User Manual

ManualsBrandsBose ManualsElectronics802.11b/g and Bluetooth LE Wireless Module

2.4GHz RF Modular Transceiver System

Installation manual (draft v1)

1. Description

This document describes an RF transceiver module PCB having two independent

radio transceivers. One radio complies to IEEE 802.11b/g protocols and the other to

the Bluetooth Low Energy specification. The module provided on-board power

regulation and full shielding for the radio transceivers.

The module consists of 2 separate circuits :

1) A 2.4GHz Wi-Fi RF transceiver IC and two PIF etch antennas.

2) A 2.4GHz Bluetooth Low Energy transceiver IC and one PIF etch antennas.

3. Cautions:

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause

undesired operation.

Any changes or modifications not expressly approved by Bose Corporation could void the

user's authority to operate this equipment.

WARNING! This module is to be installed only by Bose Corporation in its end products,

and shall not be marketed to any other party.

This RF Module has been certified for integration into products without further

certification. However, Bose Corporation is still responsible for testing its end products

for any additional compliance requirements required with this module installed (such as

digital device emissions, PC peripheral requirements, etc.).

Summary of content (6 pages)

PAGE 1
2.4GHz RF Modular Transceiver System Installation manual (draft v1) 1. Description This document describes an RF transceiver module PCB having two independent radio transceivers. One radio complies to IEEE 802.11b/g protocols and the other to the Bluetooth Low Energy specification. The module provided on-board power regulation and full shielding for the radio transceivers. 2. The module consists of 2 separate circuits : 1) A 2.4GHz Wi-Fi RF transceiver IC and two PIF etch antennas. 2) A 2.
PAGE 2
End Product Labeling This module is labeled with its own FCC ID and IC Certification Number. If the label is not visible when the module is installed inside another device, then the outside of the device into which this module is installed must also display a label referring to the enclosed module.
PAGE 3
approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. 4. Markings 4.1 This module shall be identified with the following ID numbers on the radio shields. FCC ID : A94412568 IC : 3232A-412568 4.
PAGE 4
5. Connections The following tables describe the connections to the module made via the four connectors.
PAGE 5
J1202 Pin # 12 11 10 9 8 7 6 5 4 3 2 1 Group Name GND LED LED OLED Power IR_RECEIVER Anode + Power OLED Control OLED Control OLED Control OLED Control OLED Control GND Group Name GND LED0 LED1 OLED_17V UART0_RXD/IR_IN LED_5V DISPCEN DISPRESN DISPDCN SP1_SCLK SPI2_DO GND 6. General Electrical specifications 6.1 Power supply 5.0V +/- 5% 6.2 Power consumption <5 Watts 6.3 Operational Temperature 0 ~ 45 C (non-condensing) 7. 2.
PAGE 6
7.2 2.4GHz 802.11b/g RF Transceiver The transceiver uses a proprietary and confidential chip set from SMSC corporation for control and implementation of the IEEE 802.11b/g radio. A DM870 control chip implements the transmission protocol and feeds I-Q information to the company’s T6201C RF transceiver. For transmit, the RF path includes a power amplifier SST12LP15A from Microchip. The module shall use the following settings: 7.2.1 RF output power: +11dBm typical (measured at CON4) 7.2.