AMC UL2 Housing | en 1 Included Parts The metal housing inlcudes the following components: Figure 1 Parts of the housing The accessories kit includes the following cables. Install these cables as described in Section Connection of the Devices, page 4. Bosch Security Systems Assembly Instruction F.01U.029.481 | V.2 | 2006.
en | AMC UL2 Housing Figure 2 Accessories kit content Content of the accessories kit: A = Pre-assembled cable to connect the AMC to the power supply B = Pre-assembled cable to connect the batteries to the UPS (uninterruptable power supply) which is included in the power supply C = Cable using 24 V mode D = Grounding cable for the cover E = Cable ties to secure the pre-assembled cable G = Pre-assembled cable with temperature sensor H = Three screw anchors S8 and wood screws M6 x 50 J = Bracket for cabl
AMC UL2 Housing | en 3 Mounting the Housing Open the housing cover lock with the provided key and remove the hood from the wall mounted frame. Mount the metal housing at the desired position with the screw anchors provided with the enclosure. Use the screws (position H of the accessories kit) at the points to mount the housing against the wall. Figure 3 Demensions of the housing Bosch Security Systems Assembly Instruction F.01U.029.481 | V.2 | 2006.
en | AMC UL2 Housing Connection of the Devices Figure 4 Connection of the devices F.01U.029.481 | V.2 | 2006.
AMC UL2 Housing | en 5 NOTE! i The following steps describe connecting the batteries in 24 V mode. For information on 12 V mode connections, refer to Section 12 V Mode Variations, page 8. 1. Mount the AMC on the rail (item 2 in Figure 1) and left aside the power supply. The second mounting rail is planned for the extension board. 2. Put the batteries on the bottom of the housing and secure them beneath the battery clips (item 7 in Figure 1). 3.
en | AMC UL2 Housing b. Route the cable across the temperature sensor bracket 6 so that the temperature sensor G2 hangs approximitely 5 cm (2 in.) above the batteries. 7. Pre-assembled cable set 12: a. Connect the 2-pin plug 14 on the interface AC of the power supply. 8. Pre-assembled cable 5: a. Connect the loose ends of the cover tamper switch to the 2-pin screw connector on the top of the AMC. Position the cable in the space between the housing and the mounting rail.
AMC UL2 Housing | en b. 7 Additional to the data lines (pin 3 and 6) connect the power supply (pin 1 and 2), too. NOTE! i Connect the readers and other peripheral devices as described in the AMC Installation Manual (P/N: F01U.028.713). Route the device cables through the knock-outs in the top an right side wall of the housing, or through the rear of the housing. 11. Cable D: If this cable is not pre-installed on grounding point 1, use the cable D from the accessories kit. a.
en | AMC UL2 Housing 12 V Mode Variations Figure 5.1 + 2 12 V mode with one and two batteries The 12 V mode can be configured using one or two batteries. For a one-battery installation, refer to Figure 5.1, and perform the following procedure: 1. Connect B1 to the power supply position labbeled BAT. 2. Connect B2a (black) to the battery’s - terminal, and B2b (red) to the battery’s + terminal. 3. Connectors B3a and B3b remain unused - fix them with the bracket J.
AMC UL2 Housing 3. | en Connect B3a (black) to the second battery’s 9 - terminal, and B3b (red) to the second battery’s + terminal. NOTE! To switch the power supply between 12 V or 24 V modes, disconnect the input voltage and set the switch as shown in the figure below. i Bosch Security Systems Assembly Instruction F.01U.029.481 | V.2 | 2006.
en | F.01U.029.481 | V.2 | 2006.
AMC UL2 Housing Bosch Security Systems | en 11 Assembly Instruction F.01U.029.481 | V.2 | 2006.
en | F.01U.029.481 | V.2 | 2006.