears on the LCD panel.
PAGE 11
Removing the batteries 1. Pull out the battery cover while pressing the battery cover tab. 2. Remove the batteries. 3. Set the battery cover back and close it securely. N OT E Be sure to turn off the power before removing the battery. Otherwise, you may damage the hand reader. 1-3 Installing/removing the strap (option) 1. With the Velcro side of the strap facing up, pass the strap through the fastener at the back of the hand reader. 2. Bend the end of the strap and fasten with Velcro. 3.
PAGE 12
INTRODUCTION Basic Operation 2-1 SAFETY PRECAUTIONS This chapter describes the basic operation of the hand reader. Power ON BASIC OPERATION PART NAMES & FUNCTIONS 1. Check that the batter y is installed properly and turn on the power switch. Press T/B HANDREADR Ver3.0 RevA MES mode 2. The power turns on and the software version appears on the LCD panel (for 2 seconds). Software Version Display screen SELECT MENU 1REG 2MES 3OB REG mode 3. The Select Menu screen appears. Power OFF 2.
PAGE 13
2-3 Turning on the backlight 1. Press the LCD backlight switch ( ). SELECT MENU 1REG 2MES 3OB Press 2. The LCD panel backlight turns on. SELECT MENU 1REG 2MES 3OB Approximately 15 seconds later 3. The LCD backlight turns off automatically if there is no action for approximately 15 seconds. 2-4 SELECT MENU 1REG 2MES 3OB Selecting operation mode There are three operation modes. No.
PAGE 14
W h e n REG mode .................................. You entered the wrong operation mode number MES mode .................................. 1. Press the [BACK] key until the Select Menu screen appears. INTRODUCTION Press the 1 or 2 key to select the desired mode. SAFETY PRECAUTIONS 2. Enter the number of the desired mode with the number key. PART NAMES & FUNCTIONS Press 3. When you enter the number, the screen of the corresponding mode appears.
PAGE 15
4. After you finish entering, press the [ENTER] key to conﬁrm the entry. Press You want to move the cursor to the previous digit • If an invalid number is entered, a long alarm (1.5 seconds) sounds when you press the [ENTER] key. Enter the correct number. 2-6 W h e n Move the cursor with [«] key. Do not use the [BACK] key to move the cursor to the previous d i g i t . W h e n yo u p r e s s t h e [BACK] key, the LCD panel returns to the Previous Mode screen.
PAGE 16
Press W h e n INTRODUCTION 4. After you finish entering, press the [ENTER] key to confirm the entered character. You want to move to top or bottom line PART NAMES & FUNCTIONS You want to erase a space To e r a s e s p a c e b e t w e e n characters: 1. Press the [BACK] key to return to the previous menu. 2. Reenter the characters from the beginning. BASIC OPERATION • Depending on the input item, you may not need to enter all digits, but you cannot use space between characters.