User Manual

ManualsBrandsBrandmotion ManualsCar & Vehicle ElectronicsSilverado/Sierra Tailgate Bezel and Camera with Chassis Harness

INSTALLATIO N (IN S TR UCTIONS(

9002-9560 Instructions 9-23-16.doc GS

1 of 7

Rear Vision System – Aftermarket Display

2007-Current Chevrolet Silverado, Silverado HD; GMC Sierra,

Sierra HD (Kit part number 9002-9560)

Kit Contents:

Chassis Harness with RCA (Note: In some

cases a RCA extension may be required to

connect to your aftermarket display. Kit

#6111 may be purchased at

Brandmotion.com for these cases.)

1 bubble bag containing:

Camera/Module/Tailgate Bezel Assembly

1 bag containing:

Lock Plug (optional)

1 bag containing:

Jumper Harness

1 bag containing:

Template (along with these instructions)

Tools Required:

Socket Wrench

10mm and 13mm Sockets

T15 and T20 Torx Bits

Torque Wrench

Trim Removal Tool

Phillips and Flat Blade Screwdrivers

Delphi Terminal Tool 12094429 or a small flat

blade watch repair screwdriver

Power Drill

25.4mm (1”) Hole Saw

29mm (1-1/8”) Hole Saw

Deburring Tool

Center Punch

Electrical Tape

Vehicle Hoist

Wire Ties (recommended)

Corrosion Inhibitor (recommended)

Note: We strive to provide accurate and up-to-date installation instructions. For the latest full

color instructions, as well as an installation video, please visit www.brandmotion.com

IMPORTANT: Before beginning kit installation, verify kit contents are complete against list above.

Summary of content (7 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Rear Vision System – Aftermarket Display 2007-Current Chevrolet Silverado, Silverado HD; GMC Sierra, Sierra HD (Kit part number 9002-9560) Kit Contents: Tools Required: Socket Wrench 10mm and 13mm Sockets T15 and T20 Torx Bits Torque Wrench Trim Removal Tool Phillips and Flat Blade Screwdrivers Delphi Terminal Tool 12094429 or a small flat blade watch repair screwdriver Power Drill 25.
PAGE 2
INSTALLATION INSTRUCTIONS 8. Prepare a work surface for the Tailgate, as it will be removed. 9. Disconnect the two Tailgate support cables. Figure 3. Preparation 1. Ensure all lamps and accessories are OFF. 2. Ensure the ignition switch is in the OFF position. 3. Loosen the negative battery cable bolt. Remove negative battery cable from terminal and position away from battery. 4. Wait one (1) minute prior to working on the vehicle to assure SIR roof rail airbag system has been disabled for your safety.
PAGE 3
INSTALLATION INSTRUCTIONS Clip (1) and then the Tailgate Lock Cylinder (2). Figure 8. FIGURE 8 FIGURE 5 15. Using a power drill and a 29mm (1-1/8”) Hole Saw, cut out the harness pass-through in the Pickup Box Sill. Figure 6. FIGURE 6 20. If equipped, insert the Tailgate Lock Cylinder (2) into the new Tailgate Bezel and re-attach the Tailgate Lock Cylinder Retaining Clip (1). Figure 8. a. If the Truck is not equipped with factory Tailgate Lock, install supplied Lock Plug. b.
PAGE 4
INSTALLATION INSTRUCTIONS Determine Reverse Signal Location FIGURE 10 30. Using a Trim Removal Tool, remove Left Instrument Panel Outer Trim Cover (1). Figure 13. FIGURE 13 23. Snap the supplied Tailgate Bezel Assembly into the Tailgate. 24. Seat the second grommet (4) securely around opening. Figure 10. 25. Install remaining Tailgate Latch Handle Bolt in Tailgate and tighten all three 13mm bolts to 25 N·m (18 lb ft). 26. If present, remove the Rear License Plate. 27.
PAGE 5
INSTALLATION INSTRUCTIONS 33. If Reverse signal is NOT present in the C10/ X10 Connector or C11/ X11 Connector: FIGURE 15 A. Check that bail that secures the M-BEC connectors is fully locked. Repeat Step 33. B. If Reverse signal is still not present, check Fuse Block for any blown fuses. Figure 15. Replace any blown fuses and repeat Step 33. C.
PAGE 6
INSTALLATION INSTRUCTIONS Install Chassis Harness & Connect to Aftermarket/ NAV Display 37. Relocate M-BEC up into the IP to gain access to Front of Dash Mat Opening behind M-BEC. 38. Locate cut-out in dash Mat. Locate the dimple in the sheet metal and then use a center punch to help start a drill bit as close as possible to dimple. Using a power drill and a 25.4mm (1”) hole saw, drill out the chassis harness pass-through (2). Figure 20. 42.
PAGE 7
INSTALLATION INSTRUCTIONS 48. If all M-BEC connections were secure and no fuses were blown and Reverse was still not present, Reverse must be located in the under dash BCM left of the steering wheel. Figure 15 57. Connect the negative battery terminal. Tighten the negative cable nut to 5 N·m (44 lb in). 58. Test system functionality. 59. Re-install the Knee Bolster Assembly. Tighten Screws to 2 N·m (18 lb in). Re-install Parking Brake Release Handle and Bolt, tighten to 9 N·m (80 lb in). Figure 14. 60.