Black Max™ Amplifier X300, X450, & X600 Models Installation and Use Manual © 2005 Bogen Communications, Inc. All rights reserved.
Notice IMPORTANT Every effort was made to ensure that the information in this guide was complete and accurate at the time of printing. However, information is subject to change. Important Safety Information WARNING: To Reduce The Risk of Fire Or Electric Shock, Do Not Expose This Apparatus To Rain Or Moisture. Always follow these basic safety precautions when installing and using the unit: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Read these instructions. Keep these instructions. Heed all warnings.
Contents Page INTRODUCTION................................................................................................................1 Package Contents ........................................................................................................................................1 PANEL DESCRIPTIONS..................................................................................................2-3 Black Max Front Panel ...........................................................................
iii
Introduction Bogen's Black Max™ amplifiers deliver on what professional sound installers need most: Power and Reliability. Power With three different models (X600, X450, and X300), the Black Max series provides 2 independent channels of amplification at 600W, 450W, and 300W per channel into 70V constant voltage speaker loads safely and securely. Located on the rear of the amplifier are the Level Controls, Low-Cut Filter Switch, and pluggable input terminal strip for each amplifier channel.
Panel Descriptions Black Max Front Panel 1. Status Indicators - The Status LEDs are multi-purpose indicators, one for each channel. Green - Amplifier is on and operating normally. Amber - Amplifier is in low-power consumption Sleep Mode. Red - Amplifier has protected itself due to a fault condition. 2. Signal Indicators - These illuminate green when signal is present at the output, one for each channel. 3.
Panel Descriptions Black Max Rear Panel 1. Speaker Terminals - Connects to 70V constant voltage speaker loads. One set for each amplifier section.Accepts up to #10 AWG wire or spade lugs for speaker system connections. 2. Ground Terminal - Provides convenient access to earth ground. 3. Automatic Sleep Mode - Allows the unit to automatically put itself into a sleep mode when there has been no input activity for more than 3 minutes. In sleep mode, the amplifier’s idle power is greatly reduced.
Installation Mechanical Components 1. Rack Ears - Prior to installing the amplifier into a 19" rack, you will need to attach the rack ears. Remove and save the 6 front most cover screws on each side panel of the amplifier. Position the rack ears as shown and attach using the 6 screws. 2. Dust Filter - Insert the dust filter into the fan grille before attaching the fan grille to the amplifier.
Installation Ventilation The Black Max amplifiers were designed to be placed on a table or rack-mounted. For rack-mounted applications, the amplifiers can be stacked one on top of the other for maximum use of the rack space available without any extra, empty rack spaces between them. An open air space of at least 4" must be provided at the front air intakes of the amplifier and the rear exhaust must have at least 4" between itself and obstructions to ensure adequate cooling.
Connections Speakers 70V "Transformer-Coupled" Speakers The Black Max series was designed to drive only 70V constant voltage type speaker loads. The use of low-impedance speakers may cause the amplifier to engage its protection circuits and shut down or limit amplifier function. The speaker terminals can accept up to a #10 AWG wire or spade lug and have integral clamping plates which make wiring easier. The polarity of each set of speaker outputs (A & B) is indicated with a "+" and "-" sign.
Sequential Turn-On Sequential Turn-On Operation Black Max amplifiers contain a sequential turn-on feature that is designed to turn on a bank of Black Max amplifiers, one at a time, in sequence with approximately 1 second between each amplifier. This type of sequencing of power is necessary in large systems where the in-rush current of all the system amplifiers turning on at once would overload the AC mains supplying the system.
Operation Front Controls & Indicators Power Switch The Power Switch for the Black Max amplifier is located on the front of the unit. Press the "I" side of the switch to turn the unit ON.The amplifier will begin its power up process once turned on. If the amplifier is set up for power sequencing (see the section on power sequencing), the amplifier may not begin its power up process but rather wait in a standby state until it receives a sequence trigger.
Operation Sleep Switch The Black Max amplifier includes a sleep mode feature that greatly reduces the power consumption of the amplifier after it has been idle (no audio activity) for more than 3 minutes. Any audio activity present at the input will power up the amplifier instantaneously and noiselessly, so that there is no loss of audio. The Sleep Switch is located on the rear of the unit. The sleep feature is activated by setting the switch to the AUTO position.
Troubleshooting PROBLEM UNIT APPEARS DEAD (NO FRONT STATUS LED) SEQUENCING NOT FUNCTIONING CORRECTLY CONDITION CAUSE Rear Power Status LED is off. • Amplifier not plugged in • AC outlet dead Rear Power Status LED is amber.
Specifications Power Output* X600 X450 X300 600W /Ch @ 70V 450W / Ch @ 70V 300W / Ch @ 70V 1V/0.1V Input Sensitivity (selectable) 104 dB ref. 70V, F.P. S/N Ratio (20 kHz BW) Class of Operation Connector: H Power 15A line cord 20A line cord Input Pluggable 3-pin terminal strips Output 5-pin "touch-proof" Barrier Strip Power Bandwidth 20 Hz - 40 kHz .5% THD THD @ 1 kHz Rated Power Rated Load Impedance (per Ch.) less than .02% 11 ohms 8 ohms Frequency Response @ 1 watt 1.
50 Spring Street, Ramsey, NJ 07446, U.S.A. Tel. 201-934-8500; Fax: 201-934-9832; www.bogen.
