DN-2_e1.
DN-2_e1.fm 2 ページ 2006年12月8日 金曜日 午後1時44分 Thank you, and congratulations on your choice of the BOSS DN-2 Dyna Drive. Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet). These sections provide important information concerning the proper operation of the unit.
DN-2_e1.fm 3 ページ 2006年12月8日 金曜日 午後1時44分 Main Features ● The DN-2 is an overdrive that changes the tone in response to the force of picking and the volume control on the guitar. ● Transforms the sound into one where reverberating strings retain their sharpness even if the guitar's volume is turned down. ● By simply turning the DRIVE knob, you get broad-ranging control over the depth of distortion.
DN-2_e1.fm 4 ページ 2006年12月8日 金曜日 午後1時44分 Panel Descriptions 1. AC Adaptor Jack fig.01 1 2 This jack accepts the connection of an AC adaptor (optionally available BOSS PSA-series). By using an AC adaptor, you can play without being concerned about how much battery power you have left. DRIVE 3 4 5 4 6 * Use only the specified AC adaptor (PSAseries), and make sure the line voltage at the installation matches the input voltage specified on the AC adaptor's body.
DN-2_e1.fm 5 ページ 2006年12月8日 金曜日 午後1時44分 Panel Descriptions line voltage be interrupted due to a power blackout or power cord disconnection. 2. CHECK Indicator This indicator shows whether the effect is on or off, and also doubles as the battery check indicator. The indicator lights when the effect is on. * If you're powering the unit with a battery and the CHECK indicator goes dim—or doesn't light at all—when you try to turn the effect on, the battery is near depletion and should be replaced.
DN-2_e1.fm 6 ページ 2006年12月8日 金曜日 午後1時44分 Panel Descriptions 6. INPUT Jack 7. LEVEL Knob This jack accepts signals coming from a guitar or other musical instrument, or another effects unit. * The INPUT jack doubles as power switch. Power to the unit is turned on when you plug into the INPUT jack; the power is turned off when the cable is unplugged. When not using the effects unit, be sure to disconnect the plug from the INPUT jack. This adjusts the volume of the effect sound.
DN-2_e1.fm 7 ページ 2006年12月8日 金曜日 午後1時44分 Connections * Inserting a connecting plug into the INPUT jack turns on the power to the unit. * Raise the amp volume only after turning on the power to all connected devices. * The use of an AC adaptor is recommended as the unit’s power consumption is relatively high. Should you prefer to use a battery, please use the alkaline type.
DN-2_e1.fm 8 ページ 2006年12月8日 金曜日 午後1時44分 Connections fig.03 AC Adaptor BOSS PSA-series (sold separately) OUT 9V DC/200 mA Electric Guitar DRIVE Guitar Amp * This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will operate normally.
DN-2_e1.fm 9 ページ 2006年12月8日 金曜日 午後1時44分 Operating the Unit fig.04 fig.05 DRIVE 1. After you have made the necessary connections (p. 7, 8), set the panel knobs as shown in the illustration. DRIVE 2. Depress the pedal switch to turn the effect on. (The CHECK indicator lights when the effect is on.) 3. Adjust the amount of overdrive with the DRIVE knob.
DN-2_e1.fm 10 ページ 2006年12月8日 金曜日 午後1時44分 Operating the Unit fig.06 fig.07 DRIVE 4. Adjust the tone with the TONE knob. DRIVE 5. Adjust the output volume with the LEVEL knob. Normally, you should adjust the LEVEL knob so there's no difference in the volume when switching the effect on and off.
DN-2_e1.fm 11 ページ 2006年12月8日 金曜日 午後1時44分 Changing the Battery When the indicator goes dim or no longer lights while the effect is on, it means that the battery is nearly dead and must be replaced. Replace the battery following the steps below. * The use of an AC adaptor is recommended as the unit’s power consumption is relatively high. Should you prefer to use a battery, please use the alkaline type. fig.
DN-2_e1.fm 12 ページ 2006年12月8日 金曜日 午後1時44分 Troubleshooting The power won’t come on / the CHECK indicator doesn’t light ● Is the specified adaptor (PSA-series, sold separately) properly connected? Check the AC adaptor connection (p. 7, 8). * Never use any AC adapter other than one specified for use with the DN-2. * A cable must be connected to the INPUT jack to allow the effect to be turned on.
DN-2_e1.fm 13 ページ 2006年12月8日 金曜日 午後1時44分 Setting Samples DN-2 Overdrive Long Sustain for Solo fig.09-01 fig.09-03 DRIVE DRIVE Crunch Chord Play fig.09-02 fig.
DN-2_e1.fm 14 ページ 2006年12月8日 金曜日 午後1時44分 Setting Memo fig.10 fig.10 DRIVE fig.10 fig.
DN-2_e1.fm 15 ページ 2006年12月8日 金曜日 午後1時44分 Specifications DN-2: Dyna Drive Nominal Input Level........................ -20 dBu Input Impedance............................... 1 MΩ Nominal Output Level..................... -20 dBu Output Impedance ........................... 1 kΩ Recommended Load Impedance.... 10 kΩ or greater Controls.............................................. Pedal switch, LEVEL knob, TONE knob, DRIVE knob Indicator.............................................
DN-2_e1.fm 16 ページ 2006年12月8日 金曜日 午後1時44分 Specifications Dimensions ........................................ 73 (W) x 129 (D) x 59 (H) mm 2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches Weight ................................................ 440 g/ 1 lb (including battery) Accessories.........................................
DN-2_e1.
DN-2_e1.
DN-2_e1.fm 19 ページ 2006年12月8日 金曜日 午後1時44分 For EU Countries This product complies with the requirements of European Directive 89/336/EEC. For the USA FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
DN-2_e1.