VRiSub82 Designer VRi In-Wall Subwoofer Sistemas de Altavoces VRi Subwoofer VRi VRi-Subwoofer
Contents Contenido Introduction . . . . . . . . . . . . . 2 Introducción . . . . . . . . . . . . . 2 Thank you! . . . . . . . . . . . . . . 3 ¡Gracias! . . . . . . . . . . . . . . . . 3 Specifications . . . . . . . . . . . . 3 Table des matières Inhalt Introduction Einführung ............2 .............2 Merci ! . . . . . . . . . . . . . . . . . 3 Vielen Dank! Especificaciones . . . . . . . . . . 3 Spécifications . . . . . . . . . . . . 3 Technische Daten . . . . . . . . .
Thank you! ¡Gracias! Merci ! Vielen Dank! Thank you for selecting the Boston Acoustics VRi in-wall subwoofer. Your subwoofer has been designed to deliver years of stunning audio performance. Please keep your manual in a safe place in case you need to refer to it later. Even professional installers who have experience with in-wall speakers should read the Installation Tips, as they contain VRi Subwoofer specific information. Enjoy your new VRi Subwoofer.
Installation Tips It is the nature of low-frequency energy (bass) to cause objects to vibrate. Care should be taken in planning the installation of an inwall subwoofer to minimize the risk of room vibration and noise. Some bass energy will be heard and felt in the room behind the installation. The following installation tips will help in planning your installation. Location Hazards Do not locate the subwoofer in wall cavities that contain ducts or grilles.
Installation Tips (cont.) Consejos para el montaje (cont.) Conseils d’installation (suite) Tipps zur Installation (Forts.) Wall Dampening Amortiguación del muro Amortissement du mur Wanddämpfung Performance of your VRi Subwoofer can be enhanced if the wall cavity is filled with standard fiberglass insulation. If there is already insulation and it has a paper backing facing the speaker, remove the backing in the area behind the speaker. (Consult local building codes for compliance.
Installation Tips (cont.) Consejos para el montaje (cont.) Conseils d’installation (suite) Required Clearances Espacios libres necesarios Dégagement requis Behind the mounting surface there must be 11/2-inches of clearance on either of the long sides. [see diagram below] Detrás de la superficie de montaje deben existir unos 4 cm libres a lo largo de las dimensiones largas. Prévoyez un dégagement de 4 cm derrière la surface de montage de chacun des côtés longitudinaux. Tipps zur Installation (Forts.
Installation Instructions Instrucciones de montaje Instructions d’installation Installationsanweisungen WARNING AVISO AVERTISSEMENT ACHTUNG Apague siempre el amplificador SA1 cuando conecte subwoofers, altavoces o cualquier otro componente al sistema. El VRiSub82 debe usarse únicamente con el amplificador Boston Acoustics SA1. Débranchez toujours l’amplificateur SA1 avant de connecter le subwoofer, les enceintes ou tout autre composant du système.
Installation Instructions (cont.) Instrucciones de montaje (cont.) Instructions d’installation (suite) Installationsanweisungen (Forts.) All Installations Para todas las instalaciones Toutes installations Alle Installationen 1. Strip 1/2-inch of insulation from the wire and twist the wire strands together. The VRi Subwoofer jack will accept either bare wire up to 12-gauge or single banana plugs. 2. Connect the wire to the subwoofer. 3. Slide the subwoofer into the cutout as shown.
Painting Pintura Peinture The Subwoofer Frame El marco del altavoz Armature du subwoofer The subwoofer may be painted before or after it is installed. It is already primed. 1. Insert the supplied paint mask into the frame of the subwoofer. [See diagram below.] 2. Paint the frame. If you are using spray paint, apply two light coats. If you are applying paint with a brush or roller, thin the paint and apply two very light coats. This helps prevent excessive paint buildup or “runs” on the frame. 3.
Listening Levels Power Handling Niveles de sonido Manejo de Potencia Réglage de la puissance et du niveau d’écoute The SA1 Power Amplifier is designed to be the perfect companion to the VRiSub82. Care should be taken in setting the crossover frequency and volume level so that you operate the system in a way that does not produce distortion. Please read the SA1 Power Amplifier manual for information on setting the levels. If you hear a harsh or distorted sound, turn down the volume.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state. Esta garantía otorga al comprador derechos legales específicos a los que se suman otros derechos que varían según el país de residencia. If Service Seems Necessary Si necesita la ayuda del servicio técnico Cette garantie est annulée en cas de retrait ou de dégradation du numéro de série.
300 Jubilee Drive Peabody, MA 01960 USA 978.538.5000 www.bostonacoustics.com Boston and Boston Acoustics are registered trademarks of Boston Acoustics, Inc. DCD is a trademark of Boston Acoustics, Inc. Specifications are subject to change without notice. © 2001 Boston Acoustics, Inc.