PCM2000 Configuration Guide 50 Spring Street, Ramsey, NJ 07446 U.S.A. Tel. 201-934-8500 / Fax 201-934-9832/ www.bogen.com Downloaded from: http://www.guardianalarms.
Contents SYS-ID SWITCH SETTINGS CHART FOR ADDITIONAL SATELLITE SYSTEMS Zone #’s S1 S2 S3 S4 1-9 0 0 0 0 1 10-18 1 0 0 0 2 19-27 0 1 0 0 3 28-36 1 1 0 0 4 37-45 0 0 1 0 5 46-54 1 0 1 0 6 55-63 0 1 1 0 7 64-72 1 1 1 0 8 73-81 0 0 0 1 9 82-90 1 0 0 1 10 91-99 0 1 0 1 Master SECTION I - APPLICATON CONFIGURATIONS...................................................................................................................................
SECTION I: APPLICATION CONFIGURATIONS RD B RD C RD A - RD COM ZONE A + ZONE C ZONE B - - + ZONE A + IN RT LOCAL BGM OUTPUT HI PWR LO PWR GLOBL BGM ZONE C ZONE B BOGEN 0 COM NC NO RLY TWO RLY ONE COM NC BGM SRC IN RT OVER RIDE TEL LINE NIGHT RING BGM SRC VOLUME TONE VOLUME S1 S2 S3 S4 S5 S6 S7 POWER TEL INT SEL PCM CPU + - - 1.5A GND ST PCM PS2 + 12VDC NO GND AUX GND EM/SC HPBGM RT IN RT OUT PA LPBGM IN RT IN RT PA + 12 VDC 1.
Clock Set Clock Sync.
FEATURE CODES AND DEFAULTS SETUP FOR CONFIGURATION 2: PAGE PORT VOX CIRCUIT - 3-ZONE - ONE-WAY PAGING - SINGLE AMPLIFIER - 25/70V AC SPEAKERS RD COM RD B RD C RD A - + - - + ZONE C ZONE B ZONE A ZONE B ZONE A + IN RT LOCAL BGM OUTPUT HI PWR LO PWR GLOBL BGM ZONE C ZONE B BOGEN 0 PCM CPU + Privacy Beep Inhibit Enable Pre-announce Tone Inhibit Beep Chime Confirmation Tone Inhibit Enable Emergency O/R Tone Inhibit Enable All-Call Inhibit Enable Dialing Time-out Inhibit Enable Trunk D
SECTION II - PROGRAMMING SYSTEM PROGRAMMING CONFIGURATION 2: PAGE PORT VOX CIRCUIT - 3-ZONE - ONE-WAY PAGING - SINGLE AMPLIFIER - 25/70V AC SPEAKERS System programming lets you set certain PCM options and tone features using the DTMF keys of a telephone. It also lets you program paging zone groups and signaling zone groups. This configuration is for Page Ports without Contact Closures.
CONFIGURATION 16: SETUP FOR CONFIGURATION 3: LOOP START TRUNK - 3-ZONE - ONE-WAY PAGING - SINGLE AMPLIFIER - 25/70V AC SPEAKERS PCM ZPM ZONE A ZONE B ZONE C RELAY DRIVER OUTPUT ZONE A ZONE B ZONE C OFF ON TALKBACK SUPRESSION DIODES LPBGM VOLUME RD COM RD B RD C RD A - + ZONE C ZONE B - - + ZONE A + IN RT LOCAL BGM OUTPUT HI PWR LO PWR GLOBL BGM ZONE C ZONE B ZONE A LPBGM VOLUME OFF ON TALKBACK POWER ZONE A ZONE B ZONE C POWER BGM OUT IN RELAY PCM ZPM BGM OUT IN ZONE A
CONFIGURATION 3: LOOP START TRUNK - 3-ZONE - ONE-WAY PAGING - SINGLE AMPLIFIER - 25/70V AC SPEAKERS CONFIGURATION 15: SINGLE AMPLIFIER BACKGROUND MUSIC LINE-LEVEL SIGNAL Single amplifier BGM operation is a programmable feature that lets the PCM2000 use the paging amplifier to provide high-power BGM to the 25/70V AC speakers when the paging system is idle.
CONFIGURATION 14: SETUP FOR CONFIGURATION 4: GROUND START TRUNK - 3-ZONE - ONE-WAY PAGING - SINGLE AMPLIFIER - 25/70V AC SPEAKERS DTMF MICROPHONE ZONE PAGING This section will describe the configuration for the use of a Shure microphone Model 885TT with DTMF dialing capabilities and the MODULINK fiveconductor coil-cord model ALM-1.
CONFIGURATION 4: GROUND START TRUNK - 3-ZONE - ONE-WAY PAGING - SINGLE AMPLIFIER - 25/70V AC SPEAKERS GND ST COM RLY TWO In this configuration, the PCM unit supplies a 48V talk battery and loop current detection from pins 3 & 4 of the TEL LINE jack on the PCMTIM module to the ground start trunk in the telephone system.There are two modes of operation for ground start trunk.
SETUP FOR CONFIGURATION 5: STATION LEVEL/CENTREX - 3-ZONE - ONE-WAY PAGING - SINGLE AMPLIFIER - 25/70V AC SPEAKERS CONFIGURATION 13: EMERGENCY VOICE ANNOUNCEMENT OVERRIDE Voice Announcement Override is a non-programmable feature that lets the caller take priority over all paging functions and make a systemwide emergency voice announcement page to all speakers. In addition to the PCM modules, this option requires a ProHold (digital announcer) and a normally open momentary switch supplied by the user.
CONFIGURATION 5: STATION LEVEL/CENTREX - 3-ZONE - ONE-WAY PAGING - SINGLE AMPLIFIER - 25/70V AC SPEAKERS GND ST RLY TWO COM NO NC RLY ONE COM NO NC BGM SRC IN RT OVER RIDE TEL LINE NIGHT RING BGM SRC VOLUME TONE VOLUME In this configuration, the PCM unit responds to a 90V AC 20Hz ringing signal in pins 3 & 4 of the TEL LINE jack on the PCMTIM module and answers after the first full ring. As soon as it answers, the default timer is started.
CONFIGURATION 12: DFT120 & TAMB WIRING DIAGRAM - LOOP START TRUNK, GROUND START TRUNK, OR STATION LEVEL RD COM RD B RD C RD A - ZONE C ZONE B - + ZONE A - + + IN RT LOCAL BGM OUTPUT HI PWR LO PWR GLOBL BGM ZONE C OUT BGM IN ZONE B ZONE A LPBGM VOLUME OFF ON TALKBACK POWER ZONE A ZONE B ZONE C PCM ZPM In this configuration, the telephone output is connected to the Bogen Telephone Access Module model TAMB; the TAMB module is connected to the Bogen Digital Feedback Terminator model
SETUP FOR CONFIGURATION 12: DFT120 & TAMB WIRING DIAGRAM - LOOP START TRUNK, GROUND START TRUNK OR STATION LEVEL CONFIGURATION 6: EXTENDED PAGING SYSTEM GND ST RLY TWO COM NO NC COM NO RLY ONE BGM SRC IN RT NC OVER RIDE TEL LINE NIGHT RING BGM SRC VOLUME TONE VOLUME As described previously, the required setup for one-way basic configuration includes: PCMTIM, PCMCPU, PCMZPM, and the power supply PCMPS2.
CONFIGURATION 11: SETUP FOR CONFIGURATION 7:TWO-WAY TALK BACK PAGING SYSTEM MICROPHONE OVERRIDE In addition to the PCM modules, setup requires a Bogen VAR1 (voice-activated relay), PRS40C (12V DC power supply) and an MBS1000 or DDU250 (desktop microphone). ZONE A ZONE B ZONE C Microphone Override is a feature that lets the system designer take priority over all paging functions and make a system-wide page to all speakers.
CONFIGURATION 7: SETUP FOR CONFIGURATION 11: MICROPHONE OVERRIDE GND ST RLY TWO COM NO NC RLY ONE COM NO NC BGM SRC IN RT OVER RIDE TEL LINE NIGHT RING BGM SRC VOLUME TONE VOLUME This configuration is essentially the same as the one-way paging system described previously.The main difference between the one-way configuration and this configuration is that the centralized high-power amplifier is connected to the PCMTBM module instead of the PCMCPU module.
CONFIGURATION 10: 6 ZONES - ONE-WAY PAGING - MIXED HIGH- AND LOW-POWER ZONES 25/70V AC OR SELF-AMPLIFIED SPEAKERS RD COM RD B RD C - RD A ZONE C ZONE B - + - + + IN RT ZONE A LOCAL BGM OUTPUT HI PWR LO PWR GLOBL BGM ZONE C ZONE B ZONE A LPBGM VOLUME High- and Low-Power Mixed System is a non-programmable feature that lets the system designer use a dedicated amplifier or self-amplified speaker per zone and at the same time use a centralized amplifier for zones requiring less than 250 wat
CONFIGURATION 8: SETUP FOR CONFIGURATION 10: 6 ZONES - ONE-WAY PAGING - MIXED HIGH- AND LOW-POWER ZONES 25/70V AC OR SELF-AMPLIFIED SPEAKERS TWO-WAY TALK BACK EXTENDED PAGING SYSTEM ZONE A ZONE C ZONE B The required setup includes: PCMTIM - 2 PCMCPU - PCMTBM - 4 PCMZPM - 2 PCMPS2 ZONE A ZONE B ZONE C This configuration is essentially the same as the two-way paging system described previously on page 17.The main difference is the addition of a satellite assembly.
SETUP FOR CONFIGURATION 9: 3-ZONE - ONE-WAY PAGING - LOW-POWER SYSTEM - DEDICATED AMPLIFIERS OR SELF-AMPLIFIED SPEAKERS CONFIGURATION 9: 3-ZONE - ONE-WAY PAGING - LOW-POWER SYSTEM - DEDICATED AMPLIFIERS OR SELF-AMPLIFIED SPEAKERS Low-Power System is a switch-selectable feature that allows the system designer to use dedicated amplifiers or self-amplified speakers on the zone outputs.
SETUP FOR CONFIGURATION 9: 3-ZONE - ONE-WAY PAGING - LOW-POWER SYSTEM - DEDICATED AMPLIFIERS OR SELF-AMPLIFIED SPEAKERS CONFIGURATION 9: 3-ZONE - ONE-WAY PAGING - LOW-POWER SYSTEM - DEDICATED AMPLIFIERS OR SELF-AMPLIFIED SPEAKERS Low-Power System is a switch-selectable feature that allows the system designer to use dedicated amplifiers or self-amplified speakers on the zone outputs.
CONFIGURATION 8: SETUP FOR CONFIGURATION 10: 6 ZONES - ONE-WAY PAGING - MIXED HIGH- AND LOW-POWER ZONES 25/70V AC OR SELF-AMPLIFIED SPEAKERS TWO-WAY TALK BACK EXTENDED PAGING SYSTEM ZONE A ZONE C ZONE B The required setup includes: PCMTIM - 2 PCMCPU - PCMTBM - 4 PCMZPM - 2 PCMPS2 ZONE A ZONE B ZONE C This configuration is essentially the same as the two-way paging system described previously on page 17.The main difference is the addition of a satellite assembly.
CONFIGURATION 10: 6 ZONES - ONE-WAY PAGING - MIXED HIGH- AND LOW-POWER ZONES 25/70V AC OR SELF-AMPLIFIED SPEAKERS RD COM RD B RD C - RD A ZONE C ZONE B - + - + + IN RT ZONE A LOCAL BGM OUTPUT HI PWR LO PWR GLOBL BGM ZONE C ZONE B ZONE A LPBGM VOLUME High- and Low-Power Mixed System is a non-programmable feature that lets the system designer use a dedicated amplifier or self-amplified speaker per zone and at the same time use a centralized amplifier for zones requiring less than 250 wat
CONFIGURATION 7: SETUP FOR CONFIGURATION 11: MICROPHONE OVERRIDE GND ST RLY TWO COM NO NC RLY ONE COM NO NC BGM SRC IN RT OVER RIDE TEL LINE NIGHT RING BGM SRC VOLUME TONE VOLUME This configuration is essentially the same as the one-way paging system described previously.The main difference between the one-way configuration and this configuration is that the centralized high-power amplifier is connected to the PCMTBM module instead of the PCMCPU module.
CONFIGURATION 11: SETUP FOR CONFIGURATION 7:TWO-WAY TALK BACK PAGING SYSTEM MICROPHONE OVERRIDE In addition to the PCM modules, setup requires a Bogen VAR1 (voice-activated relay), PRS40C (12V DC power supply) and an MBS1000 or DDU250 (desktop microphone). ZONE A ZONE B ZONE C Microphone Override is a feature that lets the system designer take priority over all paging functions and make a system-wide page to all speakers.
SETUP FOR CONFIGURATION 12: DFT120 & TAMB WIRING DIAGRAM - LOOP START TRUNK, GROUND START TRUNK OR STATION LEVEL CONFIGURATION 6: EXTENDED PAGING SYSTEM GND ST RLY TWO COM NO NC COM NO RLY ONE BGM SRC IN RT NC OVER RIDE TEL LINE NIGHT RING BGM SRC VOLUME TONE VOLUME As described previously, the required setup for one-way basic configuration includes: PCMTIM, PCMCPU, PCMZPM, and the power supply PCMPS2.
CONFIGURATION 12: DFT120 & TAMB WIRING DIAGRAM - LOOP START TRUNK, GROUND START TRUNK, OR STATION LEVEL RD COM RD B RD C RD A - ZONE C ZONE B - + ZONE A - + + IN RT LOCAL BGM OUTPUT HI PWR LO PWR GLOBL BGM ZONE C OUT BGM IN ZONE B ZONE A LPBGM VOLUME OFF ON TALKBACK POWER ZONE A ZONE B ZONE C PCM ZPM In this configuration, the telephone output is connected to the Bogen Telephone Access Module model TAMB; the TAMB module is connected to the Bogen Digital Feedback Terminator model
CONFIGURATION 5: STATION LEVEL/CENTREX - 3-ZONE - ONE-WAY PAGING - SINGLE AMPLIFIER - 25/70V AC SPEAKERS GND ST RLY TWO COM NO NC RLY ONE COM NO NC BGM SRC IN RT OVER RIDE TEL LINE NIGHT RING BGM SRC VOLUME TONE VOLUME In this configuration, the PCM unit responds to a 90V AC 20Hz ringing signal in pins 3 & 4 of the TEL LINE jack on the PCMTIM module and answers after the first full ring. As soon as it answers, the default timer is started.
SETUP FOR CONFIGURATION 5: STATION LEVEL/CENTREX - 3-ZONE - ONE-WAY PAGING - SINGLE AMPLIFIER - 25/70V AC SPEAKERS CONFIGURATION 13: EMERGENCY VOICE ANNOUNCEMENT OVERRIDE Voice Announcement Override is a non-programmable feature that lets the caller take priority over all paging functions and make a systemwide emergency voice announcement page to all speakers. In addition to the PCM modules, this option requires a ProHold (digital announcer) and a normally open momentary switch supplied by the user.
CONFIGURATION 4: GROUND START TRUNK - 3-ZONE - ONE-WAY PAGING - SINGLE AMPLIFIER - 25/70V AC SPEAKERS GND ST COM RLY TWO In this configuration, the PCM unit supplies a 48V talk battery and loop current detection from pins 3 & 4 of the TEL LINE jack on the PCMTIM module to the ground start trunk in the telephone system.There are two modes of operation for ground start trunk.
CONFIGURATION 14: SETUP FOR CONFIGURATION 4: GROUND START TRUNK - 3-ZONE - ONE-WAY PAGING - SINGLE AMPLIFIER - 25/70V AC SPEAKERS DTMF MICROPHONE ZONE PAGING This section will describe the configuration for the use of a Shure microphone Model 885TT with DTMF dialing capabilities and the MODULINK fiveconductor coil-cord model ALM-1.
CONFIGURATION 3: LOOP START TRUNK - 3-ZONE - ONE-WAY PAGING - SINGLE AMPLIFIER - 25/70V AC SPEAKERS CONFIGURATION 15: SINGLE AMPLIFIER BACKGROUND MUSIC LINE-LEVEL SIGNAL Single amplifier BGM operation is a programmable feature that lets the PCM2000 use the paging amplifier to provide high-power BGM to the 25/70V AC speakers when the paging system is idle.
CONFIGURATION 16: SETUP FOR CONFIGURATION 3: LOOP START TRUNK - 3-ZONE - ONE-WAY PAGING - SINGLE AMPLIFIER - 25/70V AC SPEAKERS PCM ZPM ZONE A ZONE B ZONE C RELAY DRIVER OUTPUT ZONE A ZONE B ZONE C OFF ON TALKBACK SUPRESSION DIODES LPBGM VOLUME RD COM RD B RD C RD A - + ZONE C ZONE B - - + ZONE A + IN RT LOCAL BGM OUTPUT HI PWR LO PWR GLOBL BGM ZONE C ZONE B ZONE A LPBGM VOLUME OFF ON TALKBACK POWER ZONE A ZONE B ZONE C POWER BGM OUT IN RELAY PCM ZPM BGM OUT IN ZONE A
SECTION II - PROGRAMMING SYSTEM PROGRAMMING CONFIGURATION 2: PAGE PORT VOX CIRCUIT - 3-ZONE - ONE-WAY PAGING - SINGLE AMPLIFIER - 25/70V AC SPEAKERS System programming lets you set certain PCM options and tone features using the DTMF keys of a telephone. It also lets you program paging zone groups and signaling zone groups. This configuration is for Page Ports without Contact Closures.
FEATURE CODES AND DEFAULTS SETUP FOR CONFIGURATION 2: PAGE PORT VOX CIRCUIT - 3-ZONE - ONE-WAY PAGING - SINGLE AMPLIFIER - 25/70V AC SPEAKERS RD COM RD B RD C RD A - + - - + ZONE C ZONE B ZONE A ZONE B ZONE A + IN RT LOCAL BGM OUTPUT HI PWR LO PWR GLOBL BGM ZONE C ZONE B BOGEN 0 PCM CPU + Privacy Beep Inhibit Enable Pre-announce Tone Inhibit Beep Chime Confirmation Tone Inhibit Enable Emergency O/R Tone Inhibit Enable All-Call Inhibit Enable Dialing Time-out Inhibit Enable Trunk D
Clock Set Clock Sync.
SECTION I: APPLICATION CONFIGURATIONS RD B RD C RD A - RD COM ZONE A + ZONE C ZONE B - - + ZONE A + IN RT LOCAL BGM OUTPUT HI PWR LO PWR GLOBL BGM ZONE C ZONE B BOGEN 0 COM NC NO RLY TWO RLY ONE COM NC BGM SRC IN RT OVER RIDE TEL LINE NIGHT RING BGM SRC VOLUME TONE VOLUME S1 S2 S3 S4 S5 S6 S7 POWER TEL INT SEL PCM CPU + - - 1.5A GND ST PCM PS2 + 12VDC NO GND AUX GND EM/SC HPBGM RT IN RT OUT PA LPBGM IN RT IN RT PA + 12 VDC 1.
Contents SYS-ID SWITCH SETTINGS CHART FOR ADDITIONAL SATELLITE SYSTEMS Zone #’s S1 S2 S3 S4 1-9 0 0 0 0 1 10-18 1 0 0 0 2 19-27 0 1 0 0 3 28-36 1 1 0 0 4 37-45 0 0 1 0 5 46-54 1 0 1 0 6 55-63 0 1 1 0 7 64-72 1 1 1 0 8 73-81 0 0 0 1 9 82-90 1 0 0 1 10 91-99 0 1 0 1 Master SECTION I - APPLICATON CONFIGURATIONS...................................................................................................................................
PCM2000 Configuration Guide 50 Spring Street, Ramsey, NJ 07446 U.S.A. Tel. 201-934-8500 / Fax 201-934-9832/ www.bogen.