User's Manual

ManualsBrandsBQT Solutions ManualsElectronicsContactless Smart Card Reader

Table Of Contents

Drilling template

• 20mm (0.79”) diameter hole for wire entry

• 2 x 4 mm (0.16”) diameter holes for mounting screws

• Inner reader dimension is 88mm x 88 mm (3.47" x 3.47")

• Assemble reader outer dimension is 90mm x 90mm (3.54” x 3.54”)

• Reader corner radius is 4mm (0.16”)

Specifications

Output protocols

Wiegand 26-199bit, RS485 or custom configuration (Model

dependent)

BT815-WG/

MiP5/CSN5

BT815-D/D2

BT815

BT815-BM

Power requirement

12V DC

6-18V DC

7-16V DC

Current

consumption

103mA (Avg)

145mA (Peak)

157mA (Avg)

174mA (Peak)

38mA (Avg)

80mA (Peak)

45mA (Avg)

135mA (Peak)

Read range

20-40mm (0.8”-1.6”) at 12V DC depends on the type of card

used

Operating

temperature

-25’C to +65’C (-13’F to 149’F)

Relative humidity

90% max, operating non-condensing

Reader dimensions

Standard: 90mm(L) x 90mm(W) x 27mm(D) (3.54”x3.54”x1.06”)

Slim Line: 90mm(L) x 90mm(W) x 20mm(D) (3.54”x3.54”x0.79”)

Status LED

Green & Red

Audible tone

Internal and external buzzer control

Colour finish

Charcoal & Ivory

IP rating

IP65

Information obtained in this document is subject to change without notice.

For further technical information, visit our website at www.bqtsolutions.com or email

techsupport@bqtsolutions.com.

Alternatively contact us at one of our global locations

AUSTRALIA & PACIFIC

BQT Solutions (Australia) Pty Limited

Level 1, 82 Waterloo Road

Macquarie Park, NSW 2113, Australia

Phone: +61 (0)2 8817 2800

Fax: +61 (0)2 8817 2811

Email: sales@bqtsolutions.com

EUROPE AND MIDDLE EAST

BQT Solutions (UK) Limited

Regal House, 70 London Road

Twickenham, TW1 3QS

United Kingdom

Phone: +44 (0)20 8622 4428

Fax: +44 (0)20 8622 4401

Email: salesuk@bqtsolutions.com

GREATER ASIA

BQT Solutions Singapore Office

Mediapolis

71 Ayer Rajah Crescent #03-03

Singapore 139951

Phone: +65 6220 7970

Fax: +65 6220 7656

Email: salesasia@bqtsolutions.com

Wiring diagram

Note:

• A shielded cable is recommended to be used. The shield is connected to controller 0V reference

• Maximum wiegand data cable length: 150 meters (500 feet)

• Buzzer and LED are activated when buzzer and LED line go below 2.5V.

• RS485 lines and Relay lines are only for optional use.

• Some models have additional wires/connectors which are not specified in the diagram above. These wires are for other

requirements. DO NOT connect them unless specified from BQT Solutions or a BQT authorized distributor. Any damage

caused by incorrect connection will void the warranty

• Terminate or insulate all un-used wires

Regulatory Information

C-Tick: This device is C-Tick complied.

CE: The device has passed all relevant tests and obtained CE approval.

FCC: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device

may not cause harmful interference and 2) this device must accept any interference received, including interference that

may cause undesired operation of the device.

Warning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part

15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressively approved by BQT Solutions could void the user’s authority to operate this

equipment.

Series

INSTALLATION GUIDE

Version4.1

Summary of content (4 pages)

PAGE 1
Drilling template • • • • • Wiring diagram 20mm (0.79”) diameter hole for wire entry 2 x 4 mm (0.16”) diameter holes for mounting screws Inner reader dimension is 88mm x 88 mm (3.47" x 3.47") Assemble reader outer dimension is 90mm x 90mm (3.54” x 3.54”) Reader corner radius is 4mm (0.16”) Note: • A shielded cable is recommended to be used.
PAGE 2
Installation Remove the cover by holding the unit by the rim and pushing the reader out with your thumbs. External Use • Make sure the wire bundle to the reader has an IP rating of at least IP65 Handling • Handle the reader with care. DO NOT damage or drop unit before installation. This will void the warranty. • If the case is damaged, the reader may not be to the specified IP rating. Replace the reader if the case is damaged. Maintenance • Once installed the reader requires no maintenance.
PAGE 3
Drilling template • • • Wiring diagram 20mm (0.79”) diameter hole for wire entry 2 x 4 mm (0.16”) diameter holes for mounting screws Minimum reader dimensions are 140mm x 45 mm (5.51" x 1.77") Note: • A shielded cable is recommended to be used. The shield is connected to controller 0V reference • Maximum wiegand data cable length: 150 meters (500 feet) • Buzzer and LED are activated when buzzer and LED line go below 2.5V.
PAGE 4
Installation Remove the cover by holding the unit as shown and pulling the cover from the top as illustrated External Use • Make sure the wire bundle to the reader has an IP rating of at least IP65 Handling • Handle the reader with care. DO NOT damage or drop unit before installation. This will void the warranty. • If the case is damaged, the reader may not be to the specified IP rating. Replace the reader if the case is damaged. Maintenance • Once installed the reader requires no maintenance.