User's Manual

ManualsBrandsBosch Security Systems ManualsElectronicsBelt Pack Transmitter

Table Of Contents

Preliminary Users Manual

Preliminary Users Manual

Electro-Voice Model REV-WT Wireless Microphone Transmitter

The Electro-Voice (Ev) REV-WT is a Professional Grade Wireless Beltpack

Transmitter operating in the UHF frequency range. The REV-WT combines

frequency agility and ease of use like no other. The transmitter operates

within a 24 MHz wide segment in 25 KHz steps.

The high quality audio circuitry and advanced Radio Frequency (RF) signal

processing offer broadcast quality signal-to-noise ratio and audio clarity.

The RF range of the REV-WT communicating to a receiver may be up to

150 meters (492 ft).

System features include:

• Durable Painted Metal Case.

• TA-4F Audio Connector.

• Permanent Flash Memory for frequency/setting storage.

• On-Loc prevents accidental power off (when set).

• LCD Display for ease of viewing.

• Flexible quarter wave screw-on Antenna.

Quick set-up:

1. With the Power Switch on the transmitter OFF, install fresh batteries into

the transmitter.

2. To prevent feedback or unintentional noise, mute the audio

mixer/amplifier or other device during set-up adjustments.

Place the transmitter Power Switch to the ON position.

3. The Battery light near the Off/On switch will flash once and then go off.

If the light does not flash, a bad battery is the most likely cause.

The display will also come on briefly displaying the current frequency

group and channel and the battery level. Note: Anytime Power is

removed and turned back on, the GP/CH/Bat screen will be displayed.

Summary of content (4 pages)

PAGE 1
Preliminary Users Manual Electro-Voice Model REV-WT Wireless Microphone Transmitter The Electro-Voice (Ev) REV-WT is a Professional Grade Wireless Beltpack Transmitter operating in the UHF frequency range. The REV-WT combines frequency agility and ease of use like no other. The transmitter operates within a 24 MHz wide segment in 25 KHz steps. The high quality audio circuitry and advanced Radio Frequency (RF) signal processing offer broadcast quality signal-to-noise ratio and audio clarity.
PAGE 2
REV-WT Users Manual Page 2 Quick set cont’d. 4. If the Group and Channel match the desired receiver group and channel, proceed to Step 9. If not, proceed to Step 5. 5. To select a different GP/CH, press SET one time. The Group will start flashing. Use the up and down arrows to change the group number. Press the SET button to save the Group. After setting the Group, The Channel number will start flashing. Use the up/down arrows to change the Channel number. Press SET and the channel is now saved. 6.
PAGE 3
REV-WT Users Manual Page 3 Quick set cont’d. 7. Press the Menu button one time to advance to the next screen function. pressing the button once each time allows the user to scroll through the functions or change a function. The next screen is the audio (microphone/instrument) level (attenuator) screen. Setting the levels correctly depends on the microphone or instrument used and the person using the microphone. Setting the attenuator to “0”db is the same as setting a control to maximum gain.
PAGE 4
REV-WT Users Manual Specifications: Page 4 RF Frequency range……………………614.0 to 698.0 MHz. RF Channel Step……………………….25 KHz RF Power………………………………Norm, 5 mW, High, 50 mW. Modulation…………………………….FM, 40 KHz nominal. Audio Frequency Response……………80-15000 Hz +/- 2 dB. Audio attenuator Range………………..42 dB. Microphones, Electret or Dynamic…… Electret bias provided. Antenna………………………………..Quarter Wave Flexible. Battery Life (Alkaline)………………... 8-10 Hours Typical. Final Collector Voltage (High Power)... 4.