DCN Next Generation 2.
DCN Next Generation 2.40 Release Notes Table of contents 1 2 3 4 5 6 7 8 9 10 11 Introduction ................................................................ 4 Release 2.40 ............................................................... 5 Release 2.12 ............................................................... 6 Release 2.10 ............................................................... 7 Release 2.01 ............................................................... 8 Release 2.00 ....................
DCN Next Generation 2.40 Release Notes 1 Introduction This document contains information, which was not available during the creation of the manuals. Please read all manuals.
DCN Next Generation 2.40 Release Notes en | 5 2.3 2 Release 2.40 Known limitations 2.3.1 2.1.1 Release March 8th 2007 Adding system units to the optical ring when powered on. In case system units are added to the optical ring when the system is powered on, unexpected behavior can occur. Only connect units to the optical network when all units are powered off. 2.1.2 2.3.2 2.
DCN Next Generation 2.40 Release Notes en | 6 3.3 3 Release 2.12 Known limitations 3.3.1 3.1 Microphone will be reset to default after de-init. When a de-init is activated at the CCU the microphone is always set to microphone mode “open” with 2 active microphones. General 3.1.1 Release February 5th 2005 3.1.2 3.3.2 Use of Developers Toolkit The developers toolkit provided on this CD-ROM can only be used with Windows 2000.
DCN Next Generation 2.40 Release Notes en | 7 4.3 4 Release 2.10 Known limitations 4.3.1 4.1 Microphone will be reset to default after de-init. When a de-init is activated at the CCU the microphone is always set to microphone mode “open” with 2 active microphones. General 4.1.1 Release Date November 8th 2005 4.1.2 4.3.2 Use of Developers Toolkit The developers toolkit provided on this CD-ROM can only be used with Windows 2000.
DCN Next Generation 2.40 Release Notes en | 8 5.3 5 Release 2.01 Known limitations 5.3.1 5.1 General 5.1.1 Release Date May 30th 2005 5.1.2 Firmware/FPGA versions Product DCN-CCU DCN-CON DCN-CONCS DCN-CONFF DCN-CONCM DCN-DDB DCN-DDI DCN-FCS DCN-IDESK LBB 4402/00 FPGA 1.06 1.0 SW 2.01.0989 2.00.XXXX FW 3.10.1716 -- 1.0 1.00.XXXX -- -1.0 1.0 1.3 -- 1.3.XXXX --1.10.XXXX 2.01.0989 ----3.10.1716 5.1.
DCN Next Generation 2.40 Release Notes en | 9 6.3 6 Release 2.00 Known limitations 6.3.1 6.1 General 6.1.1 Release Date March 3th 2005 6.1.2 Firmware/FPGA versions Product DCN-CCU DCN-CON DCN-CONCS DCN-CONFF DCN-CONCM DCN-DDB DCN-DDI DCN-FCS DCN-IDESK LBB 4402/00 FPGA 1.06 1.0 SW 2.00.0920 2.00.XXXX FW 3.10.1667 -- 1.0 1.00.XXXX -- -1.0 1.0 1.3 -- 1.3.XXXX --1.10.XXXX 2.00.0920 ----3.10.1667 6.1.
DCN Next Generation 2.40 Release Notes See the Installation and User Instruction for how to set the auto restore function. 7 Release 1.12 7.1 If it is important that you can connect and replace each unit during operation, without the above described reset behavior: power the units with the LBB 4106 Extension Power Supply Unit. The LBB 4106 Extension Power Supply Unit is less prone to the inrush current. General 7.1.1 Release Date December 10th 2004 7.1.
DCN Next Generation 2.40 Release Notes See the Installation and User Instruction for how to set the auto restore function. 8 Release 1.11 8.1 If it is important that you can connect and replace each unit during operation, without the above described reset behavior: power the units with the LBB 4106 Extension Power Supply Unit. The LBB 4106 Extension Power Supply Unit is less prone to the inrush current. General 8.1.1 Release Date July 23rd 2004 8.1.
DCN Next Generation 2.40 Release Notes en | 12 9 Release 1.10 the auto restore function of the channel selector. See the Installation and User Instruction for how to set the auto restore function. 9.1 If it is important that you can connect and replace each unit during operation, without the above described reset behavior: power the units with the LBB 4106 Extension Power Supply Unit. The LBB 4106 Extension Power Supply Unit is less prone to the inrush current. General 9.1.
DCN Next Generation 2.40 Release Notes If it is important that the channel selectors are not reset to default in above described situation: use the auto restore function of the channel selector. See the Installation and User Instruction for how to set the auto restore function. 10 Release 1.00 10.1 General If it is important that you can connect and replace each unit during operation, without the above described reset behavior: power the units with the LBB 4106 Extension Power Supply Unit.
DCN Next Generation 2.40 Release Notes en | 14 11 History Release 2.4 Release Date 2007-03-08 2.12 2006-02-05 2.10 2005-10-10 2.01 2005-05-30 2.00 2005-03-03 1.12 1.11 2004-12-10 2004-07-23 1.10 2004-06-25 1.00 2004-06-15 Release Comments • Support for Multi CCU applications. • Bugs solved. • System bug solved: At room temperature higher than 25 degree’s system reboot may not work properly. • Concentus bug solved: Audio may contain hearable ticks.
For more information please visit www.boschsecurity.com © 2007 Bosch Security Systems B.V.