BossPac WASP™ NEST4 SMART RECEIVER AND GATEWAY USER MANUAL VERSION 1.
WASP™ is a registered trademark owned by BossPac Engineering & Technology WASP™ is a PATENT PENDING technology owned by BossPac Engineering & Technology BossPac Engineering & Technology 1450 – 28 Street NE Bay 8, Calgary, Alberta, Canada T2A 7W6 Phone: (403) 216-1226 Fax: (403) 216-5557 E-Mail: info@bosspac.com Visit our website for more information www.bosspac.
WASP™ NEST4 Smart Receiver and Gateway Operations Manual WARNING READ THIS MANUAL BEFORE OPERATING THIS DEVICE. MISE EN GARDE LISEZ LE MANUEL AVANT UTILISATER WARNING TO PREVENT EQUIPMENT FAILURE, AND/OR DAMAGE, AND/OR PERSONAL INJURY, REGULAR CALIBRATION AND INSPECTION OF THIS DEVICE IS REQUIRED. MISE EN GARDE POUR PRЀVENIR LE DOMMAGE À L’EQUIPMENT, ET/AU AUX PERSON, LA CÀLIBRATION ET L’INSPECTION REGULIER EST ŔEQUIS.
WASP™ NEST4 Smart Receiver and Gateway Operations Manual WARNING - EXPLOSION HAZARD SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS 1, DIVISION 2. AVERTISSEMENT – RISQUE D’EXPLOSION LA SUBSTITUTION DECOMPOSANTS RENDRE CE MATÉRIEL INACCEPTABLE POUR LES EMPLACEMENTS DE CLASSE 1, DIVISION 2 WARNING - EXPLOSION HAZARD DO NOT RECONNECT POWER IN A HAZARDOUS ENVIRONMENT. AVERTISSEMENT - RISQUE D’EXPLOSION NE PAS BRANCHEZ LA PRISE DANS UN ENVIRONMENT FLAMMABLE.
WASP™ NEST4 Smart Receiver and Gateway Operations Manual Table of Contents 1. Introduction ......................................................................................................................... 5 1.1 NEST Receiver Introduction ............................................................................................ 5 2. Installation........................................................................................................................... 5 2.
WASP™ NEST4 Smart Receiver and Gateway Operations Manual 3.2.3.2 Retrieving the Logs ................................................................................................15 3.2.3.3 Formatting the microSD Card .................................................................................15 3.2.3.4 microSD Card Specifications ..................................................................................15 3.2.4 Sensor Lists ....................................................................
WASP™ NEST4 Smart Receiver and Gateway Operations Manual 1. Introduction 1.1 NEST Receiver Introduction This Operations Manual provides basic information on how to operate WASP™Nest Smart Receiver and Gateway. This manual covers the following topics: the Installation of WASP™NEST Wiring of WASP™NEST Configuring of Individual WASP™Sensors System Information and Settings of WASP™NEST Maintenance of WASP™NEST 2. Installation 2.
WASP™ NEST4 Smart Receiver and Gateway Operations Manual The technician must ensure proper mounting of antenna to meet certification requirements of installation site. To attach the antenna, carefully screw the antenna cable to the SMA connection at the base of the BossPac NEST™ Receiver Gateway. See photo below. Attach antenna to opposite end of cable, (N type connector). 2.3.3 Attaching the LTE Antenna Figure 1: Antenna Connections WARNING – EXPLOSION HAZARD.
WASP™ NEST4 Smart Receiver and Gateway Operations Manual 3. Interface The touch screen interface on the BossPac NEST™ displays important current information throughout all its screens. The name of the current screen is displayed at the top center. The current time and date are displayed at the bottom right. Current critical error count and warning count are displayed in the bottom left of the interface.
WASP™ NEST4 Smart Receiver and Gateway Operations Manual 3.1 System Status Screens When activating the BossPac WASP™ system for the first time the BossPac NEST receiver will automatically detect all sensor pucks within the working radius (assuming battery modules are attached to the sensors). The default screen, when turning on the BossPac NEST™ receiver or waking the screen from sleep mode, is the SYSTEM STATUS screen.
WASP™ NEST4 Smart Receiver and Gateway Operations Manual 3.2 Main Menu The NEST system information, sensor settings, configuration area, and log options are accessed through the MAIN MENU tab of the SYSTEM STATUS default screen. Tapping MAIN MENU will bring up a list of options. Tap the UP/DOWN arrows to scroll through the available options. Choose SELECT to access the desired high-lighted option. Tap SYSTEM STATUS to return to the default startup screen. 3.2.
WASP™ NEST4 Smart Receiver and Gateway Operations Manual 3.2.2 System Settings To input or modify settings you will need to access the SYSTEM SETTINGS from the MAIN MENU screen. Use the UP/DOWN arrows to highlight the SYSTEM SETTINGS option and tap SELECT. The SYSTEM SETTINGS screen will be displayed with several options that can be configured or modified. 3.2.2.
WASP™ NEST4 Smart Receiver and Gateway Operations Manual 3.2.2.2 Set Time/Date To set the time and date on the NEST select the SET TIME/DATE option from the SYSTEM SETTINGS screen. Set the time using the UP / DOWN arrows to change the numeric value of the hour character. Use the LEFT / RIGHT arrows to move the cursor to the minute character position. Once the time has been entered, tap SET DATE and use the arrows to input the correct date.
WASP™ NEST4 Smart Receiver and Gateway Operations Manual 3.2.2.4.1 RTU Address Configure the RTU ADDRESS of the receiver by using the arrow keys to navigate and input the digits. MODBUS SET> ADDRESS CANCEL BACK RTU ADDR 001 OK 21'C CRI=4 WRN=1 13:46 NOV 24/10 3.2.2.4.2 BAUD Rate Configure the BAUD RATE of the receiver to either 9600, 14400, 19200 or 38400 by using the arrows on the right of the screen and choosing SELECT. 3.2.2.4.
WASP™ NEST4 Smart Receiver and Gateway Operations Manual 3.2.2.6 Set Velocity Units You can set the units of velocity to either mm/s or IPS (inch-per-second) by selecting SET VEL UNITS from the SYSTEM SETTINGS menu. Simply choose the unit of measurement and press SELECT.
WASP™ NEST4 Smart Receiver and Gateway Operations Manual 3.2.2.7 Set Pressure Units You can set the units of pressure to either BAR or PSI by selecting SET PRESS UNITS from the SYSTEM SETTINGS menu. Simply choose the unit of measurement and press SELECT. 3.2.2.8 Set Level Units You can set the units to either METERS or FEET by selecting SET LEVEL UNITS from the SYSTEM SETTINGS menu. Simply choose the unit of measurement and press SELECT. 3.2.2.
WASP™ NEST4 Smart Receiver and Gateway Operations Manual 3.2.2.11 Reset System Settings The reset system settings option allows you to restore the receiver to its default setting. You can restore the receiver default setting by choosing RESET SYS SETTINGS from the SYSTEM SETTINGS menu. Once in the RESET SYS SETTINGS screen tap on OK to authorize the system setting reset. RESET SYSTEM SETTINGS RESET CANCEL SYSTEM SETTINGS 21'C CRI=4 WRN=1 13:46 NOV 24/10 3.2.
WASP™ NEST4 Smart Receiver and Gateway Operations Manual 3.2.4 Sensor Lists When first configuring or adding WASP™ Sensors to the WASP™ systems, it is necessary to “bind” the sensors to the receiver. The SENSOR LISTS will show all sensors that have been attached to the system to the system. To access SENSOR LIST: > MAIN MENU > SENSOR LISTS > SELECT. This brings up the main SENSOR LISTS screen with 3 options: FREE, BOUND, and IGNORED. FREE: Shows all available sensors within range.
WASP™ NEST4 Smart Receiver and Gateway Operations Manual To bind a sensor, scroll up/down and highlight a sensor from the FREE sensor list. Once found, tap SELECT to move to BIND/IGNORE screen. BIND will add this sensor to this receiver’s database. IGNORE will ignore the sensor allowing another receiver to pick up that sensor. This is useful in large installations where you may have overlap between the effective range of sensors and receivers.
WASP™ NEST4 Smart Receiver and Gateway Operations Manual 3.2.4.3 Adding the NEST To an Existing Network To add the NEST to an existing network. Start the Network ADD process on the NEST that has the network that you would like to add this NEST to. > MAIN MENU > NETWORK > JOIN NETWORK Enter the 6-digit numeric pass phrase used on the existing network NEST and press START. 3.2.4.
WASP™ NEST4 Smart Receiver and Gateway Operations Manual 3.2.7 Configuring Individual Sensors To configure an individual sensor, you must access that particular sensor’s SENSOR SETTINGS screen. To access this screen, follow the instructions, starting from the default SYSTEM STATUS screen. First tap the bottom right SENSOR STATUS section of the default screen. This will take you to the sensor status grid screen. From this screen choose the sensor you would like to configure, (EXHA 01 for example).
WASP™ NEST4 Smart Receiver and Gateway Operations Manual This SETTINGS screen allows the user to modify the sensor name, update rate, choose vibration axes, and configure the warning alarm and critical alarm thresholds for the supported parameters. To set an individual parameter scroll the UP/DOWN arrows to the desired setting, or by tapping either the top or bottom part of the screen. Press SELECT when the desired option is highlighted. 3.2.7.
WASP™ NEST4 Smart Receiver and Gateway Operations Manual 3.2.7.3 Setting Sensor Vibration Axes The sensors can be individually configured to measure all three vibration axes (XYZ) combined, a combination of, or independently. To set the preferred option, highlight VIB AXES from the sensor SETTINGS screen and tap SELECT. Use the arrow keys to move cursor LEFT / RIGHT to the desired character position. Use the UP / DOWN arrows to toggle between 1 (enabled) or 0 (ignore).
WASP™ NEST4 Smart Receiver and Gateway Operations Manual 3.2.7.6 Setting Velocity Warning and Critical Alarm Thresholds To set the desired velocity warning and critical alarm thresholds for each individual sensor, select the desired option from the SENSOR SETTINGS screen, HI VEL / HI-HI VEL / LO VEL / LO-LO VEL The bottom left quadrant of the screen will display the current setting (in mm/s) or DISABLED if there is no current threshold setting.
WASP™ NEST4 Smart Receiver and Gateway Operations Manual 3.2.7.8 Setting Temperature Multiplier Factor To change the default setting highlight the parameter and modify the PERCENT factor using the UP/DOWN and LEFT/RIGHT arrows. Tap OK to save. 3.2.7.10 Temperature Calibration To set from the settings screen, scroll to, and select TEMP CALIBRATION to calibrate the sensor temperature reading to a reference reading.
WASP™ NEST4 Smart Receiver and Gateway Operations Manual 4. Maintenance 4.1 Rear Cover The rear cover of the NEST receiver should remain in place during operation. Do not remove except to access the NEST circuit board when necessary. Replace rear cover upon completion of task. 4.2 Replacing Batteries The BossPac NEST™ Receiver uses a 3V Lithium Battery to maintain clock and memory function. After several years of use the battery may need to be replaced. Use a standard CR2032 Lithium Coin Cell.
WASP™ NEST4 Smart Receiver and Gateway Operations Manual FCC & IC Statements FCC Class B Part 15 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by BossPac Engineering Technology Inc.
