AMC2 ENC3 Enclosure AEC-AMC2-ENC3 | AEC-AMC2-ENC3Z en Installation Manual
AMC2 ENC3 Enclosure Table of Contents | en 3 Table of Contents 1 Copyright Notice 4 2 Safety and Warranty 5 2.1 Important safety notes 5 2.2 FCC information 6 3 Short Information 7 4 System Overview 8 4.1 Parts of the enclosure 8 4.2 Dimensions of the enclosure 9 5 Planning the Mounting Location 10 6 Mounting the Enclosure 11 7 Connecting the Devices 12 7.1 Connecting the devices in AEC-AMC2-ENC3 12 Robert Bosch (SEA) Pte Ltd Installation Manual F.01U.269.165 | V1.0.
1 en | Copyright Notice AMC2 ENC3 Enclosure Copyright Notice All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of BOSCH SECURITY SYSTEMS. This manual is provided pursuant to a license agreement containing restrictions on their use.
AMC2 ENC3 Enclosure Safety and Warranty | en 2 Safety and Warranty 2.1 Important safety notes 1. 5 Read, Follow, and Retain Instructions – All safety and operating instructions must be read and followed properly before putting the unit into operation. Retain instructions for future reference. 2. Consider all Warnings – Adhere to all warnings on the unit and in the operating instructions. 3. Accessories – Use only accessories recommended by the manufacturer or those sold with the product.
2.2 en | Safety and Warranty AMC2 ENC3 Enclosure FCC information NOTICE! This device complies with Part 15 FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation. F.01U.269.165 | V1.0.0 | 2012.
AMC2 ENC3 Enclosure 3 Short Information | en 7 Short Information This guide is designed for the configurers who need to plan and install the enclosure within the premise of the building. Mounting the enclosure involves drilling of the walls. Therefore, recommendations and instructions are included to aid in the planning and installation of the enclosure. Robert Bosch (SEA) Pte Ltd Installation Manual F.01U.269.165 | V1.0.0 | 2012.
4 en | System Overview AMC2 ENC3 Enclosure System Overview The enclosure has been produced in accordance with strict guidelines, and is used for securely mounting and housing the AMC and a power supply. 4.1 Parts of the enclosure The panel casing (without the cover) includes the following parts. Figure 4.1 Parts of the enclosure Number Part 1 Mounting rail for AMC 2 Cable knockouts for reader and signal cables 3 Cover tamper switch 4 Battery clips F.01U.269.165 | V1.0.0 | 2012.
AMC2 ENC3 Enclosure 4.2 System Overview | en 9 Dimensions of the enclosure Dimensions of the panel casing are as of below: Figure 4.2 Dimensions of the enclosure Dimension (W x H x D) 400 mm x 400 mm x 96 mm (15.75 in x 15.75 in x 3.7 in) Robert Bosch (SEA) Pte Ltd Installation Manual F.01U.269.165 | V1.0.0 | 2012.
5 en | Planning the Mounting Location AMC2 ENC3 Enclosure Planning the Mounting Location Before mounting the enclosure, proper planning ensures that you encounter less issues. Obtain the mounting location details before installing the enclosure. The mounting location for the enclosure should provide: 1. protection from unauthorized access 2. protection from accidental damage 3. (ideally) an uninterruptable power supply (UPS) 4. protection from electrical interference 5.
AMC2 ENC3 Enclosure 6 Mounting the Enclosure | en 11 Mounting the Enclosure This section addresses the mounting procedure of the enclosure. For mounting, always use hardware and materials appropriate to the nature of the surface upon which the enclosure is to be mounted. The following instructions describe the basic steps to mount the enclosure on a concrete wall. WARNING! Always use hardware and materials appropriate to the nature of the mounting surface. If in doubt, consult a certified technician. 1.
7 en | Connecting the Devices AMC2 ENC3 Enclosure Connecting the Devices This section provides information on connecting the various devices within the enclosure. 7.1 Connecting the devices in AEC-AMC2-ENC3 1. Mount the AMC on the rail (item 1 in Figure 4.1). 2. Place the battery on the bottom of the panel, and secure them beneath the battery clips (item 4 in Figure 4.1). 3. Connect the 2-pin screw connector of the cover tamper switch to the tamper contact at the top of the AMC.
AMC2 ENC3 Enclosure Connecting the Devices | en 4. 13 Connect the 7-pin screw connector of the power supply unit (PSU) to the power supply contact at the bottom of the AMC. Position the cable in the space between the battery and the AMC panel. Figure 7.2 Connecting the power supply unit 5. Robert Bosch (SEA) Pte Ltd Connect and turn on the main AC supply. Installation Manual F.01U.269.165 | V1.0.0 | 2012.
en | Connecting the Devices F.01U.269.165 | V1.0.0 | 2012.
Robert Bosch (SEA) Pte Ltd 11 Bishan Street 21 573943 Singapore Singapore www.boschsecurity.